Steelman 65001 Owner's manual

JS Products, Inc. • 5440 S. Procyon St. • Las Vegas, NV 89118
Phone: [phone] • Fax: [phone] • www.steelmantools.com
LIMITED WARRANTY
STEELMAN ®JS Products, Inc. has carefully examined each product at the time of
manufacturing and warrants workmanship at the time of shipment. This warranty applies only
to the original consumer/purchaser and is not valid if the product is misused, or if accidental
damages occur. STEELMAN ®JS Products, Inc. assumes no direct or indirect liability for
incidental or consequential damages resulting from the use of its products. This warranty
commences on the date of the original consumer purchase, and extends for 90 Days
thereafter.
In the event of a defect or malfunction of a product, wherein repair or replacement should be
necessary, call the Customer Service Department at 1-800-255-7011 for complete
instructions on how to return the product for warranty repair or replacement. The original
consumer/purchaser must provide a copy of the Bill of Sale or Invoice showing the date on
which the purchase was made. After the (ninety) 90 Day Period, STEELMAN ®JS Products,
Inc. will charge a service charge for all parts and labor. Inbound and outbound freight will be
paid by the consumer/purchaser.
Some states do not allow limitations on how long an implied warranty lasts, so the above
limitation may not apply to you. Additionally, some states do not allow the exclusion or
limitation of incidental or consequential damages, so the above limitation may not apply
to you.
This warranty gives specific legal rights, and there may be other rights which vary from state
to state.
1) Install 9-volt battery in EngineEAR®control unit and attach headphone plug.
2) Turn On/Off switch to “Off” position before putting on headphones. Place headphones
firmly over ears, then turn the switch to “On”. Slowly increase volume to desired setting.
3) Place sensing tip flush on housing surface of suspect problem parts. By keeping the
sensing tip flush against the suspect part, outside noises are blocked. Use the metal
probe when working on hot or difficult to reach areas.
4) Use EngineEAR®to detect bad bearings and bushings, exhaust leaks, bad plug wires,
wind and water leaks, noisy valves and lifters or a squeak or rattle under the dash.
NOTE:
This device electronically amplifies sound and will provide clear sound around
most automobile parts. Static interference will occasionally occur around the coil
and distributor of most cars.
SPECIFICATIONS
65001
PART NO. DESCRIPTION
OPERATING INFORMATION
ADVANCED ELECTRONIC STETHOSCOPE
EngineEAR® EngineEAR®
Rev: 05/03/11
FRONT BACK BACK
COLOR SPECIFICATION:
1-COLOR
MATERIAL SPECIFICATION:
80 lb. Gloss Text
SIZE SPECIFICATION:
5.50"H x 8.50" W - FRONT AND BACK
Black =
100% Black
65001 - EngineEAR™ - STEELMAN
INSTRUCTION CARD
QTYDescription
KIT CONTENTS
Control Unit
Headphones
Rubber Sensor Tip
Metal Probe
1
1
1
1
411
HD-6060N
65012
413
Part No.
CAUTION:
It is against many state laws to operate
a motor vehicle while wearing headphones.
How to Use:

JS Products, Inc. • 5440 S. Procyon St. • Las Vegas, NV 89118
Phone: [phone] • Fax: [phone] • www.steelmantools.com
LIMITED WARRANTY
STEELMAN ®JS Products, Inc. has carefully examined each product at the time of
manufacturing and warrants workmanship at the time of shipment. This warranty applies only
to the original consumer/purchaser and is not valid if the product is misused, or if accidental
damages occur. STEELMAN ®JS Products, Inc. assumes no direct or indirect liability for
incidental or consequential damages resulting from the use of its products. This warranty
commences on the date of the original consumer purchase, and extends for 90 Days
thereafter.
In the event of a defect or malfunction of a product, wherein repair or replacement should be
necessary, call the Customer Service Department at 1-800-255-7011 for complete
instructions on how to return the product for warranty repair or replacement. The original
consumer/purchaser must provide a copy of the Bill of Sale or Invoice showing the date on
which the purchase was made. After the (ninety) 90 Day Period, STEELMAN ®JS Products,
Inc. will charge a service charge for all parts and labor. Inbound and outbound freight will be
paid by the consumer/purchaser.
Some states do not allow limitations on how long an implied warranty lasts, so the above
limitation may not apply to you. Additionally, some states do not allow the exclusion or
limitation of incidental or consequential damages, so the above limitation may not apply
to you.
This warranty gives specific legal rights, and there may be other rights which vary from state
to state.
1) Install 9-volt battery in EngineEAR®control unit and attach headphone plug.
2) Turn On/Off switch to “Off” position before putting on headphones. Place headphones
firmly over ears, then turn the switch to “On”. Slowly increase volume to desired setting.
3) Place sensing tip flush on housing surface of suspect problem parts. By keeping the
sensing tip flush against the suspect part, outside noises are blocked. Use the metal
probe when working on hot or difficult to reach areas.
4) Use EngineEAR®to detect bad bearings and bushings, exhaust leaks, bad plug wires,
wind and water leaks, noisy valves and lifters or a squeak or rattle under the dash.
NOTE:
This device electronically amplifies sound and will provide clear sound around
most automobile parts. Static interference will occasionally occur around the coil
and distributor of most cars.
SPECIFICATIONS
65001
PART NO. DESCRIPTION
OPERATING INFORMATION
ADVANCED ELECTRONIC STETHOSCOPE
EngineEAR® EngineEAR®
Rev: 05/03/11
FRONT BACK BACK
COLOR SPECIFICATION:
1-COLOR
MATERIAL SPECIFICATION:
80 lb. Gloss Text
SIZE SPECIFICATION:
5.50"H x 8.50" W - FRONT AND BACK
Black =
100% Black
65001 - EngineEAR™ - STEELMAN
INSTRUCTION CARD
QTYDescription
KIT CONTENTS
Control Unit
Headphones
Rubber Sensor Tip
Metal Probe
1
1
1
1
411
HD-6060N
65012
413
Part No.
CAUTION:
It is against many state laws to operate
a motor vehicle while wearing headphones.
How to Use: