StarTech.com SAT3510U2F User manual

SATA Hard Drive Enclosure
3.5” USB, FireWire to SATA
External Hard Drive Enclosure
SAT3510U2F
SAT3510U2FGB
Instruction Manual

FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.•
Increase the separation between the equipment and receiver.•
Connect the equipment into an outlet on a circuit different from that to which the receiver•
is connected.
Consult the dealer or an experienced radio/TV technician for help.•
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only
and do not represent an endorsement of a product or service by StarTech.com, or an
endorsement of the product(s) to which this manual applies by the third-party company
in question. Regardless of any direct acknowledgement elsewhere in the body of
this document, StarTech.com hereby acknowledges that all trademarks, registered
trademarks, service marks, and other protected names and/or symbols contained in this
manual and related documents are the property of their respective holders.

i
Table of Contents
Introduction..................................................................... 1
Packaging Contents.....................................................................1
System Requirements .................................................................1
Installation....................................................................... 2
Hardware Installation...................................................................2
Driver Installation.........................................................................3
Using the Enclosure ....................................................... 3
Specifications.................................................................. 5
Technical Support........................................................... 6
Warranty Information...................................................... 6

1
Introduction
The SAT3510U2F External Hard Drive Enclosure supports both
USB 2.0 and FireWire 400 (IEEE1394a) host connections in a slim,
lightweight aluminum design.
Packaging Contents
1 x SAT3510U2F/GB hard drive enclosure•
1 x USB A-B cable•
1 x 6-pin FireWire cable•
1 x Power Adapter•
1 x Screw kit•
1 x User Manual•
System Requirements
USB and/or FireWire enabled computer system with available port•
Microsoft Windows• ®2000/XP/Vista/7, Mac OS®9.2/10.x, or
Linux®

2
Installation
WARNING: Hard drives require careful handling, especially when be-
ing transported. If you are not careful with your hard disk, lost data may
result. Always handle your hard drive and storage device with caution.
Hardware Installation
Remove the two small screws from either side of the rear panel of1.
the enclosure and then remove the rear panel bezel. The drive tray
should now slide out from the front side.
Place a 3.5” SATA hard drive into the drive tray and then slide it into2.
the 7+15 SATA connector on the rear panel.
Fasten the hard drive to the drive tray from the sides with the3.
supplied hard drive screws.
Hard Drive Screws
Retaining Screws

3
Slide the hard drive tray back into the enclosure and place the reawr4.
panel bezel over the rear panel. Fasten the two side screws for the
rear panel bezel.
Connect the power adapter from the enclosure to an available power5.
outlet and then turn the enclosure on, via switch on the rear panel.
Connect the enclosure to the host computer system via FireWire or6.
USB cable.
Driver Installation
Windows 2000/XP/Vista/7, Mac OS 9.2/10.x, or Linux/Unix
No driver installation is required for these operating systems, as this
enclosure is natively supported, so the drivers are already installed.
Retaining Screws

4
Using the Enclosure
Windows 2000/XP/Vista/7
If you are using a brand new hard drive that does not contain any data,
then you will first need to prepare the hard drive for use. From the
main desktop, right-click on “My Computer” (“Computer” in Vista), then
select Manage. In the new Computer Management window, select Disk
Management from the left window panel.
Locate the Disk that says it is “Unallocated” (check hard drive capacity
to confirm it’s the correct hard drive) and then right-click in the section
that says “Unallocated” and select “New Partition”.

5
The New Partition Wizard will appear. Follow the instructions in the
wizard to complete setting up the drive. Once complete, the Disk
should show up as “Healthy” with a drive letter assigned (ie. E:). This
drive letter should now appear within My Computer.
If you are installing a hard drive that already has data on it, then after
plugging it in, the drive should automatically show up with a drive letter
assigned within My Computer.

6
Specications
Bus Interface USB 2.0
FireWire400 (IEEE1394a)
Connectors
1 x USB type B
2 x 6-pin FireWire
1 x DC power connector
LEDs 1 x Power/Activity
Chipset Oxford OXUF934SSA
Hard Drive Support 3.5” SATA 1.5/3.0Gbps,
up to 2TB in capacity
Maximum Data Transfer Rate USB: 480Mb/s
FireWire: 400Mb/s
Power Adapter 12VDC, 2A, center positive,
type N plug
Dimensions 208.0mm x 118.0mm x 30.0mm
Weight 400g
Compatible Operating
Systems
Windows 2000/XP/Vista/7,
Mac OS 9.2/10.x, Linux/Unix

7
Technical Support
StarTech.com’s lifetime technical support is an integral part of our
commitment to provide industry-leading solutions. If you ever need
help with your product, visit www.startech.com/support and access
our comprehensive selection of online tools, documentation, and
downloads.
Warranty Information
This product is backed by a one year warranty.
In addition, StarTech.com warrants its products against defects in
materials and workmanship for the periods noted, following the initial
date of purchase. During this period, the products may be returned
for repair, or replacement with equivalent products at our discretion.
The warranty covers parts and labor costs only. StarTech.com does
not warrant its products from defects or damages arising from misuse,
abuse, alteration, or normal wear and tear.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA
LLP (or their officers, directors, employees or agents) for any damages
(whether direct or indirect, special, punitive, incidental, consequential, or
otherwise), loss of profits, loss of business, or any pecuniary loss, arising
out of or related to the use of the product exceed the actual price paid
for the product. Some states do not allow the exclusion or limitation of
incidental or consequential damages. If such laws apply, the limitations
or exclusions contained in this statement may not apply to you.