StarTech.com AP150WN1X1OD User manual

Manual Revision: 09/25/2014
For the most up-to-date information, please visit: www.startech.com
DE: Bedienungsanleitung - de.startech.com
FR: Guide de l'utilisateur - fr.startech.com
ES: Guía del usuario - es.startech.com
IT: Guida per l'uso - it.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
PT: Guia do usuário - pt.startech.com
AP150WN1X1OD / AP150WN1X1OE / AP150WN1X1OG
Outdoor 150Mbps Wireless N Access Point -
1T1R 2.4GHz
*actual product may vary from photos

Instruction Manual
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment o and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference that may cause undesired
operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio
exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage, et
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d’en compromettre le fonctionnement.
IC Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limit set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator and your body.
Déclaration d’exposition à la radiation:
Cet équipement respecte les limites d’exposition aux rayonnements IC dénies pour un
environnement non contrôlé. Cet équipement doit être installé et mis en marche à une distance
minimale de 20 cm qui sépare l’élément rayonnant de votre corps.
L’émetteur ne doit ni être utilisé avec une autre antenne ou un autre émetteur ni se trouver à leur
proximité.
FCC ID: VYTLP-9318A
IC: 11232A- AP150WN1X1O

Instruction Manual
3
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and do not
represent an endorsement of a product or service by StarTech.com, or an endorsement of the
product(s) to which this manual applies by the third-party company in question. Regardless
of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby
acknowledges that all trademarks, registered trademarks, service marks, and other protected
names and/or symbols contained in this manual and related documents are the property of
their respective holders.
Important Notice
This product MUST be installed by a professional installer who is familiar with local building
and safety regulations, where appropriate, and is licensed by applicable authorities. The
professional installer is responsible for making sure grounding is available and that it meets
the relevant local and national electrical codes. Failure to employ a professional installer may
render the product warranty void and it may also expose the end user or service provider to
legal and nancial liabilities. StarTech.com expressly disclaims any and all liabilities for injury,
damage, or violation of regulations due to improper installation of outdoor units or antennas.
Always remember to protect the AP by installing grounding lines as it is necessary to protect
your outdoor installations from lightning strikes and the build-up of static electricity. The AP
must be grounded properly before powering up, as direct grounding of an outdoor AP is
critical and must be done correctly to protect your networks from harsh outdoor environments
and destructive ESD surge.
CAUTION: Be sure that earth grounding is available and that it meets local and national
electrical codes. If in doubt always consult with a qualied electrician to make sure the outdoor
installation is properly grounded. For additional lightning protection, lightning rods, lightning
arrestors or RJ45 surge protectors may be used to compliment the installation.

Instruction Manual
i
Table of Contents
Product Diagram ....................................................................................1
Rear View...................................................................................................................................................... 1
Introduction............................................................................................2
Packaging Contents ................................................................................................................................. 2
System Requirements.............................................................................................................................. 2
Connection Ports....................................................................................3
LED Indicators............................................................................................................................................. 4
Installation ..............................................................................................4
Preparing Your Site ................................................................................................................................... 4
Hardware Installation............................................................................5
Operation ................................................................................................6
Advanced Conguration ........................................................................................................................ 8
Wireless Settings ....................................................................................................................................... 9
Smart Features ........................................................................................................................................... 14
IP Settings .................................................................................................................................................... 16
Management Settings............................................................................................................................. 17
Password Settings (recommended) ................................................................................................... 18
Specications..........................................................................................19
Technical Support ..................................................................................20
Warranty Information............................................................................20

Instruction Manual
1
Product Diagram
Rear View
LED Panel
Pole/Wall
Mount Bracket
Interface Cover

