StarTech.com 8 Port StarView CAT5 UTP KVM User manual

StarView CAT5 UTP KVM
8 Port StarView CAT5 UTP KVM
16 Port StarView CAT5 UTP KVM
Instruction Manual
*8 Port Model Shown

FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turn-
ing the equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
Reorient or relocate the receiving antenna.•
Increase the separation between the equipment and receiver.•
Connect the equipment into an outlet on a circuit different from that to which the receiver•
is connected.
Consult the dealer or an experienced radio/TV technician for help.•
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected
names and/or symbols of third-party companies not related in any way to StarTech.com.
Where they occur these references are for illustrative purposes only and do not represent an
endorsement of a product or service by StarTech.com, or an endorsement of the product(s)
to which this manual applies by the third-party company in question. Regardless of any direct
acknowledgement elsewhere in the body of this document, StarTech.com hereby acknowl-
edges that all trademarks, registered trademarks, service marks, and other protected names
and/or symbols contained in this manual and related documents are the property of their
respective holders.

Instruction Manual
i
Instruction Manual
Table of Contents
Safety Precautions ....................................................................... iii
Introduction.................................................................................... 1
Features ......................................................................................1
Package contents ........................................................................1
Hardware Guide ............................................................................. 2
Installation...................................................................................... 6
Stacking Switches and Rack Mounting .......................................6
Single Station Installation ............................................................8
Server Interface Module Installation............................................10
SV5PS2S (PS2 Module)..............................................................10
SV5USBS (USB Module) ............................................................10
Daisy Chaining ............................................................................11
Daisy Chain Installation Diagram ................................................12
Basic Operation............................................................................. 13
Port Selection ..............................................................................13
Hot Plugging................................................................................13
Powering Off and Restarting .......................................................14
Port ID Numbering.......................................................................15
OSD Operation............................................................................... 15
Overview......................................................................................15
OSD Navigation...........................................................................17
OSD Main Screen Headings .......................................................17
OSD Functions ............................................................................17
Hotkey Operation........................................................................... 27

Instruction Manual
ii
Hotkey Port Control .....................................................................27
Auto Scanning .............................................................................28
Skip Mode....................................................................................29
Hotkey Beeper Control.................................................................. 30
Hotkey Summary Table................................................................30
Keyboard Emulation...................................................................... 32
Mac Keyboard..............................................................................32
Sun Keyboard..............................................................................33
Firmware Upgrades....................................................................... 34
Introduction..................................................................................34
Performing the Upgrade ..............................................................35
Server Interface Module Upgrade ................................................ 37
Performing the Upgrade ..............................................................38
Firmware Upgrade Recovery.......................................................39
Connection Tables ......................................................................... 40
Administrator Login Failure ......................................................... 42
OSD Factory Default Settings ...................................................... 43
Specifications ................................................................................ 44
Technical Support........................................................................46
Warranty Information ...................................................................46

Instruction Manual
iii
Safety Precautions
The following precautions should be employed to ensure safe, reliable
operation of this device:
Read the enclosed instructions, and save them for future reference
Do not place the device on an unstable surface. If the device falls,•
serious damage will result
Follow all warnings and instructions marked on the device (if•
applicable)
Do not use the device near water•
Do not place the device near or over any device that produces heat (i.e.•
radiators, heat registers etc.)
To ensure adequate ventilation and reliable operation, never block the•
vent openings
Do not place the device on a soft surface (i.e. bed, carpet, etc.) as this•
will block ventilation openings. Similarly, never place the device in a
built-in enclosure unless adequate ventilation is provided
Never spill liquid of any kind on the device•
Unplug the device from the wall, prior to cleaning. Do not use liquid or•
aerosol cleaners, instead use a damp cloth
The device should be operated from the type of power source indicated•
on the marking label. If you are unsure of the type of power available,
please contact your local power company
The device is equipped with a 3-wire grounding type plug. This is a•
safety feature that should be left intact at all times. If you are unable to
insert the plug into the outlet, contact your electrician to replace the
available (outdated) outlet. Do not attempt to defeat the purpose of or
bypass the grounding-type plug; always follow local wiring codes
Position system cables and power cables carefully. Do not allow•
anything to rest on the power cord or cables. Route the power cord
and cables so that they cannot be stepped or tripped on
If an extension cord is used with this device, make sure that the•

Instruction Manual
iv
combined ampere rating of all products used on the cord does not
exceed the extension cord ampere rating. Make sure that the total of
all devices connected to the wall outlet does not exceed 15 amperes
To help protect your system from sudden, transient increases and•
decreases in electrical power, use a surge suppressor, line conditioner
or Uninterruptible Power Supply (UPS)
Follow all warnings and instructions marked on the device (if•
applicable)
When connecting or disconnecting power to hot pluggable power•
supplies, observe the following guidelines:
Install the power supply before connecting the power cable to the
power supply
Unplug the power cable before removing the power supply
If the system has multiple sources of power, disconnect power by
unplugging all power cables from the power supplies
Never push objects of any kind into or through cabinet slots. They
may touch dangerous voltage points or short out components,
risking fire or electrical shock.
Do not attempt to service the device yourself. Please refer all servicing•
to qualified service personnel
Unplug the device from the wall outlet, and consult with a qualified•
service technician, if any of the following conditions occur:
The power cord is frayed or damaged
Liquid has been spilled into the device, or the device has been
exposed to rain or water
The device has been dropped, or the casing has been damaged
The device exhibits a distinct decline in performance, indicating a

Instruction Manual
v
need for service
The device does not operate normally, when following the operating
instructions
Only adjust controls that are described in the following operating•
instructions. Improper adjustment of other controls may result in
damage that could lead to extensive repair

Instruction Manual
1
Introduction
Thank you for purchasing a StarTech.com CAT 5 KVM switch. Allowing
control of up to 8 (SV831DUTP) or 16 (SV1631DUTP) computers over a
CAT 5 cable connection (between the switch and the slave computers),
this device provides a cost-effective solution that’s simple to install, and
equally easy to configure and control through pushbutton operation, hot-
key commands or the convenient On-Screen Display.
Features
Auto-scan function automates sequential computer selection•
Cascade configuration expands system capability up to 256 computers•
(SV831DUTP) or 512 computers (SV1631DUTP)
Allows for easy computer selection using front panel pushbuttons,•
hotkeys and intuitive On-Screen Display
Hot Pluggable - add or remove computers without having to power•
down the switch
Package contents
1 x StarView CAT5 KVM Switch
1 x User Manual
1 x Power Adapter
1 x Mounting Bracket Kit
1 x Firmware Upgrade Cable
Please note that when accessing the Switch, you will be asked to supply
a Username and Password.
In the Username field, press the Enter key on the connected keyboard.
In the Password field, press the Enter key. You will then be logged into
the On Screen Display.

Instruction Manual
2
Hardware Guide
Front Panel View SV831DUTP
Front Panel View SV1631DUTP
1&2 734 5 6
1&2
3764 5
Please refer to the tables on pages 3 and 4 for descriptions
of the above illustrations.

Instruction Manual
3
Component Functions (Front Panel)
Component Description
1
Port
Selection
Switches
a. Press a switch to give the KVM focus to the
computer attached to its corresponding port.
b. Simultaneously pressing buttons 1 and 2 for 3
seconds performs a Keyboard and Mouse Reset.
c. Simultaneously pressing buttons 7 and 8 starts Auto
Scan Mode.
2 Port LEDs
The Port LEDs are built into the Port Selection Switches.
The upper ones are the On Line LEDs; the lower ones
are the Selected Port LEDs:
a. An On Line LED lights GREEN to indicate that the
computer attached to its corresponding port is up and
running. A flashing LED indicates that the Port is being
used for cascading to another switch.
b. A Selected LED lights ORANGE to indicate that the
computer attached to its corresponding port is the one
that has the KVM focus.
The LED is steady under normal conditions, but flashes
when its port is accessed under Auto Scan Mode.
3Reset
Switch
Pressing this switch in performs a system reset. Note:
The switch is recessed and must be pushed with a thin
object - such as the end of a paper clip, or a ballpoint
pen.
4
Firmware
Upgrade
Recovery
Switch
During normal operation and while performing a firmware
upgrade, this switch should be in the NORMAL position.
If a firmware upgrade operation does not complete
successfully, this switch is used to perform a firmware
upgrade recovery.