StarTech.com InfoSafe IDECASE35U2 User manual

InfoSafe Mobile Drive Enclosure
IDECASE35U2 Instruction Manual
Actual product may vary from photo
External USB 2.0 3.5” Hard Drive Enclosure with Active Cooling

UUsseeooffTTrraaddeemmaarrkkss,,RReeggiisstteerreeddTTrraaddeemmaarrkkss,,aanndd
ootthheerrPPrrootteecctteeddNNaammeessaannddSSyymmbboollss
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and
do not represent an endorsement of a product or service by StarTech.com, or an
endorsement of the product(s) to which this manual applies by the third-party company in
question. Regardless of any direct acknowledgement elsewhere in the body of this
document, StarTech.com hereby acknowledges that all trademarks, registered
trademarks, service marks, and other protected names and/or symbols contained in this
manual and related documents are the property of their respective holders.

TTaabblleeooffCCoonntteennttss
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Installing a Hard Drive in the Enclosure . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Installing Drivers (Windows 98/98SE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Connecting the Enclosure to a Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Disconnecting the Enclosure from a Computer . . . . . . . . . . . . . . . . . . . . . . .4
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Accessory Products from StarTech.com . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Warranty Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Instruction Manual
i

IInnttrroodduuccttiioonn
Thank you for purchasing a StarTech.com USB 2.0 mobile InfoSafe drive enclosure for
3.5” EIDE hard drives. You you can use this drive enclosure to turn a standard hard drive
into a portable storage solution for backup, multimedia, and other demanding
applications. With an integrated fan, your hard drive will be kept cool while transferring
data at up to 480 Mbits/sec.
FFeeaattuurreess
• Supports virtually any 3.5” EIDE hard drive
• Rugged design for excellent durability
• Active cooling with an integrated 8 cm (3.15”) fan for increased drive reliability
• Transfers data at up to 480 Mbits/sec.
BBeeffoorreeYYoouuBBeeggiinn
System Requirements
• A computer with an available USB port, running one of the following operating
systems: Windows 98/98SE/ME/2000/XP/2003 Server, Mac OS X
NOTE: This product will function on a USB 1.1-compliant port at reduced speeds. If you
are using this product with a USB hub, the hub must also be USB 2.0 compliant for best
speed results. This product should also function on other operating systems (i.e. Linux)
that support USB and removable drives, however only Windows and Mac OS installations
are directly supported by StarTech.com technical support.
Contents
This package should contain:
• 1 x IDECASE35U2
• 1 x USB 2.0 Data Cable
• 1 x Set of Drive Mounting Screws
• 1 x Power Adapter
• 1 x Driver Diskette
• 1 x User Manual
Instruction Manual
1

IInnssttaallllaattiioonn
Installing a Hard Drive in the Enclosure
Use caution when installing a hard drive in the enclosure. Excessive shock or force
could damage the drive and/or the enclosure, resulting in data loss.
CAUTION: Always ensure that you are properly grounded when handling a hard drive or
the enclosure tray, since electronic components can be damaged by static electricity. If
an anti-static mat or similar product is not available, ground yourself by touching a
computer case or other metal surface for several seconds before handling any
components.
1. Loosen the two screws on the back of the enclosure holding the drive tray in place.
Note that they cannot be removed, but will stay in the tray.
2. Using the tab at the top of the tray,
gently remove the tray from the enclosure.
3. (a) Place the hard drive on top of the tray, lining up the connectors on the hard
drive with the connectors on the back of the tray.
(b) If necessary, you can adjust the position of the power
connector in the tray for a better fit with the hard drive you
are installing. Loosen the screw marked Adjustable
screw and
gently move the power connector to the left or
right as necessary. When you are satisfied with the new
position of the power connector in the tray, re-tighten the screw so the connector no
longer moves. Do not install the hard drive until you have re-secured the power
connector in the tray.
4.
Gently slide the hard drive into place until the connectors on the tray are seated
snugly into the drive.
5. Carefully turn the tray upside down. The screw holes on the hard drive should line up
with those on the tray. Use the provided screws to secure the drive in the tray; turn
the screws until they are snug and the drive does not move. Do not over-tighten.
Instruction Manual
2
Power Switch
USB
Power Adapter Tray Screws
Power/Activity LED
Green = Power
Red (flashing) = Drive Activity
(Rear View)
(Front View)
(With Tray Removed)