Instruction Manual
2
Introduction
Packaging Contents
• 1 x Outdoor Access Point
• 1 x PoE Injector
• 1 x Metal Hose Clamp
• 1 x Power Adapter
• 1 x Quick Start Guide (CD)
System Requirements
• A networked computer system with a Java-enabled web browser (for conguration)
• Cat 5 (or better) network cabling from PoE Injector to Wireless AP and PoE Injector
to LAN Switch/router (no more than 100m total)
• Mounting screws / anchors if wall mounting PoE Injector and/or Wireless AP

Instruction Manual
3
Connection Ports
Interface Description
External Antenna
External RP-SMA Antenna connector (optional).
Upgradable to high gain antennas for more range. See
the External Antenna conguration section for setup
procedures.
PoE Port
Power over Ethernet RJ-45 port used to connect the
Access Point to the included PoE Injector for power and
data connectivity.
LAN Port (secondary) RJ-45 port used to connect additional network devices to
the Access Point.
External Antenna
(optional)
PoE Port LAN Port
(Secondary)

Instruction Manual
4
Indicator State Description
PWR ON The device is powered on
O The device is powered o
Wi activity Flashing Data is being transmitted / received over wireless
O No link detected
PoE
ON Link detected
O No link detected
Flashing Data is being transmitted / received on the PoE LAN
interface
LAN
ON Link detected
O No link detected
Flashing Data is being transmitted / received on the Secondary
LAN interface
LED Indicators
Installation
Preparing Your Site
1. Determine the location for the included PoE injector and mount using the
appropriate screws/anchors for the material you are mounting to (not included).
2. Determine the location for the Wireless AP. If you are pole-mounting the AP, use
the included clamp to secure the device. If you are wall mounting the AP, use the
appropriate screws/anchors for the material you are mounting to (not included).
3. Prepare/purchase the required length of Ethernet cabling to go from the PoE
Injector to your LAN Switch or router, and from PoE Injector to the AP.
Note: The total length of Ethernet cabling from the Wireless AP to your LAN switch or
router should not exceed 100m.

Instruction Manual
5
Hardware Installation
1. Connect the included power adapter to an available wall outlet and the DC jack on
the PoE injector.
2. Connect an Ethernet cable from the LAN port of the PoE Injector to your LAN switch
or router.
3. Connect a second Ethernet cable from the PoE port of the PoE Injector, the other
end of this cable will connect to the AP as instructed in the following steps.
4. Slide the bottom cover of the unit down to remove it and expose the ports.
5. Connect the Ethernet cable from the PoE port of the PoE Injector, to the PoE Port
port on the AP (closest to the antenna connector).
6. Slide the cover back on as shown.
Note: the AP may take approximately up to 2 mins to complete the power on
sequence.

Instruction Manual
6
Operation
Default Settings
SSID: AP150WN1X1OD
Security: None
Default IP Address: 192.168.1.200
ID: admin; PW: admin
DHCP: Auto
1. Scan for available wireless networks on your PC and connect to the
AP150WN1X1OD network
2. Open a web browser and enter the IP address 192.168.1.200 into the address bar,
then press Enter.
3. When the web menu appears, click the Start button at the bottom of your screen to
begin the Setup Wizard. The wizard will guide you through the following basic setup
options:
a. System Clock
b. Network Name (wireless SSID)
c. Network Security
System Clock
The System Clock is used for system logs and setting schedules for Internet access.
Click the Sync button to synchronize the System Clock with the time on your computer,
or set manually.
Click Next to continue
Before operation, it is recommended that you ensure the Access Point is using the latest
rmware version. Check www.startech.com/downloads for the latest rmware version.

Instruction Manual
7
Network Name
The default SSID of your Wireless Network is: AP150WN1X1OD
To change it, enter your desired name in the SSID eld. Users connecting wirelessly to
the Access Point will use this ID to identify your wireless network.
Click Next to continue
Network Security
By default, there is no Security Key congured on the Access Point. Enter your desired
security key (WPA) in the Security Key eld (recommended).
Note: The key must be at least 8 characters long
Click Next to apply your settings. The Access Point will reboot and may take up to
2 minutes. Please do not refresh the web page; it will automatically reload with the
Setup Summary page with the details of what has been congured.

