StarTech.com S252SMTB3 User manual

Manual Revision: 12/04/2013
For the most up-to-date information, please visit: www.startech.com
DE: Bedienungsanleitung - de.startech.com
FR: Guide de l'utilisateur - fr.startech.com
ES: Guía del usuario - es.startech.com
IT: Guida per l'uso - it.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
PT: Guia do usuário - pt.startech.com
S252SMTB3
ThunderBolt Dual 2.5” SATA SSD/HDD
Enclosure
*actual product may vary from photos

Instruction Manual
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment o and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and do not
represent an endorsement of a product or service by StarTech.com, or an endorsement of the
product(s) to which this manual applies by the third-party company in question. Regardless
of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby
acknowledges that all trademarks, registered trademarks, service marks, and other protected
names and/or symbols contained in this manual and related documents are the property of
their respective holders.

Instruction Manual
i
Table of Contents
Product Diagram ....................................................................................1
Front View .................................................................................................................................................... 1
Rear View...................................................................................................................................................... 1
Introduction............................................................................................2
Packaging Contents ................................................................................................................................. 2
System Requirements.............................................................................................................................. 2
Installation ..............................................................................................3
Hardware Installation .............................................................................................................................. 3
How to Use ..............................................................................................6
Connecting the Hard Drives.................................................................................................................. 6
LED Indicator .............................................................................................................................................. 6
Disconnecting the Hard Drive.............................................................................................................. 6
Initializing the Hard Drive ...................................................................................................................... 7
Technical Support ..................................................................................8
Warranty Information............................................................................8

Instruction Manual
1
Product Diagram
Front View
1. Status LED
2. Drive Activity LEDs
Rear View
1. Drive bay panel
2. Thumb screws
3. Drive Fan
4. Power Jack
5. 2 x Thunderbolt ports

Instruction Manual
2
Introduction
Packaging Contents
• 1 x Thunderbolt 2.5” HDD RAID Enclosure
• 1 x Thunderbolt Cable
• 1 x HDD installation screw kit
• 1 x Universal Power Adapter w/ regional power cables (NA/EU/UK/AUS)
• 1 x Rubber foot set
• 1 x Instruction Manual
System Requirements
• 1x Computer system with available Thunderbolt port
Microsoft® Windows® 8/7/Server 2008 R2 (32/64-bit)
Apple® Mac® OSX
Linux®
• 2 x 2.5” SATA SSD/HDDs

Instruction Manual
3
2. Remove the drive panel by lifting it up and outward.
Note: Drive fan cables will stay connected to the panel and the rest of the enclosure
Installation
Hardware Installation
WARNING! Hard drives and storage enclosures require careful handling, especially
when being transported. If you are not careful with your hard disk, lost data may
result. Always handle your hard drive and storage device with caution. Be sure that
you are properly grounded by wearing an anti-static strap when handling computer
components or discharge yourself of any static electricity build-up by touching a large
grounded metal surface (such as the computer case) for several seconds.
1. Remove the thumb screws on the back of the enclosure by turning them counter
clockwise until released.

Instruction Manual
4
3. Grasp the drive tray handels to slide each of the drive trays out of the enclosure
4. Place the drive tray arround your 2.5”HDD/SSD with the label facing upward.
5. Fix four of the included hdd installation screws into place through the screw holes
on the drive tray using a Phillips head screw driver (not included). Repeat this
process for your second drive using the other drive tray.

Instruction Manual
5
6. Slide the drive trays back into drive slots on the HDD Enclosure.
7. Replace the drive panel and thumb screws.
8. Connect the included thunderbolt cable from one of the Thunderbolt ports on the
back of the enclosure, to an available Thunderbolt port on your computer.
Note: Either Thunderbolt port may be used to connect the enclosure to the host
computer system. The remaining Thunderbolt port may be used to daisy chain to
an additional device such as another enclosure, or Display.
9. Connect your power adapter from the power jack on the unit into an available
power outlet.

Instruction Manual
6
How to Use
Connecting the Hard Drives
Once the enclosure has been attached to a computer, and your the drivers will install
automatically, and the inserted drives will be accessible as though they were installed
within the system.
Prior to using the drive array, it will need to be formatted according to your operating
system requirements. Refer to Initializing the Hard Drive
LED Indicator
The hard drive enclosure oers LED indicators for each drive, so you can monitor drive
activity. The LED will ash while the hard drive is being accessed. Do not remove the
enclosure from the host computer while the LED is ashing, as it could damage the
drive or the enclosure, resulting in data loss.
Disconnecting the Hard Drive
Windows
1. Select the “Safely remove Hardware and Eject Media” icon, located in the task bar.
2. Select the Mass Storage Device from the list that appears.
3. Wait for the message indicating that it is now safe to remove the device.
Note: Removing the connected drive prior to receiving notication that it is safe to
do so, could result in losing or corrupting data stored on the drive. Once the Safe
to Remove Hardware message appears, please disconnect the enclosure from the
computer by removing the USB connection.
Mac OS X
To safely disconnect the attached drive from the host computer, close any windows
listing the contents of the removable drive. Once all windows are closed, click on the
drive icon on the desktop, and drag it to the Trash Can icon on the desktop. Allow 5
seconds before physically removing the enclosure/drive from the computer.

Instruction Manual
7
Initializing the Hard Drive
1. If the drive array is new it may need to be initialized and formatted before use. From
the main Windows desktop, right-click on “My Computer” (“Computer” in Vista/ 7
/ 8), then select Manage. In the new Computer Management window, select Disk
Management from the left window panel.
2. A dialog window should automatically appear, asking you to initialize the drive.
Depending on the version of Windows, it will give you the option of either creating
an “MBR” or“GPT” disk. GPT (GUID partition) is required for drives larger than 2TB but
is not compatible with some older operating systems, while MBR is supported by
newer and older operating systems.
3. Once initialized, locate the Disk that says it is “Unallocated” (check the listed hard
drive capacity to conrm it’s the correct hard drive) and then right-click in the
section that says “Unallocated” and select “New Partition”.
4. Several on screen prompts will follow walking you through the steps to create the
partition. Follow the prompts to complete partition creation.