StarTech.com PEXSAT34RH User manual

Manual Revision: 01/08/2013
For the most up-to-date information, please visit: www.startech.com
DE: Bedienungsanleitung - de.startech.com
FR: Guide de l'utilisateur - fr.startech.com
ES: Guía del usuario - es.startech.com
IT: Guida per l'uso - it.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
PT: Guia do usuário - pt.startech.com
PEXSAT34RH
4 Port PCIe SATA III 6Gbps RAID
Controller Card with Heatsink
*actual product may vary from photos

Instruction Manual
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment o and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and do not
represent an endorsement of a product or service by StarTech.com, or an endorsement of the
product(s) to which this manual applies by the third-party company in question. Regardless
of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby
acknowledges that all trademarks, registered trademarks, service marks, and other protected
names and/or symbols contained in this manual and related documents are the property of
their respective holders.

Instruction Manual
i
Table of Contents
Introduction ............................................................................................1
Packaging Contents ................................................................................................................................. 1
System Requirements .............................................................................................................................. 1
Product Diagram ....................................................................................2
Installation ..............................................................................................3
Hardware Installation .............................................................................................................................. 3
Driver Installation ...................................................................................................................................... 4
Verifying Installation ................................................................................................................................ 5
How to Use ..............................................................................................5
RAID Conguration .................................................................................................................................. 5
Specications ..........................................................................................6
Technical Support ..................................................................................7
Warranty Information ............................................................................7

Instruction Manual
1
Introduction
The PEXSAT34RH 4 Port PCI Express SATA III Controller Card adds 4 AHCI SATA III ports
to a computer through a PCIe slot (x2), providing an internal 6Gbps connectivity
solution from a single card.
Compliant with SATA revision 3.0, our PCI Express SATA controller provides up to 6Gbps
of data bandwidth to utilize the speeds of high performance hard drives and solid
state drives (SSD), along with Port Multiplier (PM) support on each port which allows
for multiple SATA drives to be connected over a single cable.
Also, this PCI Express SATA RAID card includes an onboard heatsink to help keep the
card running cool, supports RAID 0, 1, and 1+0, and can handle up to 7 SATA drives
total when using Port Multiplier.
This PCIe SATA 6g card is backed by a 2-year StarTech.com warranty and free lifetime
technical support.
Packaging Contents
• 1x PCIe SATA Controller Card
• 1x Low Prole Bracket
• 1x Driver CD
• 1x Instruction Manual
System Requirements
• PCI Express enabled computer with an available PCI Express x2 slot
• Windows® XP (32/64-bit)/ Server 2003(32/64-bit)/ Vista (32/64-bit)/ 7 (32/64-bit)/
Server 2008 R2/ 8 (32/64-bit), or Apple® Mac OS® 10.6/ 10.7/ 10.8, or Linux®

Instruction Manual
2
4x SATA III ports
Product Diagram

Instruction Manual
3
Installation
Hardware Installation
WARNING! PCI Express cards, like all computer equipment, can be severely damaged
by static electricity. Be sure that you are properly grounded before opening your
computer case or touching your PCI Express card. StarTech.com recommends that you
wear an anti-static strap when installing any computer component. If an anti-static
strap is unavailable, discharge yourself of any static electricity build-up by touching a
large grounded metal surface (such as the computer case) for several seconds. Also be
careful to handle the PCI Express card by its edges and not the gold connectors.
1. Turn your computer o and any peripherals connected to the computer (i.e. Printers,
external hard drives, etc.). Unplug the power cable from the rear of the power
supply on the back of the computer and disconnect all peripheral devices.
2. Remove the cover from the computer case. See documentation for your computer
system for details.
3. Locate an open PCI Express x2 slot and remove the metal cover plate on the rear of
the computer case (Refer to documentation for your computer system for details).
NOTE: This card will work in PCI Express slots of additional lanes (i.e.x4, x8, or x16 slots).
4. Gently insert the card into the open PCI Express slot and fasten the bracket to the
rear of the case.
NOTE: If installing the card into a small form factor/low prole system, replacing the
pre-installed full prole bracket with the included low prole installation bracket may
be necessary.
5. Connect SATA cables from the ports on the card to the SATA devices inside the
computer.
6. Place the cover back onto the computer case.
7. Insert the power cable into the socket on the power supply and reconnect all other
connectors removed in Step 1.

