StarTech.com FAN939775HP User manual

Universal AMD/Intel CPU Cooler
FAN939775HP Instruction Manual
Actual product may vary from photo
Universal Intel/AMD Heatpipe CPU Cooler

FFCCCCCCoommpplliiaanncceeSSttaatteemmeenntt
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
UUsseeooffTTrraaddeemmaarrkkss,,RReeggiisstteerreeddTTrraaddeemmaarrkkss,,aanndd
ootthheerrPPrrootteecctteeddNNaammeessaannddSSyymmbboollss
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and
do not represent an endorsement of a product or service by StarTech.com, or an
endorsement of the product(s) to which this manual applies by the third-party company in
question. Regardless of any direct acknowledgement elsewhere in the body of this
document, StarTech.com hereby acknowledges that all trademarks, registered
trademarks, service marks, and other protected names and/or symbols contained in this
manual and related documents are the property of their respective holders.

TTaabblleeooffCCoonntteennttss
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Warranty Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Instruction Manual
i

IInnttrroodduuccttiioonn
Thank you for purchasing a Universal Intel P4/AMD Athlon Heatsink with fan.Designed to
fit a wide range of Intel and AMD processors, this extra-large heat sink and fan provides
maximum heat dissipation for your hard-working CPU. The fan is capable of moving up to
65 CFM and includes an External Speed Controller that allows you to customize the fan
speed, and in turn the air flow and noise level of the fan.
FFeeaattuurreess
• Universal design: Compatible with Intel P4 , LGA775 and AMD K7 , K8
• Nickel plated Heat Pipe and special welding techniques enable seamless connection
between fins and pipes, for maximum heat dissipation
• Three sets of heat pipes provide high thermal-conductive efficiency
• Easy installation
• Adjustable fan speeds enable control of noise and fan performance
BBeeffoorreeYYoouuBBeeggiinn
System Requirements
• Intel P4, LGA775 (Socket T) or AMD K7, K8, Opteron processor
• 1 available TX3 power connector
• ATX Form Factor case
Contents
This package should contain:
• Heat Pipe Main Unit (1)
• Frame with Fan (1)
• External Speed Controller (1)
• Screw kit (1)
• CPU Fixing bracket kit (1)
• Heatsink Paste (1)
• Instruction Manual (1)
Instruction Manual
1

PPaarrttssLLiisstt
Instruction Manual
2
Heat Pipe Main Unit Frame with Fan External Speed Controller
Screw kit Base/Retention Clip for
Intel P4 Socket 478
Base/Retention Clip for
Intel LGA775 (Socket T)
Retention Clip for AMD
Opteron & K8
Retention Clip for AMD
K7 & Intel P3
CAUTION: Computers contain sensitive electronic components that are easily damaged
by static electricity and excessive shock. When handling the mainboard and other
components, ensure you are properly grounded using an anti-static mat or similar
device. If anti-static equipment is not available, ground yourself by touching the exterior
of the computer case or another large metal surface before handling any peripherals.
Installing FAN939775HP requires that you open your computer case to disconnect and
reconnect wires. If you are unfamiliar with this kind of work, consider bringing your
computer to your local computer store for help.

IInnssttaallllaattiioonn
Note: Although FAN939775HP supports a variety of different CPUs, the illustrations below depict installation on an
Intel chipset. Installation steps are identical for both AMD and Intel chipsets, with the exception of the parts used.
When installing FAN939775 on a Socket AM2 system, please ensure that the motherboard already has the AM2
retention module (mounting bracket), and use the K8 clip.
Instruction Manual
3
1. Remove the original CPU
cooler and any devices used to
retain the CPU within the
socket.
4. Remove the protective film
from the base on the heat pipe
main unit. Place the main unit
on the CPU, aligning the holes
of the P4 clip with the posts.
7. Put the transparent frame onto
the main unit, directing the fan
as required by the structure of
your computer contents.
5. Place the retention clip inside
the frame of the heatpipe
base, then install the main unit
onto the CPU, being sure to
line the clip up with the posts.
3. Apply enough thermal paste to
the top of the CPU to cover the
entire top surface.
2. Place the base clip
backing onto the backside of
the motherboard
6. Tighten the posts to secure the
heatpipe unit onto the
mainboard.
8. Using the screw kit, screw the
frame into the main unit.
9. Connect the power cord from
the fan speed controller to the
main unit/frame.
11. Secure the fan speed
controller into an open slot on
the back of the computer.
10. Connect the remaining power
cable to the motherboard.
12. Check to make sure the main
unit is securely positioned on
the mainboard.

SSppeecciiffiiccaattiioonnss
TTeecchhnniiccaallSSuuppppoorrtt
StarTech.com’s lifetime technical support is an integral part of our commitment to provide
industry-leading solutions. If you ever need help with your product, visit
www.startech.com/support and access our comprehensive selection of online tools,
documentation, and downloads.
WWaarrrraannttyyIInnffoorrmmaattiioonn
This product is backed by a one-year warranty. In addition, StarTech.com warrants its
products against defects in materials and workmanship for the periods noted, following
the initial date of purchase. During this period, the products may be returned for repair, or
replacement with equivalent products at our discretion. The warranty covers parts and
labor costs only. StarTech.com does not warrant its products from defects or damages
arising from misuse, abuse, alteration, or normal wear and tear.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their
officers, directors, employees or agents) for any damages (whether direct or indirect,
special, punitive, incidental, consequential, or otherwise), loss of profits, loss of business,
or any pecuniary loss, arising out of or related to the use of the product exceed the
actual price paid for the product.
Some states do not allow the exclusion or limitation of incidental or consequential
damages. If such laws apply, the limitations or exclusions contained in this statement
may not apply to you.
Instruction Manual
4
Heatsink Dimension 93 x 93 x 98.5 mm
DC Fan Size 92 x 92 x 25 mm
Base Material Heat Pipe
Bearing Type One Ball
Speed 1500 ~ 2800 RPM
Noise Level 18 ~ 28 dBA
Max Air flow 30 ~ 60 CFM
Rated Voltage 12 V.DC
Weight 950 g
Regulatory Certifications FCC, CE

Revised: 15 March 2007 (Revision A)
AAbboouuttSSttaarrTTeecchh..ccoomm
StarTech.com is “The Professionals’ Source for Hard-to-Find Computer
Parts”. Since 1985, we have been providing IT professionals with the
quality products they need to complete their solutions. We offer an
unmatched selection of computer parts, cables, server management
solutions and A/V products and serve a worldwide market through our
locations in the United States, Canada, the United Kingdom and Taiwan.
Visit www.startech.com for complete information about all our products
and to access exclusive interactive tools such as the Parts Finder and the
KVM Reference Guide. StarTech.com makes it easy to complete almost
any IT solution. Find out for yourself why our products lead the industry in
performance, support, and value.