StarTech.com RK616WALM User manual

Manual Revision: 05/10/2019
User Manual
For the latest information and specications visit
www.startech.com/RK616WALM
6U Wall-Mount Rack Enclosure
Actual product may vary from photos
SKU#: RK616WALM

1
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Use of Trademarks, Registered Trademarks, and other
Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and
other protected names and/or symbols of third-party companies not related in
any way to StarTech.com. Where they occur these references are for illustrative
purposes only and do not represent an endorsement of a product or service
by StarTech.com, or an endorsement of the product(s) to which this manual
applies by the third-party company in question. Regardless of any direct
acknowledgement elsewhere in the body of this document, StarTech.com
hereby acknowledges that all trademarks, registered trademarks, service marks,
and other protected names and/or symbols contained in this manual and
related documents are the property of their respective holders.

2
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Warning Statements
Read the entire manual and make sure that you understand the instructions
before you start to assemble and use this product.
Wall structures vary, and it is important to make sure that the type of wall
structure and mounting hardware that you are using will properly support the
mounted equipment. Failure to do so might result in personal injury and/or
equipment damage. The wall structure should be capable of supporting at least
four times the weight of the mounted equipment.
This enclosure is extremely heavy. Never attempt to move or lift this enclosure
without assistance.
Tipping hazard! Extending multiple components from this enclosure increases
the chance that the enclosure will tip over. To avoid this risk, do not extend more
than one component from the enclosure.
Do not place any items on this enclosure and do not stack the enclosure on top
of another enclosure.
Keep liquid away from this enclosure.
Make sure that you install the enclosure in an area that can handle the
combined weight of the enclosure and the equipment that you intend to place
inside of the enclosure.
This product requires an earth ground connection. Do not use this product
without an earth ground connection.
Before you add equipment to this product, make sure that you have properly
assembled, installed, and mounted it to a wall.
When you load equipment into this product, load the heaviest equipment
in the bottom section of this product rst. Continue loading equipment in a
descending order of weight, so that the lighter equipment is installed in the
upper sections of this product and the heavier items are on the bottom.
Varningsmeddelanden
Läs hela manualen och se till att du förstår instruktionerna innan du börjar
montera och använda produkten.
Eftersom väggstrukturer varierar är det viktigt att kontrollera att väggstrukturen
och monteringsutrustningen som du använder klarar av den monterade

3
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
utrustningen. Om du inte gör det kan skada på person och/eller utrustning
uppstå. Väggstrukturen ska kunna klara av minst fyra gånger vikten av den
monterade utrustningen.
Detta skåp är extremt tungt. Försök aldrig ytta på skåpet eller lyfta det utan
hjälp.
Risk för vältning! Att förlänga era komponenter från detta skåp ökar risken för
att det välter. Förläng inte er än en komponent från skåpet för att undvika risk.
Placera inte saker ovanpå skåpet och ställ inte skåpet ovanpå ett annat skåp.
Håll vätskor borta från skåpet.
Se till att du installerar skåpet på en plats som kan hantera den kombinerade
vikten av skåpet och utrustningen som du tänker placera inuti.
Produkten behöver en jordad anslutning. Använd inte produkten utan en jordad
anslutning.
Innan du lägger till utrustning till produkten, se till att du har monterat,
installerat och fäst den till en vägg korrekt.
När du lastar produkten med utrustning, ställ in den tyngsta utrustningen i den
nedersta delen först. Fortsätt ställa in utrustning i viktordning, så att den lättare
utrustningen installeras i de övre delarna och den tyngre utrustningen är längst
ner.
Waarschuwingen
Lees de gehele handleiding en zorg dat u de instructies begrijpt voordat u dit
product in elkaar zet en gebruikt.
Omdat wandstructuren verschillen, is het belangrijk dat u ervoor zorgt dat het
type wandstructuur en de montagemiddelen die u gebruikt de gemonteerde
apparatuur goed ondersteunen. Anders zou lichamelijk letsel en/of schade aan
de apparatuur kunnen ontstaan. De wandstructuur moet voldoende zijn om ten
minste vier keer het gewicht van de gemonteerde apparatuur te ondersteunen.
Deze behuizing is enorm zwaar. Probeer nooit deze behuizing te verplaatsen of
op te tillen zonder hulp.
Kantelgevaar! Wanneer meerdere componenten uit deze behuizing steken,
bestaat de kans dat deze zal kantelen. Om dit risico te voorkomen, mag niet
meer dan één component uit de behuizing steken.

