STIEBEL ELTRON HTE 4 Instruction Manual

Bedienung und installation
operation and installation
utilisation et installation
Bediening en installatie
operaÇÃo e instalaÇÃo
oBsługa i instalacja
oBsluHa a instalace
KeZelÉs És telepÍtÉs
Эксплуатация и монтаж
HändetrocKner | Hand dryer | sècHe-mains | Handendroger | secador de mÃos |
susZarKa do rąK | suŠiČ ruKou | KÉZsZÁrÍtÓ | ЭлЕктРиЧЕскиЕ суШилки Для Рук
» HTE 4
» HTE 5

WWW.STIEBEL.CO.NZ HTE 4-5 | 11
ENGLISH
CONTENTS | SPECIAL INFORMATION
SPECIAL INFORMATION
- The appliance may be used by children aged
8 and up and persons with reduced physical,
sensory or mental capabilities or a lack of
experience provided that they are supervised
or they have been instructed on how to use
the appliance safely and have understood the
resulting risks. Children must never play with
the appliance. Children must never clean the
appliance or perform user maintenance unless
they are supervised.
SPECIAL INFORMATION________________________________ 11
OPERATION ____________________________________________ 12
1. General information������������������������������������������ 12
1.1 Document information ������������������������������������������� 12
1.2 Key to symbols ����������������������������������������������������� 12
2. Safety ���������������������������������������������������������� 12
2.1 Intended use�������������������������������������������������������� 12
2.2 Safety information ������������������������������������������������ 12
2.3 CE designation ����������������������������������������������������� 13
2.4 Test symbols�������������������������������������������������������� 13
3. Equipment description ��������������������������������������� 13
4. Operation ����������������������������������������������������� 13
5. Cleaning, care and maintenance���������������������������� 13
6. What to do if ... ����������������������������������������������� 13
6.1 ... the appliance does not start ��������������������������������� 13
6.2 ... the fan is running but there is no hot air������������������ 13
6.3 The type plate ������������������������������������������������������ 13
INSTALLATION _________________________________________ 14
7. Safety ���������������������������������������������������������� 14
7.1 General safety instructions�������������������������������������� 14
7.2 Instructions, standards and regulations���������������������� 14
8. Installation ���������������������������������������������������� 14
8.1 Installation information ������������������������������������������ 14
8.2 Installation conditions and preparations ��������������������� 14
8.3 Power supply������������������������������������������������������� 14
9. Installation ���������������������������������������������������� 14
9.1 Removing the HTE 4 casing cover������������������������������ 14
9.2 Removing the HTE 5 casing cover������������������������������ 14
9.3 Wall mounting ����������������������������������������������������� 15
9.4 Fitting the HTE 4 casing cover ���������������������������������� 15
9.5 Fitting the HTE 5 casing cover ���������������������������������� 15
10. Appliance handover ������������������������������������������ 15
11. Specification��������������������������������������������������� 16
11.1 Specification�������������������������������������������������������� 16
11.2 Wiring diagram ���������������������������������������������������� 16
11.3 Clearances ���������������������������������������������������������� 16
11.4 Guidelines for installation height ������������������������������16
11.5 Dimensions ��������������������������������������������������������� 17
CUSTOMER SERVICE AND WARRANTY _______________ 18
ENVIRONMENT AND RECYCLING______________________ 18

OPERATION
GENERAL INFORMATION
12 | HTE 4-5 Www.STIEbEl.CO.NZ
1. General information
1.1 Document information
The chapter Operation is intended for users and contractors.
The chapter Installation is intended for heating contractors.
Please read Read these instructions carefully before using the
appliance and retain them for future reference. Pass
on the instructions, if required, to a new user.
1.2 Key to symbols
Symbols in this documentation:
In these instructions you will come across symbols and highlights.
These have the following meaning:
Risk of injury! Information concerning possible risk of injury.
Danger of electrocution!
Risk of burning!
Fire hazard!
Never cover!
!Possible damage
Information concerning damage to the appliance,
environmental damage or material losses.
Note! Text next to this symbol is particularly important.
» The "»" symbol indicates that you should do something. The
action you need to take is described step by step.
2. Safety
2.1 Intended use
The appliance is used to dry wet hands.
This appliance is designed for domestic use. It can be used safely
by untrained persons. The appliance can also be used in a non-
domestic environment, e.g. in a small business, as long as it is
used in the same way.
Any other use beyond that described shall be deemed inappropriate.
Observation of these instructions is also part of the correct use of
this appliance. Any modifications or conversions to the appliance
void all warranty rights.
2.2 Safety information
Risk of burning! During operation, temperatures in excess of 90 °C
occur at the hot air outlet.
!WARNING Injury
The appliance may be used by children aged 8 and up
and persons with reduced physical, sensory or mental
capabilities or a lack of experience provided that they
are supervised or they have been instructed on how
to use the appliance safely and have understood the
resulting risks. Children must never play with the
appliance. Children must never clean the appliance or
perform user maintenance unless they are supervised.
Fire hazard! Never place any objects on top of the appliance.
Never lean any objects against it or place any objects
between the appliance and the wall.
Never place any flammable, combustible or
insulating objects or materials, such as laundry,
blankets, magazines, containers with floor polish or
napsan, spray cans or similar, in direct proximity of
the appliance.
Fire hazard! Never operate this appliance ...
... in rooms where the appliance is at risk from fire
or explosion as a result of chemicals, dust, gases
or vapours.
... in the direct proximity of pipes or receptacles that
carry or contain flammable or explosive materials.
... if work such as laying cables, grinding or sealing is
carried out in the installation room.
... if sprays, floor polish or similar products containing
napsan are used. Ensure the room is adequately
ventilated before using the appliance.