Instruction Manual
4
Driver Installation
Windows XP
NOTE: The latest driver is available from www.startech.com.
1. Once the computer has started and the operating system is fully loaded, insert the
provided Driver CD into the computer’s CD/DVD drive.
2. AutoPlay should give you the option to browse the les on the CD or automatically
open the CD.
If AutoPlay does not start, go into “My Computer” and access the CD/DVD drive that
the CD is in.
3. Open the folder “SATA6G_M9128”. Run the le ‘drvSetup.exe’. Follow the onscreen
instructions to complete the driver installation.
Windows Vista/ 7/ 8
The driver is natively supported by newer Operating Systems. The driver should
automatically install through Windows Update.

Instruction Manual
5
Verifying Installation
Windows
From the main desktop, right-click on “My Computer” (“Computer” in Vista/7/8), then
select Manage. In the new Computer Management window, select Device Manager
from the left window panel.
Under the “SCSI and RAID Controllers” category (“Storage Controllers” in Vista or later),
should be a “Marvell 92xx” device. Right-click on the device and select “Properties” to
make sure it is installed and working correctly.
For Windows 7 and 8, if using the native drivers, the card will instead be listed under
the “IDE ATA/ATAPI Controller” category as a “Standard AHCI” device.
How to Use
RAID Conguration
To setup a RAID array using the drives connected to the SATA controller card, the
BIOS level conguration menu must be accessed. To access the conguration menu,
during POST (computer startup), the status display for the controller card will display.
When prompted, pressing [CTRL] + [m] will enter the conguration menu. From the
conguration menu, the detected drives can be congured into any of the supported
RAID modes by following the on screen prompts.

Instruction Manual
6
Specications
Host Interface PCI Express 2.0
SATA Revision 3.0
Form Factor Full/Low Prole
Chipset ID Marvell 9230
Internal Connectors 4x 7-pin SATA plug
Maximum Transfer Rate SATA: 6Gbps
RAID Support RAID 0, 1, 1+0
Port Multiplier Yes*
Operating Temperature 5°C ~ 50°C (41°F ~ 122°F)
Storage Temperature -25°C ~ 70°C (-13°F ~ 158°F)
Humidity 20% ~ 80% RH
Dimensions (LxWxH) 80mm x 120mm x 20mm
Weight 50g
Compatible Operating Systems
Windows XP(32/64-bit)/ Server
2003(32/64-bit)/ Vista(32/64-bit)/
7(32/64-bit)/ Server 2008 R2/ 8(32/64-
bit), Mac OS 10.6/ 10.7/ 10.8, Linux
*Port Multiplier is not supported in Mac OS

Instruction Manual
7
Technical Support
StarTech.com’s lifetime technical support is an integral part of our commitment to
provide industry-leading solutions. If you ever need help with your product, visit
www.startech.com/support and access our comprehensive selection of online tools,
documentation, and downloads.
For the latest drivers/software, please visit www.startech.com/downloads
Warranty Information
This product is backed by a two year warranty.
In addition, StarTech.com warrants its products against defects in materials
and workmanship for the periods noted, following the initial date of purchase.
During this period, the products may be returned for repair, or replacement with
equivalent products at our discretion. The warranty covers parts and labor costs only.
StarTech.com does not warrant its products from defects or damages arising from
misuse, abuse, alteration, or normal wear and tear.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their
ocers, directors, employees or agents) for any damages (whether direct or indirect,
special, punitive, incidental, consequential, or otherwise), loss of prots, loss of business,
or any pecuniary loss, arising out of or related to the use of the product exceed the
actual price paid for the product. Some states do not allow the exclusion or limitation
of incidental or consequential damages. If such laws apply, the limitations or exclusions
contained in this statement may not apply to you.

Hard-to-nd made easy. At StarTech.com, that isn’t a slogan. It’s a promise.
StarTech.com is your one-stop source for every connectivity part you need. From
the latest technology to legacy products — and all the parts that bridge the old and
new — we can help you nd the parts that connect your solutions.
We make it easy to locate the parts, and we quickly deliver them wherever they need
to go. Just talk to one of our tech advisors or visit our website. You’ll be connected to
the products you need in no time.
Visit www.startech.com for complete information on all StarTech.com products and
to access exclusive resources and time-saving tools.
StarTech.com is an ISO 9001 Registered manufacturer of connectivity and technology
parts. StarTech.com was founded in 1985 and has operations in the United States,
Canada, the United Kingdom and Taiwan servicing a worldwide market.