4
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Plaats geen voorwerpen op deze behuizing en stapel de behuizing niet op een
andere behuizing.
Houd vloeistof uit de buurt van deze behuizing.
Zorg dat u de behuizing installeert op een plaats die geschikt is voor het
gecombineerde gewicht van de behuizing en de apparatuur die u in de
behuizing wilt plaatsen.
Dit product vereist een geaarde verbinding. Gebruik dit product niet zonder een
geaarde verbinding.
Voordat u apparatuur aan dit product toevoegt, moet u er zeker van zijn dat u
dit product op de juiste manier in elkaar gezet heeft, correct geïnstalleerd heeft
en dat het aan een wand gemonteerd is.
Wanneer u dit product met apparatuur belast, moet de zwaarste apparatuur
als eerste in het onderste gedeelte van het product worden geplaatst. Ga door
met het plaatsen van de apparatuur in aopende volgorde, d.w.z. dat de lichtere
apparatuur bovenin dit product en de zwaardere onderin worden geïnstalleerd.
注意
最初に取扱説明書を最後まで読み、本製品の組み立て方をすべて理解してか
ら組み立て作業を始めて下さい。
壁面の構造は建物によって異なります。壁面の構造や使用する取り付け金具
が設置する装置を適切に支えられるかどうか、必ず確認してください。この注
意を怠ると、怪我をする恐れや器物破損の恐れがあります。設置する装置の少
なくとも4倍の重量に耐えられる壁面構造が必要となります。
本製品は、非常に重いエンクロージャです。絶対に一人で持ち上げたり動かし
たりしないで下さい。
転倒注意！本製品から複数のコンポーネントが突き出した状態にしておくとエ
ンクロージャが転倒する恐れがあります。転倒リスクを回避するために、エンク
ロージャからはコンポーネントが突き出ないようにして下さい。
本製品の上に何も載せないで下さい。複数のエンクロージャを重ねて設置し
ないで下さい。
液体物をエンクロージャに近づけないようにして下さい。
エンクロージャ自身と中に積載する装置の総重量に耐えられるエリアに設置
して下さい。

5
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
この製品にはアースが必要です。アース接続をしていない状態で本製品を使
用しないでください。
本製品に装置を積載する前に、組み立て、設置、壁面への取り付けが適切に行
われているか確認して下さい。
本製品に装置を積載する際は、最初に最も重い装置を一番下のセクションに
入れて下さい。重い装置から順に積載し、重いものが下のセクション、軽いも
のが上のセクションに配置されるようにして下さい。
Dichiarazioni di avvertenza
Leggere l’intero manuale e assicurarsi di aver compreso tutte le istruzioni prima
di iniziare ad assemblare e a utilizzare questo prodotto.
La struttura dei muri può variare. È quindi importante vericare che il tipo di
struttura e gli accessori di montaggio utilizzati sorreggano senza problemi
l’apparecchiatura montata. L’inosservanza di questa indicazione potrebbe
causare lesioni personali e/o danni all’apparecchiatura. La struttura del muro
dovrebbe essere in grado di sostenere un peso no a quattro volte superiore a
quello dell’apparecchiatura montata.
Il box esterno è molto pesante. Non tentare di spostarlo o sollevarlo senza
assistenza.
Pericolo di ribaltamento! L’estensione di più componenti dal box esterno
aumenta il rischio di ribaltamento del box esterno. Per evitare questo rischio,
non estendere più di un componente dal box esterno.
Non collocare oggetti sul box esterno e non impilare un box esterno sopra un
altro.
Tenere il box esterno lontano dai liquidi.
Assicurarsi di installarlo in un punto che possa sorreggere il peso combinato del
box esterno e dell’apparecchiatura che si intende collocare al suo interno.
Il prodotto richiede una messa a terra. Non utilizzare il prodotto in assenza di
una messa a terra.
Prima di aggiungere un’apparecchiatura al prodotto, vericare di averlo
assemblato, installato e montato correttamente a una parete.
Quando si caricano le apparecchiature all’interno del prodotto, partire da
quelle più pesanti collocandole nella parte inferiore del prodotto. Continuare

