StarTech.com DK30CHPH User manual

Quick-Start Guide
To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.
ManualRevision:December23,2020
Product Diagram (DK30CHPH)
Front View
Rear View
Side View
USB-C™ HDMI Tablet and Smartphone Docking Station - iPad Pro & Android - HDMI
Port Function
1USB-C Host Port
• SuperSpeed USB 5Gbps (USB 3.2 Gen 1)
• DP 1.2 Alt Mode
• Charge the Host Device while using the Docking
Station
• PD3.0 5/9/12/15V
• Connect to a Phone or a Tablet
2USB 2.0 Ports
• USB 2.0
• Connect a USB-A Storage Device (e.g. ash drive),
or a USB-A Peripheral Device
3SuperSpeed USB Port
• SuperSpeed USB 5Gbps (USB 3.2 Gen 1)
• Connect a USB-A Storage Device (e.g. ash drive),
or a USB-A Peripheral Device
4DC Power Input Port
• Type-N barrel connector
• 45W (20V 2.25A)
• Connect the Universal Power Adapter to supply
power to the Docking Station
5HDMI Output Port
• HDMI 2.0b
• 4K @ 30Hz
• Connect an HDMI Display Device
6RJ45 Port
• 10/100/1000 Mbps
• Connect a Network Cable to establish a network
connection
7LED Indicator • Green indicates the Host Device and Power
Source are connected
Requirements
For the latest requirements and to view the full manual, please visit:
www.startech.com/DK30CHPH.
• Host Computer with USB-C Port
• DP-Alt Mode Compatible
• USB PD Support
1
2
4 5 6
3
7

FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation. Changes or modications not expressly approved by StarTech.com could void
the user’s authority to operate the equipment.
Industry Canada Statement
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.
CAN ICES-3 (B)/NMB-3(B)
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) This device may not cause interference, and (2) This device must accept any interference, including interference that may
cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en compromettre le fonctionnement.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-
party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only
and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which
this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered
trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the
property of their respective holders.
iPad Pro® is a trademark of Apple Inc., registered in the U.S. and other countries.
Warranty Information
This product is backed by a three-year warranty.
For further information on product warranty terms and conditions, please refer to www.startech.com/warranty.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors, employees or agents)
for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of prots, loss of
business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product.
Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations
or exclusions contained in this statement may not apply to you.
Safety Measures
• If product has an exposed circuit board, do not touch the product under power.
Mesures de sécurité
• Si l’un des circuits imprimés du produit est visible, ne pas touchez le produit lorsqu’il est sous tension.
安全対策
• 製品に露出した状態の回路基盤が含まれる場合、電源が入っている状態で製品に触らないでください。
Misure di sicurezza
• Se il prodotto ha un circuito stampato visibile, non toccare il prodotto quando è acceso.
Säkerhetsåtgärder
• Rör aldrig vid enheter med oskyddade kretskort när strömmen är påslagen.
FR: fr.startech.com
DE: de.startech.com
ES: es.startech.com
NL: nl.startech.com
IT: it.startech.com
JP: jp.startech.com
StarTech.com Ltd.
45 Artisans Cres
London, Ontario
N5V 5E9
Canada
StarTech.com Ltd.
Unit B, Pinnacle 15
Gowerton Rd,
Brackmills
Northampton
NN4 7BW
United Kingdom
StarTech.com LLP
4490 South Hamilton
Road
Groveport, Ohio
43125
U.S.A.
- and/or -
• Connect a SuperSpeed USB 5Gbps (USB 3.2 Gen 1) Peripheral to the SuperSpeed
USB Port on the rear of the Docking Station.
Connect a Display
• Connect an HDMI M/M Cable to the HDMI Output Port on the Docking Station
and to the HDMI Input Port on the rear of the HDMI Display Device.
Connect to a Network
• Connect a Network Cable to the RJ45 Port on the rear of the Docking Station and
to the Network Device.
Connect a Power Source
• Connect the Universal Power Adapter to the DC Power Input Port on the rear of
the Docking Station and to an AC Electrical Outlet.
Operation
RJ45 Port LED Indicators
LED Color Status Indication
Green Solid • Link speed is either 1000 Mbps (1 GbE), 100 Mbps,
or 10 Mbps
O • No connection established
Amber Flashing • Network trac detected
On • Link detected
Installation
Notes: Installation is automatic for all modern Operating Systems.
Shutting down the iPad Pro® (not sleep mode or restart) and leaving it
connected to the Docking Station before powering it back on, may result
in no HDMI video output. If this happens, disconnect and reconnect the 1M
USB-C Cable (included) from the USB-C Host Port on the front of the Docking
Station.
Windows 7 (and earlier) Driver Installation
1. If the Found New Hardware dialog box appears on the screen, close the dialog box
or click Cancel.
Note: Once the Docking Station is connected to the Host Device, and if no existing
Drivers are found, the Docking Station will load a CD-ROM Device that contains an
executable le that can be used to install the Driver.
2. After the CD-ROM Device nishes loading, run the Installation File.
3. Complete the on-screen instructions to nish the installation.
Note: Download the latest software from the StarTech.com website,
www.StarTech.com/DK30CHPH.
Connect a Host Device
• Connect the 1M USB-C Cable (included) to the USB-C Host Port on the front of the
Docking Station and to the USB-C Port on a Laptop, Computer, Phone, or a Tablet.
Connect USB Peripherals
• Connect up to two USB 2.0 Peripherals to the USB 2.0 Ports on the rear of the
Docking Station.