StarTech.com IP2DVI User manual

Ethernet to DVI Video
Adapter
Ethernet to DVI Video Adapter
over IP
IP2DVI
Instruction Manual

FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide rea-
sonable protection against harmful interference in a residential installation. This equip-
ment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio com-
munications. However, there is no guarantee that interference will not occur in a particu-
lar installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.•
Increase the separation between the equipment and receiver.•
Connect the equipment into an outlet on a circuit different from that to which the receiver•
is connected.
Consult the dealer or an experienced radio/TV technician for help.•
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and
do not represent an endorsement of a product or service by StarTech.com, or an en-
dorsement of the product(s) to which this manual applies by the third-party company in
question. Regardless of any direct acknowledgement elsewhere in the body of this doc-
ument, StarTech.com hereby acknowledges that all trademarks, registered trademarks,
service marks, and other protected names and/or symbols contained in this manual and
related documents are the property of their respective holders.

i
Table of Contents
Introduction..................................................................... 1
Packaging Contents.....................................................................1
System Requirements .................................................................1
Installation....................................................................... 1
Hardware Installation...................................................................1
Driver Installation.........................................................................2
Display mode................................................................... 7
Specifications.................................................................. 8
Technical Support........................................................... 9
Warranty Information ...................................................... 9

1
Introduction
Packaging Contents
1 x IP2DVI video adapter•
1 x Power Adapter•
1 x Driver and Software CD•
1 x Instruction Manual•
System Requirements
DVI enabled monitor/projector•
TCP/IP network access•
Microsoft Windows• ®XP/Vista (32-bit)
Installation
Hardware Installation
LAN Port
LAN Link
Indicator
Power Indicator
DVI Connector
Reset Button
Power
Connector

2
LED Indicator
LED Colour Description
Power Red ON: receiving power from adapter
OFF: no power supplied from adapter
Link Green
ON: network connection detected
OFF: no network connection detected
Flashing: data transfer
Driver Installation
Windows XP
Insert the provided CD into your disc drive. Locate and double-click1.
the Setup.exe file in the Driver folder to launch the setup program.
During the installation, the screen may flicker a couple of times. This2.
is normal. When this section of the installation is complete, click
‘Finish’ to proceed.

3
When the ‘Install DisplayLink Software’ screen appears. Accept the3.
terms in the license agreement to proceed.
If you have a firewall enabled on the computer, make sure to unblock4.
the Cat5ShareStation utility.
Connect the IP2DVI unit to your router/switch and power it on.5.
When the Found New Hardware Wizard screen appears, select6.
‘Install the software automatically (Recommended)’ and click Next.
Click ‘Finish’ to complete the installation.7.
Launch the Cat5ShareStation utility from the icon on the Desktop.8.
A list of all available IP2DVI units detected on the network will9.
appear.

4
Select ‘Generic DoIP’ and click the ‘Connect’ button. When the10.
connection is ready, you will see the Generic DoIP icon become
orange as below.
Then a pop-up message will appear in the notification area11.
indicating the installation is complete.
If your monitor is not yet connected to the IP2DVI, make the12.
connection and power on your monitor.
After the connection, the remote monitor should display an image13.
from the computer.

5
Windows Vista
Insert the provided CD into your disc drive. Locate and double-click1.
the Setup.exe file in the Driver folder to launch the setup program.
During the installation, the screen may flicker a couple of times. This2.
is normal. When this section of the installation is complete, click
‘Finish’ to proceed.
When the ‘Install DisplayLink Software’ screen appears. Accept the3.
terms in the license agreement to proceed.

6
After the installation completes, select Yes to restart your computer.4.
Connect the IP2DVI unit to your router/switch and power it on.5.
Launch the Cat5ShareStation utility from the icon on the Desktop.6.
Click ‘unblock’ when you see the Windows Security Alert or other
firewall warning.
Select ‘Generic DoIP’ and click the ‘Connect’ button. When the7.
connection is ready, you will see the Generic DoIP icon become
orange as below.
A pop-up message will appear in the notification area indicating the8.
installation is complete.
If your monitor is not yet connected to the IP2DVI, make the9.
connection and power on your monitor.
After the connection, the remote monitor should display an image10.
from the computer.

7
Display Mode
To change the display mode, right-click on the tray icon located in the
System Tray, next to the clock.
The IP2DVI connected monitor can be configured to:
Extend your Windows desktop (default)
Extend your Windows desktop to Right / Left / Above / Below the
primary display
Mirror your Windows desktop
On Windows XP
On Windows Vista