6
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
l’operazione in ordine decrescente di peso, in modo che le apparecchiature più
leggere siano installate nelle parti superiori del prodotto e quelle più pesanti
nella parte inferiore.
Avertissements
Assemblez ce produit conformément aux instructions.
Lisez tout le manuel et assurez-vous que vous comprenez les instructions avant
de commencer à assembler et utiliser ce produit.
Les structures des murs varient. Vous devez impérativement vérier que le
type de mur et le matériel de xation que vous utilisez permettent de soutenir
correctement l’équipement. Dans le cas contraire, vous risquez de vous blesser
ou d’endommager le matériel. La structure du mur doit pouvoir supporter au
moins quatre fois le poids de l’équipement monté.
Ce rack de serveur est extrêmement lourd. Ne tentez jamais de le déplacer ou de
le soulever sans aide.
Risque de basculement! L’extension de plusieurs composants à partir du rack de
serveur augmente le risque de basculement. Pour éviter ce risque, n’étendez pas
plus d’un composant à partir du rack de serveur.
Ne placez aucun objet sur ce rack de serveur et n’empilez pas le rack sur un
autre rack.
N’approchez aucun liquide du rack de serveur.
Veillez à installer le rack de serveur dans un endroit pouvant supporter le poids
combiné du rack et des équipements que vous comptez placer à l’intérieur.
Ce produit nécessite un raccordement à la terre. N’utilisez pas ce produit sans
raccordement à la terre.
Avant d’ajouter des équipements à ce produit, vériez que vous l’avez
correctement assemblé, installé et xé au mur.
Lorsque vous chargez des équipements dans ce produit, chargez les
équipements les plus lourds dans la partie inférieure du produit en priorité.
Continuez de charger les équipements dans un ordre de poids décroissant,
de sorte que les équipements les plus légers soient installés dans les parties
supérieures du produit, et les éléments plus lourds dans les parties inférieures.

7
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Mensagens de aviso
Leia todo o manual e certique-se de que entende as instruções antes de
começar a montar e a utilizar este produto.
As estruturas de parede variam e é importante certicar-se de que o tipo de
estrutura de parede e hardware de montagem que está a usar irá suportar
devidamente o equipamento montado. O incumprimento pode resultar
em ferimentos pessoais e/ou danos no equipamento. A estrutura de parede
deve ser capaz de suportar pelo menos quatro vezes o peso do equipamento
montado.
Esta caixa é extremamente resistente. Nunca tente mover ou levantar esta caixa
sem assistência.
Perigo de queda! Estender vários componentes desta caixa aumenta a
probabilidade desta caixa cair. Para evitar este risco, não expandir mais de um
componente desta caixa.
Não colocar nenhum artigo nesta caixa e não empilhar a caixa em cima de outra
caixa.
Manter líquidos afastados desta caixa.
Certique-se de que instala a caixa numa área que pode suportar o peso
combinado da caixa e o equipamento que pretende colocar dentro da caixa.
Este produto requer uma ligação à terra. Não utilize este produto sem uma
ligação à terra.
Antes de adicionar equipamento a este produto, certique-se de que
estruturou, instalou e montou devidamente o produto a uma parede.
Quando carregar equipamento neste produto, carregue primeiro o
equipamento mais pesado na secção inferior deste produto. Continue a carregar
equipamento numa ordem descendente de peso, de forma a que o peso mais
leve seja instalado nas secções superiores deste produto e os artigos mais
pesados estejam no fundo.
Advertencias de uso
Lea todo el manual y asegúrese de haber comprendido bien las instrucciones
antes de proceder con el ensamblaje y el uso de este producto.
Las estructuras de una pared pueden variar, por lo que es importante
determinar con certeza el tipo de estructura de la pared y el hardware de

8
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
montaje que se va a utilizar para soportar debidamente el equipo. De lo
contrario, se pueden producir lesiones personales o daños del equipo. La
estructura de la pared debe ser capaz de soportar al menos cuatro veces el peso
del equipo instalado.
La caja es extremadamente pesada. Nunca intente mover o alzar esta caja sin la
debida asistencia de otra persona.
¡Peligro de vuelco! Añadir a esta caja varios componentes aumenta las
posibilidades de peligro de vuelco de la caja. Para evitar dicho riesgo, no añada
más que un solo componente.
No coloque ningún elemento encima de la caja y no apile la caja encima de otra
caja.
Mantenga cualquier líquido lejos de la caj
Asegúrese de instalar la caja en un área que tenga capacidad para soportar el
peso combinado de la caja y el equipo que va a instalar dentro de la misma.
Este producto requiere conexión a tierra. No utilice este producto sin conexión
a tierra.
Antes de instalar equipos en este producto, asegúrese de haberlo ensamblado e
instalado correctamente en una pared.
Cuando instale equipo en este producto, coloque primero el equipo más
pesado en la parte inferior. Continúe con la instalación de más equipos en orden
descendente de peso, a n de que el equipo más liviano quede instalado en la
parte superior y el más pesado en la parte inferior.
Warnhinweise
Bevor Sie dieses Produkt montieren und verwenden, lesen Sie das gesamte
Handbuch und vergewissern Sie sich, dass Sie die Anweisungen verstanden
haben.
Wandkonstruktionen können variieren, daher ist es wichtig sicherzustellen,
dass die Art der Wandkonstruktion und das verwendete Montagezubehör
zur ordnungsgemäßen Montage der Geräte geeignet sind. Andernfalls kann
es zu Verletzungen und/oder zur Beschädigung des Produkts kommen. Die
Wandkonstruktion sollte mindestens das vierfache Gewicht der montierten
Geräte tragen können.
Dieses Gehäuse ist extrem schwer. Versuchen Sie niemals, dieses Gehäuse ohne

9
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Hilfe zu bewegen oder anzuheben.
Kippgefahr! Das Ausziehen mehrerer Komponenten aus diesem Gehäuse erhöht
die Chance, dass das Gehäuse umkippt. Um dies zu vermeiden, ziehen Sie
niemals mehr als eine Komponente aus diesem Gehäuse aus.
Platzieren Sie keine Gegenstände auf dem Gehäuse und stapeln Sie das
Gehäuse nicht auf einem anderen Gehäuse.
Halten Sie Flüssigkeiten von diesem Gehäuse fern.
Vergewissern Sie sich, dass der Untergrund, auf dem das Gehäuse aufgestellt
wird, in der Lage ist, das Gesamtgewicht des Gehäuses und der Geräte, die Sie
darin platzieren möchten, zu tragen.
Dieses Produkt erfordert einen Schutzleiteranschluss. Verwenden Sie das
Produkt nicht ohne einen Schutzleiteranschluss.
Vergewissern Sie sich, dass Sie das Produkt ordnungsgemäß montiert, installiert
und an einer Wand befestigt haben, bevor Sie Geräte hinzufügen.
Achten Sie beim Beladen des Produkts mit Geräten darauf, zunächst das
schwerste Gerät an der untersten Stelle des Produkts zu platzieren. Platzieren
Sie die Geräte anschließend in absteigender Reihenfolge nach ihrem Gewicht,
sodass leichtere Geräte in den oberen Abschnitten dieses Produkts installiert
werden und die schwereren Geräte sich unten benden.

10
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Table of Contents
Warning Statements ..............................................................................2
Product Diagram ....................................................................................11
Product Information .............................................................................12
Package Contents ..................................................................................................................................... 12
Requirements ............................................................................................................................................. 12
Grounding the Wall-Mount Enclosure ................................................13
Locking or Unlocking the Front Door .................................................14
Removing the Side Panels ....................................................................14
Replacing the Side Panels.....................................................................15
Removing the Cable Access Cover ......................................................15
Replacing the Cable Access Cover.......................................................16
Reversing the Front Door......................................................................17
Adjust the Depth of the Mounting Rails.............................................18
Use the Mounting Rail Tapped Holes..................................................19
Mount the Enclosure to the Wall .........................................................20
Installing Equipment .............................................................................21

11
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Product Diagram
1Front Door 5Cable Access Openings
(x 2)
2Side Panels (x 2) 6Mounting Plate
3Vents 7Top Panel
4Cable Access Covers (x 2) 8Bottom Panel
1
2
23
3
4
4
5
5
6
7
8

12
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Product Information
Package Contents
• Wall-Mount Enclosure x 1
• 1U Shelf (CABSHELFV1U) x 1
• Roll of Hook-and-Loop Fastener x 1
• 12-24 Cage Nuts x 24
• 12-24 Screws x 24
• Door Keys x 2
• Side Panel Keys x 2
• Cup Washers x 24
• User Manual x 1
Requirements
• Phillips™ type screwdriver
• Appropriate tools and mounting hardware for the type of
wall you’re using
Note: The images in this manual depict RK920WALM. This
product features a dierent rack height and depth, and has
two posts instead of four.