OPERATION
EQUIPMENT DESCRIPTION
WWW.STIEBEL.CO.NZ HTE 4-5 | 13
ENGLISH
Danger of electrocution! Never insert any objects into any aperture in the
appliance. This can lead to fatal electric shocks
and/or fires.
Never cover! Never cover the appliance to prevent overheating.
Note! Never operate the appliance if the minimum clearances
to adjacent surfaces are not maintained.
 Note! If you use the appliance in workshops or other rooms
where flue gases, oil and petrol vapours, etc. are
present, or solvents and chemicals are used, lasting,
unpleasant odours and possibly contamination
can result.
 Note! Ensure that the air inlet aperture at the bottom and
back of the appliance is always open.
Note! Maintain the minimum clearance (see chapter
Specification) to the air outlet grille at the bottom.
The hot air must be able to escape unimpeded.
 Note! Never spray the appliance with a water hose to clean
it (see chapter Cleaning, care and maintenance).
2.3 CE designation
The CE designation shows that the appliance meets all essential
requirements according to the:
— Electromagnetic Compatibility Directive
— Low Voltage Directive
2.4 Test symbols
See type plate.
3. Equipment description
The appliance works without contact. It is fitted with an optical
proximity sensor, which automatically activates the heater and
fan when your hands approach the appliance. The response
area is between 4 cm and 13 cm beneath the air outlet grille.
When you remove your hands, the appliance stops after approx.
three seconds.
The casing design makes it virtually impossible to use the appliance
as a depository for cigarettes or similar. Avoid any wall offset at
the top of the appliance to maintain this effect.
The HTE 5 is also protected against damage by its robust diecast
aluminium casing.
4. Operation
» Shake your wet hands over the sink before drying. This reduces
the drying time and saves energy.
» Then hold your hands under the air outlet grille and rub them
together in the hot air current.
5. Cleaning, care and maintenance
A damp cloth is sufficient for cleaning the casing. Never use
abrasive or corrosive cleaning agents. Go over the casing with a
soft cloth. Never spray the appliance using a water hose or other
tools. This would let water penetrate the appliance.
6. What to do if ...
6.1 ... the appliance does not start
— Check the fuses/MCBs in your fuse box.
— Covering the optical proximity sensor impairs the function of
the appliance. In this case, the appliance stops after approx.
three seconds to avoid constant operation. In the event of a
fault, check whether the sensor surface is clear. Once you have
removed any objects, the appliance will work correctly again.
6.2 ... the fan is running but there is no hot air
— When overheating occurs, the heater bank is switched
off but the fan continues to run for cooling purposes. The
temperature sensor switches the heater on again approx.
two minutes after the appliance stops.
6.3 The type plate
The type plate is located at the bottom of the appliance.

14 | HTE 4-5 WWW.STIEBEL.CO.NZ
INSTALLATION
SAFETY
7. Safety
Only qualified contractors should carry out installation,
commissioning, maintenance and repair of the appliance.
7.1 General safety instructions
We guarantee trouble-free operation and operational reliability
only if the original accessories and spare parts intended for the
appliance are used.
7.2 Instructions, standards and regulations
Note! Observe all applicable national and regional
regulations and instructions.
Note! When installing the appliance in rooms with a bath
and/or shower, take the relevant safety zone into
account. Install the appliance in accordance with the
information on the type plate. Refer to VDE0100-701
for the standard applicable to safety zones in Germany.
8. Installation
8.1 Installation information
— Fit the appliance flat against a solid wall (without any offset)
to prevent damage caused by vandalism.
8.2 Installation conditions and preparations
— Always fit the appliance to a vertical wall that is temperature-
resistant to over 90 °C.
— Always maintain the specified minimum clearances.
8.3 Power supply
Note! Observe the type plate. The specified voltage must
match the mains voltage.
Danger of electrocution! Only use a permanent connection to the power supply.
The appliance must be able to be separated from the
mains power supply by an isolator that disconnects all
poles with at least 3 mm contact separation.
» Select a power cable with an adequate cross-section.
» Connect the power cable in accordance with the wiring diagram
(see Specification).
26�07�32�0030
1
1 Plastic bracket
The plastic bracket fixed to the inside of the HTE 5 casing cover
provides additional insulation for the power cable and terminal.
9. Installation
Danger of electrocution! Carry out all electrical connection and installation
work in accordance with relevant regulations.
9.1 Removing the HTE 4 casing cover
26�07�32�0023
3
2
1
1 Casing cover
2 Locking slide
3 Screws
» Undo the screws on the casing cover and locking slide.
» Pull the locking slide down.
» Remove the casing cover.
9.2 Removing the HTE 5 casing cover
» Undo the locking screw.
» Pull the locking slide down.
» Remove the casing cover.
26�07�32�0024
2
1
3
1 Casing cover
2 Locking slide
3 Locking screw

