StarTech.com S251BU31REMD User manual

Quick-start guide
FR: Guide de l’utilisateur - fr.startech.com
DE: Bedienungsanleitung - de.startech.com
ES: Guía del usuario - es.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
PT: Guia do usuário - pt.startech.com
IT: Guida per l’uso - it.startech.com
Manual Revision: 03/07/2017
For the latest information, technical specications, and support for
this product, please visit www.StarTech.com/S251BU31REMD.
Package contents
• 1 x 2.5” SATA enclosure
• 1 x USB-C to Micro-B cable
• 1 x USB-A to Micro-B cable
• 4 x drive-mounting screws
• 1 x quick-start guide
Requirements
• 2.5” SSD or HDD
• Screwdriver
The S251BU31REMD is OS independent and doesn’t require any
additional drivers or software.
Note: The S251BU31REMD is designed to be used with the
S251BU31REM mobile backplane available at www.StarTech.com.
Requirements are subject to change. For the latest requirements,
please visit www.StarTech.com/S251BU31REMD.
S251BU31REMD
2.5” SSD/HDD Removable Enclosure - USB 3.1 (10Gbps)
*actual product may vary from photos
Introduction
The S251BU31REMD is a portable drive enclosure that enables
you to transport or store your drive. The portable drive enclosure
features USB 3.1 (10Gbps) connectivity, providing fast performance
and quick access to data.
Product diagram
Power LED
Activity
LED
SATA power connector
SATA data connector
USB 3.1 Micro-B port
Install a drive in the enclosure
Warning! Drives should be handled carefully, especially when
you transport them. If you’re not careful with your drives, you may
experience lost or corrupted data. Make sure that you’re properly
grounded by wearing an anti-static strap when you install any
computer component. If an anti-static strap isn’t available, touch a
large, grounded metal surface for several seconds to discharge any
built-up static electricity.
1. If the cover plate is installed, use a screwdriver (not provided)
to remove the Housing assembly screws from the end of the
enclosure and take o the cover plate.
2. Carefully pull the circuit board out of the enclosure.
3. Gently slide the connector on your drive into the corresponding
connectors on the circuit board.
4. Use the drive-mounting screws to attach the drive to the circuit
board.
5. Carefully slide the circuit board back into the enclosure.
6. Replace the cover plate on the enclosure, insert the Housing
assembly screws, and tighten them in place.
7. Connect one of the provided USB Micro-B cables to the USB 3.1
Micro-B port on the enclosure and your computer.
Housing assembly
screw
Housing assembly
screw

FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation. Changes or modications not expressly approved by StarTech.com could void the user’s authority to operate the
equipment.
Industry Canada Statement
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.
CAN ICES-3 (B)/NMB-3(B)
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s)
to which this manual applies by the third-party company in question. Regardless of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby acknowledges that all
trademarks, registered trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the property of their respective holders.
Technical Support
StarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and
access our comprehensive selection of online tools, documentation, and downloads.
For the latest drivers/software, please visit www.startech.com/downloads
Warranty Information
This product is backed by a two-year warranty.
StarTech.com warrants its products against defects in materials and workmanship for the periods noted, following the initial date of purchase. During this period, the products may be returned for
repair, or replacement with equivalent products at our discretion. The warranty covers parts and labor costs only. StarTech.com does not warrant its products from defects or damages arising from
misuse, abuse, alteration, or normal wear and tear.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors, employees or agents) for any damages (whether direct or indirect, special, punitive, incidental,
consequential, or otherwise), loss of prots, loss of business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product. Some states do not
allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations or exclusions contained in this statement may not apply to you.
About the LED indicators
The enclosure features a green Power LED and a red Activity LED.
LED behavior Signicance
The Power LED is illuminated The enclosure is receiving power
The Activity LED is blinking Drive is being accessed
Install the enclosure into a drive bay
If you’re installing the enclosure into a StarTech.com S251BU31REM
drive bay, complete the following:
• After you install a drive bay in your computer, carefully slide the
drive enclosure into the slot on the front of the drive bay.
To remove the drive enclosure, press the eject button on the drive
bay and pull out the enclosure.