StarTech.com SATDUP13 User manual

Manual Revision: 09/20/2013
For the most up-to-date information, please visit: www.startech.com
DE: Bedienungsanleitung - de.startech.com
FR: Guide de l'utilisateur - fr.startech.com
ES: Guía del usuario - es.startech.com
IT: Guida per l'uso - it.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
PT: Guia do usuário - pt.startech.com
SATDUP13
1 to 3 Standalone Hard Drive Duplicator
and Eraser
*actual product may vary from photos

Instruction Manual
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment o and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and do not
represent an endorsement of a product or service by StarTech.com, or an endorsement of the
product(s) to which this manual applies by the third-party company in question. Regardless
of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby
acknowledges that all trademarks, registered trademarks, service marks, and other protected
names and/or symbols contained in this manual and related documents are the property of
their respective holders.

Instruction Manual
i
Table of Contents
Product Diagram ....................................................................................1
Front View .................................................................................................................................................... 1
Rear View...................................................................................................................................................... 1
Introduction............................................................................................2
Packaging Contents ................................................................................................................................. 2
Hardware Installation............................................................................3
Hardware Operation..............................................................................4
Hard Drive Duplication ........................................................................................................................... 4
Compare Duplicated Drives .................................................................................................................. 5
Compare & Duplicated Drives .............................................................................................................. 5
Hard Drive Eraser....................................................................................................................................... 5
Utility Options ............................................................................................................................................ 7
Advanced Conguration Using Setup ................................................8
Technical Support ..................................................................................10
Warranty Information............................................................................10

Instruction Manual
1
Product Diagram
Front View
1. Display Screen
2. Navigation buttons
3. OK button
4. Esc button
5. SATA HDD source port
6. SATA HDD destination ports
Rear View
1. Power Switch
2. Power Adapter Port
3. Daisy Chain ports
1
1

Instruction Manual
2
Introduction
Packaging Contents
• 1 x 1 to 3 HDD Duplicator/Eraser
• 4 x SATA Cables
• 1 x Power Adapter
• 3 x Power Cords (NA, UK, EU)
• 1 x Instruction Manual
WARNING! Hard drives and storage enclosures require careful handling, especially
when being transported. If you are not careful with your hard disk, lost data may
result. Always handle your hard drive and storage device with caution. Be sure that
you are properly grounded by wearing an anti-static strap when handling computer
components or discharge yourself of any static electricity build-up by touching a large
grounded metal surface (such as the computer case) for several seconds.

Instruction Manual
3
3. Using an included SATA Cable, connect up to 3 HDDs you would like to have over
written, or erased to the destination ports. (3 ports from right to left , see below
WARNING! Any Data remaining on the destination drives will be over written.
Note: If using less than 3 HDDs, drives should be connected from left to right
leaving port(s) closest to the right unoccupied.
4. Press the power switch to the “On” position, the SATDUP13 is now ready to use.
Hardware Installation
1. Ensure the power switch is set in the o position. Connect the included power
adapter from an available AC power outlet to the Power Adapter Port on the back
of the SATDUP13.
2. Using an included SATA Cable, attach the HDD you would like to duplicate to the
source port (rst port on the left, see below)

Instruction Manual
4
Hardware Operation
Hard Drive Duplication
1. Using the Navigation buttons, locate“HDD Duplicator 1. Copy” and press OK. Default
copy mode is“System and Files”. To change Copy mode please see “Setup section”.
2. The duplicator will analyze the source drive and ensure all the targets are ready,
by verifying size. Once the drives have been analyzed you will receive an indicator
stating the duplicator is ready. Press OK, and the system will begin duplication
automatically.
3. Duplication will complete when the % indicator reaches 100%. The destination
drives now contain identical data to the source drive.
Note: If the destination drives are larger than the source drive, a single partition the
size of the source drive will be on the destination drive.

Instruction Manual
5
Compare Duplicated Drives
The Compare function ensures the Hard Drive duplication was accurate.
1. After your Hard Drive duplication has completed, locate “HDD Duplicator 2.
Compare”Using the Navigation buttons, and press OK.
2. Once compare has completed. A report will be displayed with the results of the
compare test.
Compare & Duplicated Drives
The Copy+Compare function will both copy the Hard Drive and ensure the duplication
was accurate.
1. After your Hard Drive duplication has completed, locate “HDD Duplicator 2.
Compare”Using the Navigation buttons, and press OK.
2. The duplicator will analyze the source drive and ensure all the targets are ready,
by verifying size. Once the drives have been analyzed you will receive an indicator
stating the duplicator is ready. Press OK, and the system will begin duplication
automatically.
3. Duplication will complete when the % indicator reaches 100%. The destination
drives now contain identical data to the source drive, and the Compare operation
will begin.
4. Once compare has completed. A report will be displayed with the results of the
compare test.
Hard Drive Eraser
1. Using the Navigation buttons, locate“HDD Duplicator 4. Erase”and press OK
2. The erase function is used to delete the data in your HDD. Please choose your
desired erase method from the list below using the navigation buttons then press
okay.

Instruction Manual
6
Note: The number 4 at the beginning of each option below represents the Erase
heading on the main menu, the numbers: .1, .2, .3, etc. indicate the option within
the Erase sub menu.
4.1 Quick Erase
The function will ONLY erase the index of the HDD, which is the quickest way to erase
it. Quick Erase will damage the data on the HDD, so please make sure you have backed
up all important data before using this function.
4.2 Full Erase
The function will erase the whole drive by overwriting each sector on the target HDD
and will take longer than quick erase. Full Erase will damage the data on the HDD, so
please make sure you have backed up all important data before using this function.
4.3 DoD Erase
DoD Erase is an erasing method that complies with the U.S.A. Department of Defense
(DoD) standard. It can guarantee the data was fully deleted by erasing the HDD bit for
bit three times. DoD Erase will damage the data on the HDD, so please make sure you
have backed up all important data before using this function.
4.4 DoD Erase & Compare
DoD Erase & Compare performs a standard DoD Erase as described above, then
performs a sector by sector check to verify that the drive has been erased. As it does
the most thorough Erasing job, it is also takes the most time to complete.
3. Press OK to begin the erasing process.
4. Once the erase has completed the result will be displayed.

Instruction Manual
7
Utility Options
1. Using the Navigation buttons, locate“HDD Duplicator 5. Utility” and press OK.
2. From the Utility options you can access dierent administrative congurations and
information. See the list below outlining the details of each option.
Note: The number 5 at the beginning of each option below represents the Utility
heading on the main menu, the numbers: .1, .2, .3, etc. indicate the option within
the Utility sub menu.
5.1 Show Disk Info
The function shows basic information from the drive connected to the source.
5.2 Update System
If an update to the device rmware is available on the StarTech.com product page,
this option can be used to update the device. The steps below outline the steps for
executing a system update.
Note: A rmware update should only be done if recommend by StarTech.com.
The below steps should only be performed by advanced users. Please contact
StarTech.com Technical Support for assistance.
a) Format a blank hard drive with a 10GB FAT32 partition.
b) Download the rmware le from the StarTech.com Website, and place the le on the
main directory of the new partition.
c) Connect the hard drive to the source port of the SATDUP13.
d) Using the Navigation Buttons locate “5.2.1 Update BIOS”and press ok.
e) The update will take place, and the on screen display will alert you upon
completion.