13
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Grounding the Wall-Mount Enclosure
Warning! This product must be grounded. Do not use this
product without an earth ground connection.
1. Use an M6 Screw to attach a Grounding Wire to the front or
rear Grounding Point on the Wall-Mount Enclosure.
Installing the Grounding Wire
2. Route the Grounding Wire under the frame of the Wall-
Mount Enclosure and connect the Grounding Wire to your
facility’s earth ground connection.

14
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Locking or Unlocking the Front Door
• To lock or unlock the front door of the enclosure, insert one
of the provided Door Keys in the Lock on the Front Door on
the Wall-Mount Enclosure and turn the key clockwise or
counterclockwise.
Removing the Side Panels
1. If the Side Panels are locked, use one of the provided Side
Panel Keys to unlock the Side Panels.
2. Pull the two Tabs on the Side Panel towards the center of
the panel.
Side Panel Tabs

15
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
3. While pulling the two Tabs, lift the Side Panel free from the
Wall-Mount Enclosure. Be careful and use proper lifting
techniques when removing the Side Panels from the Wall-
Mount Enclosure.
4. Repeat steps 1 to 3 to remove the other Side Panel.
Replacing the Side Panels
1. Place one of the Side Panels in the groove at the bottom of
the Wall-Mount Enclosure.
2. Pull the two Tabs on the Side Panel towards the center of
the panel.
3. Push the top part of the Side Panel into the Wall-Mount
Enclosure and release the Tabs.
4. Use one of the provided Side Panel Keys to lock the Side
Panel.
Removing the Cable Access Cover
Both the top and bottom panels of the enclosure have cable
access covers that you can remove to access and manage your
cables.
1. Use a Phillips Head Screwdriver to remove the four Screws
securing the Cable Access Cover.

16
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
2. Pull the Cable Access Cover away from the Wall-Mount
Enclosure.
Removing the Cable Access Cover
Replacing the Cable Access Cover
1. Align the Cable Access Cover with the Cable Access
Opening.
2. Use a Phillips Head Screwdriver to insert the four Screws
through the Cable Access Cover and into the Wall-Mount
Enclosure.
3. Tighten the Screws, being careful not to over-tighten.

17
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Reversing the Front Door
To accommodate dierent rack congurations, you can reverse
the Front Door of the Wall-Mount Enclosure so that it opens
to the left or right of the Wall-Mount Enclosure. The Front
Door is attached to the Wall-Mount Enclosure with Levers
that are located at the top and bottom of the Front Door.
1. In the top corner of the inside of the Front Door, pull the
lever down and move the top corner of the Front Door away
from the Wall-Mount Enclosure.
2. In the bottom corner of the inside of the Front Door, pull
the lever up and remove the Front Door from the Wall-
Mount Enclosure.
Lever Location
3. Flip the Front Door so that the Levers are located on the
opposite side.
4. Position the Front Door so that the top and bottom Levers
are aligned with the washers located in the hinge area of the
Wall-Mount Enclosure.

18
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
5. In the top corner of the Front Door, pull the Lever down
and release it into the washer and hole in the Wall-Mount
Enclosure.
6. In the bottom corner of the Front Door, pull the Lever up
and release it into the washer and hole in the Wall-Mount
Enclosure.
Adjust the Depth of the Mounting Rails
The Mounting Rails come pre installed in the Wall-Mount
Enclosure. The Mounting Rails can be adjusted independently
in 3/4 inch (20 mm) increments to accommodate dierent sizes
of equipment.
Warning! Remove all equipment before adjusting the
Mounting Rails.
1. Use a Phillips Head Screwdriver to remove the Screw and
Cage Nut located in the upper and lower corners of the
Mounting Rails.
2. Install the Cage Nuts at the desired depth, along the upper
and lower Mounting Rails.
3. Slide the Mounting Rail to the depth of the Cage Nuts and
use a Phillips Head Screwdriver to install and tighten the
Screws that you removed in step 1.

19
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Adjusting the Mounting Rails
Use the Mounting Rail Tapped Holes
The Mounting Rails come pre installed with the Cage Nut
Holes facing outward. However, the Mounting Rails can be
adjusted so that you can use the Tapped Holes to install your
equipment.
Warning! Remove all equipment before adjusting the
Mounting Rails.
1. Use a Phillips Head Screwdriver to remove the Screw and
Cage Nut located in the upper and lower corners of the
Mounting Rails.
2. Change the location of the Mounting Rails so that the sides
of the Mounting Rails with the Tapped Holes are facing the
Front Door.