6. Insert the tray into the enclosure until the rear panel is flush to the sides of the case.
Re-tighten the screws you loosened in step 1. Ensure there is no movement of the
tray in the enclosure and continue to tighten the screws as needed. Once the screws
are tightened snugly and the tray does not move, the drive is ready to be used.
Installing Drivers (Windows 98/98SE)
Windows ME/2000/XP/2003 Server and Mac OS X all support removable hard drives
without additional software. Ensure you have the most current updates installed.
Computers running Windows 98/98SE need to install support for USB removable mass
storage devices before using the enclosure:
1. Go to Start, Settings, Control Panel. Double click Add New Hardware.
2. When the Add New Hardware Wizard opens, click Next. Click Next again to allow
Windows to search for Plug and Play devices.
3. When the Wizard is finished, choose No, the device isn’t in the list and click Next.
On the next menu, choose No, I want to select the hardware from a list and click
Next.
4. From the list, choose Other as the type of device you are installing and click Next.
5. Click Have Disk. Insert the driver disk in your floppy drive. Type A: as the path
name, and click OK. Click OK again to confirm the name of the .ini file.
6. Windows will show you which driver it is installing. Click OK.
7. Click Finish to complete the installation.
Connecting the Enclosure to a Computer
This product has been tested with Windows 98/98SE, ME, 2000, XP, 2003 Server, and
Mac OS X. Other operating systems may also support this device; consult your
documentation or a computer service professional for details on whether this product will
work with your operating system and configuration.
When used with the Windows operating systems noted above, the drive enclosure is
“hot-swappable” which means the drive can be connected and disconnected while the
computer is running and will be immediately accessible to the user like any other hard
drive.
1. Place the enclosure near the computer you wish to use.
2. Using the provided USB 2.0 data cable, connect one end to the USB connector
on the rear panel of the enclosure. Connect the opposite end of the cable to an
available USB connector on the back of the computer or a USB hub.
3. Plug the power adapter into a wall outlet or other suitable power source. Connect the
opposite end to the connector on the rear panel of the enclosure.
4. Switch the power button marked I O on the rear panel of the enclosure to the On (I)
position. The LED indicator on the front of the enclosure will light green. The drive
should be ready to use and will be visible under My Computer (Windows) or on the
desktop (Mac OS).
Instruction Manual
3

Disconnecting the Enclosure from a Computer
1. Ensure that any programs that have accessed the drive are closed.
2. Ensure that the LED on the front of the enclosure is not flashing red, which indicates
the drive is being accessed.
3. Switch the power button marked I O on the rear panel of the enclosure to the Off (O)
position. The LED will no longer be lit.
4. You can now safely remove the USB 2.0 data cable from the enclosure.
Specifications
Instruction Manual
4
Drive Compatibility ATA/33/66/100/133 EIDE
3.5” drive form factor supported
Data Transfer Rate 480 Mbits/sec. (maximum) when connected to a USB 2.0 controller
(Actual transfer rates may vary depending on drive model and configuration)
Drive Cooling Mechanism 8 cm. fan with side and rear venting
Power Adapter Input: 100-240V AC (auto-switching) 50/60Hz, 0.55A
Adapter Output: 12V DC, 2A, Center Positive
Certifications CE (Enclosure)
FCC Class B, CE, UL, CB (Power Adapter)

AAcccceessssoorryyPPrroodduuccttssffrroommSSttaarrTTeecchh..ccoomm
Contact your local StarTech.com dealer or visit www.startech.com for cables or other
accessories that will help you get the best performance out of your new product.
CBUSB220
2 Port USB 2.0 CardBus Adapter
PCI225USB
Value 2 Port USB 2.0 PCI Card
PCI225USB_LP
Low Profile 2 Port USB 2.0 PCI Card
PCI420USB
4 Port USB 2.0 PCI Card
PCI425USB
Value 4 Port USB 2.0 PCI Card
PCI625USB2I
Value 6 Port USB 2.0 PCI Card
CB2U2F
2 Port USB 2.0 and 2 Port IEEE-1394 FireWire CardBus Slot Saver Adapter
PCI3UV22F
3 Port USB 2.0 and 2 Port IEEE-1394 FireWire Slot Saver PCI Card
PCISATA2U5
2 Port Serial ATA and 5 Port USB 2.0 Slot Saver PCI Card
PCISAT2F3U4
2 Port Serial ATA, 3 Port IEEE-1394 FireWire and 4 Port USB 2.0 Slot Saver PCI Card
USB2HAB6T
6 ft. Transparent USB 2.0 Cable A-B M/M
USB2HAB10T
10 ft. Transparent USB 2.0 Cable A-B M/M
USB2HAB15T
15 ft. Transparent USB 2.0 Cable A-B M/M
USB2HAB6
6 ft High Speed Certified USB 2.0 Cable
USB2HAB10
10 ft High Speed Certified USB 2.0 Cable
Instruction Manual
5

TTeecchhnniiccaallSSuuppppoorrtt
StarTech.com’s lifetime technical support is an integral part of our commitment to provide
industry-leading solutions. If you ever need help with your product, visit
www.startech.com/support and access our comprehensive selection of online tools,
documentation, and downloads.
WWaarrrraannttyyIInnffoorrmmaattiioonn
This product is backed by a one-year warranty. In addition, StarTech.com warrants its
products against defects in materials and workmanship for the periods noted, following
the initial date of purchase. During this period, the products may be returned for repair, or
replacement with equivalent products at our discretion. The warranty covers parts and
labor costs only. StarTech.com does not warrant its products from defects or damages
arising from misuse, abuse, alteration, or normal wear and tear.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their
officers, directors, employees or agents) for any damages (whether direct or indirect,
special, punitive, incidental, consequential, or otherwise), loss of profits, loss of business,
or any pecuniary loss, arising out of or related to the use of the product exceed the
actual price paid for the product.
Some states do not allow the exclusion or limitation of incidental or consequential
damages. If such laws apply, the limitations or exclusions contained in this statement
may not apply to you.
Instruction Manual
6

Revised: 18 April 2005 (Rev. A)