WWW.STIEBEL.CO.NZ HTE 4-5 | 15
ENGLISH
INSTALLATION
APPLIANCE HANDOVER
9.3 Wall mounting
lone für M ont a
26�07�32�0025
» Cut out the drilling template. This can be found at the end of
these instructions.
» Transfer the four mounting points on to the wall using the drilling
template. Pay attention to the length and position of the power
cable. Use our height guidelines to help you (see Specification).
» Drill the fixing holes and insert rawl plugs.
» Insert the lower fixing screws into the wall.
26�07�32�002626�07�32�0039
1
1 Cable entry
» Pull the power cable through the cable entry in the back panel
of the appliance.
» Fit the appliance with the keyhole fixings on to the fixing screws.
» Secure the appliance to the wall using two more screws.
» Connect the power cable to the appliance.
Note! Ensure that the wires of the power cable are not near
the fan motor.
Note! Observe the maximum length of the power cable.
(See Specification)
9.4 Fitting the HTE 4 casing cover
26�07�32�0028
» Place the casing cover on the appliance so that it is slightly tilted
and pivot it towards the wall.
» Push the locking slide up as far as it will go.
» Secure the locking slide and the casing cover with screws.
9.5 Fitting the HTE 5 casing cover
26�07�32�0029
» Slide the casing cover, slightly tilted, over the appliance towards
the wall as far as it will go. Ensure that the hooks provided on
the bottom of the casing cover catch behind the back panel of
the appliance.
» To lock in place, lift the casing cover slightly at the front and
push the locking slide up as far as it will go.
» Secure the locking slide with screws.
10. Appliance handover
Explain the functions of the appliance to the user. Draw special
attention to the safety information. Hand the operating and
installation instructions to the user.

16 | HTE 4-5 WWW.STIEBEL.CO.NZ
INSTALLATION
SPECIFICATION
11. Specification
11.1 Specification
Model Hand dryer
Type HTE 4 HTE 5
Part number 073007 073008
Colour white signal white
Casing Plastic (ABS) Diecast aluminium,
painted
Operating details
Rated output W1800 1800
Output W1740 1740
Fan power W60 60
Connection 1/N 220-240 V 50 Hz 1/N 220-240 V 50 Hz
Protection cat. to EN 60335 II II
Protection IP 23 IP 23
Operating noise ~ dB (A) 54 54
Air throughput ~ m³/h 146 146
Runtime ~ s 36 36
Dimensions and weights
Dimensions H x W x D mm 250 x 238 x 230 266 x 257 x 230
Weight kg 2.5 4
Maximum length of the
power cable
mm 200 200
11.2 Wiring diagram
26�07�32�0039
11.3 Clearances
40
130
≥ 300
≥ 127
26�07�32�0032
1 1
1 Detection range of IR proximity sensor
11.4 Guidelines for installation height
Note!
Height (mm) indicates the clearance between the
bottom of the appliance and the floor.
Age Age Height (mm)
Adult man 1350
Adult woman 1250
Nursery school age 4 - 7 810
Primary school age 7 - 10 910
Middle school age 10 - 13 1120
High school age 13 - 16 1250

WWW.STIEBEL.CO.NZ HTE 4-5 | 17
ENGLISH
INSTALLATION
SPECIFICATION
11.5 Dimensions
11.5.1 HTE 4
b01
238
249
184230
192
15
95
30 161
3
D0000025609
11.5.2 HTE 5
b01
3
257
266
233
95
15
192
160
184
35
D0000025610

InternatIonal
Guarantee | envIronment and recyclInG
Warranty
The warranty conditions of our German companies do not
apply to appliances acquired outside of Germany. In countries
where our subsidiaries sell our products, it is increasingly the
case that warranties can only be issued by those subsidiaries.
Such warranties are only granted if the subsidiary has issued
its own terms of warranty. No other warranty will be granted.
We shall not provide any warranty for appliances acquired in
countries where we have no subsidiary to sell our products.
This will not aect warranties issued by any importers.
Environment and recycling
We would ask you to help protect the environment. After use,
dispose of the various materials in accordance with national
regulations.
CUSTOMER SERVICE
AND WARRANTY ENVIRONMENT AND RECYCLING
18 | HTE 4-5 WWW.STIEBEL.CO.NZ