Instruction Manual
8
Advanced Conguration
The following sections outline the advanced conguration settings available on the
Access Point. These options can be accessed by clicking the More Settings link from
the left side of the page, or by clicking the Finish button at the bottom of the Setup
Summary page.

Instruction Manual
9
Wireless Settings
Basic
The Wireless Basic Settings page allows you to adjust the settings for your wireless
network. These settings are for adjusting the Access Point after you have already gone
through the Smart Setup Wizard and wish to further adjust your congurations.
Disable Wireless LAN Interface:
Turns o all wireless access.
Band:
Allows you to setup access under a specic combination of Wi-Fi speed standards.
Broadcast SSID:
Disabling the broadcasting of your SSID will make it so outside users cannot see your
network when they scan for wireless networks - users must manually enter the SSID to
connect.
Data Rate:
Adjust the speed of your wireless network. It is recommended that you use Auto for
this selection.
SSID of Wireless network:
This is the name of your Wireless network and the name that users will scan for to
connect wirelessly.

Instruction Manual
10
Multiple AP:
You may add one additional (SSID) to you Wireless network. The additional SSID can
have its own security, band and data rate settings. You may restrict users for specic
SSIDs or provide access only to some users with lower bandwidth by changing the
band (i.e. only allow 802.11b access to specic users).
Channel Width:
Wi-Fi operates in two separate channel widths, 20Hz and 40Hz. 20Hz allows operation
on channels 1-11, while 40Hz is 5-11. 40Hz allows for faster speeds. Select the channel
width you wish to use for your network.
Control Sideband:
This relates to the channel number used for your wireless network. An upper band
represents higher channels and vice versa.
Channel Number:
The channel number used for your wireless network. If there are other wireless
networks using the same channel, this may cause slower performance. You may adjust
the channel here to attempt to improve performance through less interference.
WMM:
Prioritizes audio and video content going over your wireless network.
Associated Clients:
Displays all wireless connections to the Pro Access Point.
Security
Wireless security allows you to change the security type, password/key and format for
your wireless network. The security key you select must be used by all computers and
devices connecting to the Access Point wirelessly.

Instruction Manual
11
Using the drop down menu, you can select which network you wish to congure
and adjust the security settings for (standard wireless network or the multiple SSID
network).
Note: It is recommended to use WPA or WPA2 as your encryption type. WEP 64bit
and 128bit security is a more primitive WiFi security encryption type which may limit
wireless performance and speed from the Access Point. (Pre Service Pack 3 Windows
XP computers may not support WPA2).
Wi-Fi Protected Setup (WPS)
WPS is a Wi-Fi feature created to make Wi-Fi setup simpler and easier. Some wireless
devices and adapters support this feature with varying names (i.e. one touch setup or
WPS). You may enable WPS setup here by selecting the type of WPS setup you wish to
use. Push button
You may push the WPS button on the web menu. The Access Point does not have a
physical WPS button.

Instruction Manual
12
WDS Settings
Wireless Distribution System (WDS) allows you to use the Access Point to wirelessly
connect to other Access Points. In WDS mode, the Access Point can function as a Main
Access Point which is connected to a network using a cable, or it can be a Relay Access
Point which is wirelessly connected to the Main Access Point.
To congure WDS mode you will need to adjust the settings for the following elds:
a) Enable WDS: First you must enable the WDS function to use it.
b) MAC Address: Enter the MAC address of the Access Point that you wish to connect
to. If you are conguring the Main Access Point then you would need to enter the
Relay Access Point’s MAC Address here.
c) Comment: Provide a comment, such as “Main Access Point” to easily remember
which Access Point belongs to which MAC Address entry.
d) Band: Select the wireless band you wish to operate on.
e) Wireless Network (SSID): Enter the wireless SSID of your Access Point. Do not use the
same SSID for two separate Access Points.

Instruction Manual
13
f) Channel: Ensure that all Access Points, Main or Relay, operate on the same wireless
channel.
g) DHCP: WDS mode requires that you have a static IP address for your Access Point.
Enter a static IP address for your Access Point by selecting “Disable”under the DHCP
eld.
h) IP Address: The IP address of the Access Point should be on the same subnet as the
Main or Relay Access Points. For example, if the network you are connected to has
an IP address range of 192.168.1.100 – 192.168.1.200, then the IP address of the
Access Point should be 192.168.1.1xx.
i) Subnet Mask: The subnet mask for the Access Point should be the same as the
network you are connecting to. (e.g. 255.255.255.0)
j) Default Gateway: This entry is typically the IP address of your network router. (e.g.
192.168.1.1)
Antenna Settings
The Access Point includes an internal High Gain Antenna, however if you wish to use
an external antenna instead, you may activate the External Antenna port here. The
External Antenna Port is a RP-SMA port and accepts RP-SMA antenna connections. It is
compatible with most high gain antennas.
Note: It is important that you attach the external antenna to the External Antenna Port
BEFORE activating the External Antenna Port to avoid damage to the Access Point.
After you have attached the external high gain antenna, select the External Antenna
selection under Active Antenna and click Apply. After the Access Point reboots, your
external antenna will be active and ready for use.

Instruction Manual
14
Advanced Settings
These settings allow you to control the advanced details of your wireless network
conguration. Please use caution in changing these settings.
Smart Features
The Access Point provides Smart Features that oer convenience and protection for
your wireless network. The Smart Features allow you to control access to your wireless
network through on/o schedules, specic user authorizations, as well as through the
range of your wireless coverage for your.
Note: These settings only apply to users connecting through the Access Point to your
network.
Access Schedule
Set a schedule for when your Wi-Fi is enabled or disabled through the Access Schedule
feature.
Note: Ensure your Time Zone Settings have been congured in order for your schedule
to work correctly. Time Zone Settings can be adjusted from the web menu under
Management > Time Zone Settings.

Instruction Manual
15
To do so:
a) Click Enable Access Schedule
b) Select which days you wish for your Wi-Fi to be available
c) Select the time frame during that day that you wish for Wi-Fi to be available
d) Apply Changes
User Access Control
User Access lets you deny / allow access to specic users connecting wirelessly to your
network by MAC address. By inputting the MAC address(es) into this area, you can
dene whether that device is allowed into your network or not allowed. When entering
the MAC addresses, only enter alpha-numerical characters (e.g. A1B233C45566).
Wireless Coverage Controls
Adjust the output power of the Access Point to control the coverage distance of your
wireless network. For a smaller coverage area you can select a lower output power
percentage. For the maximum wireless coverage, select 100%.
Note: If you select a lower output power, your connection to your Home Network will
also decrease in range. So be sure to test your signal strength after each adjustment.

Instruction Manual
16
IP Settings
IP Address:
The IP address of the Access Point.
Subnet Mask:
The subnet of the Access Point.
Default Gateway:
The Access Point to another network, normally the IP address of your router.
DHCP:
The Access Point includes a ‘Smart’ AUTO DHCP feature to help manage the IP
addresses within your wireless network and with your router. When the Access Point is
connected to your home network/router through the ‘Network’ port, the AUTO DHCP
will determine whether it can receive an IP address from your router. If it can, it will
automatically switch to a client and allow your router to assign it an IP address.
When there is no connection available, the Access Point will act as a DHCP Server. You
may also manually control the IP settings of the Access Point by choosing Client, Server
or Disabled from the DHCP drop down menu.
DHCP Client Range:
The range of IP addresses the Access Point’s DHCP server will assign to devices
connecting to the Access Point.
Disabled / Static DHCP:
If your network requires the use of manual IP address assignments, select this option.
You may manually enter the IP address settings of the Access Point so it reects the
correct addresses to work with your specic network.