STIEBEL ELTRON SH 10 SL User manual

275987
GESCHLOSSENER (DRUCKFESTER) WARMWASSERSPEICHER | CLOSED (PRESSURIZED) WATER
STORAGE HEATER | BALLON D’EAU CHAUDE FERMÉ (À ÉCOULEMENT LIBRE) | GESLOTEN
(DRUKBESTENDIGE) WARMWATERBOILER |32-(012¤&,2:(&,¤1,(1,2:(2*5=(:$&=(WODY |7/$.29v=d62%1.29v2+¢9$o(92'<| ZÁRT (NYOMÁSOS) MELEGVÍZTÁROLÓ |
ȼɈȾɈɇȺȽɊȿȼȺɌȿɅɖɗɅȿɄɌɊɂɑȿɋɄɂɃɇȺɄɈɉɂɌȿɅɖɇɕɃɇȺɉɈɊɇɕɃ» SH 10 SL | SH 10 SLi comfort
» SH 15 SL | SH 15 SLi comfort
GEBRAUCHS- UND MONTAGEANLEITUNG
OPERATING AND INSTALLATION INSTRUCTIONS
NOTICE D’UTILISATION ET DE MONTAGE
GEBRUIKS- EN MONTAGEAANWIJZING
,16758.&-$2%68*,,0217$¾81d92'.328½,7$.0217d½,KEZELÉSI ÉS SZERELÉSI UTASÍTÁS
ɂɇɋɌɊɍɄɐɂəɉɈɆɈɇɌȺɀɍɂɗɄɋɉɅɍȺɌȺɐɂɂ




2
Deutsch Seite 4-8
Inhaltsverzeichnis
English page 10-13
List of contents
Français page 14-17
Sommaire
Nederlands bladzijde 18-21
Inhoudsopgave
Polski strona 22-25
Spis treści
Česky strana 26-29
Obsah
Magyar oldal 30-33
Tartalomjegyzék
rÂÚÚµÒÓsÛÙËÖÒÞËè&RÎÏÙÐËÖÒÏ1. Gebrauchsanleitung _________________________4
1.1 Gerätebeschreibung_____________________ 4
1.2 Das Wichtigste in Kürze ________________ 4
1.3 Bedienung ________________________________ 4
1.10 Wichtige Hinweise _______________________ 4
1.5 Pflege und Wartung _____________________ 4
1.6 Was tun wenn . . . ? _____________________ 4
1.7 Sonderzubehör ___________________________ 4
2. Montageanleitung ___________________________5
2.1 Geräteaufbau ____________________________ 5
2.2 Gerätebeschreibung_____________________ 5
2.3 Technische Daten ________________________ 5
2.4 Vorschriften und Bestimmungen _____ 5
2.5 Wichtige Hinweise _______________________ 5
2.6 Montageort ______________________________ 5
2.7 Gerätemontage _________________________ 5
2.8 Erstinbetriebnahme _____________________ 5
2.9 Servicehinweise __________________________ 5
3. Störungsbeseitigung ________________________7
4. Umwelt und Recycling_______________________7
5. Kundendienst und Garantie ________________8
1. Operating Instructions ____________________ 10
1.1 Description of Unit ______________________ 10
1.2 The most important points in brief __ 10
1.3 Operation _________________________________ 10
1.4 Important Note __________________________ 10
1.5 Care and Maintenance _________________ 10
1.6 What to do if.... __________________________ 10
1.7 Sonderzubehör __________________________ 10
2. Installation Instructions ___________________ 11
2.1 Unit Type _________________________________ 11
2.2 Description of Unit ______________________ 11
2.3 Technical Data ___________________________ 11
2.4 Regulations and Conditions___________ 11
2.5 Important Notes_________________________ 11
2.6 Installation Site _________________________ 11
2.7 Unit Installation ________________________ 11
2.8 Initial Use ________________________________ 11
2.9 Service Notes ____________________________ 11
3. Defect Rectification ________________________ 13
4. Environment and recycling ________________ 13
5. Guarantee___________________________________ 13
1. Instructions d’utilisation à l‘usage _______ 14
1.1 Description de l’appareil ______________ 14
1.2 Sommaire des informations essenti-
elles _______________________________________ 14
1.3 Utilisation ________________________________ 14
1.4 Observations importantes _____________ 14
1.5 Entretien et maintenance _____________ 14
1.6 Que faire si … ?__________________________ 14
1.7 Accessoires spécifiques ________________ 14
2. Instructions de montage __________________ 15
2.1 Composants de l’appareil ____________ 15
2.2 Description de l’appareil ______________ 15
2.3 Caractéristiques techniques __________ 15
2.4 Normes et réglementations __________ 15
2.5 Remarque importante _________________ 15
2.6 Lieu de montage _______________________ 15
2.7 Montage de l’appareil ________________ 15
2.8 Première mise en service _____________ 15
2.9 Instructions de maintenance__________ 15
3. Dépannage _________________________________ 17
4. Environment et recyclage__________________ 17
5. Garantie_____________________________________ 17
1. Gebruiksaanwijzing _______________________ 18
1.1 Beschrijving van het toestel___________ 18
1.2 In kort bestek ____________________________ 18
1.3 Bediening ________________________________ 18
1.4 Belangrijke instructies _________________ 18
1.5 Reiniging en onderhoud ______________ 18
1.6 Wat te doen, indien . . . ? _____________ 18
1.7 Speciale accessoires ____________________ 18
2. Montageaanwijzing _______________________ 19
2.1 Opbouw van het toestel _______________ 19
2.2 Beschrijving van het toestel___________ 19
2.3 Technische gegevens ___________________ 19
2.4 Voorschriften en bepalingen__________ 19
2.5 Belangrijke instructies _________________ 19
2.6 Plaats van montage ____________________ 19
2.7 Montage van het toestel ______________ 19
2.8 Eerste inbedrijfsname _________________ 19
2.9 Service-instructies ______________________ 19
3. Verhelpen van storingen __________________ 21
4. Millieu en recycling ________________________ 21
5. Garantie_____________________________________ 21
1. Instrukcja obsługi __________________________ 22
1.1 Opis urządzenia _________________________ 22
1.2 Ważne wskazówki w skrócie __________ 22
1.3 Obsługa ___________________________________ 22
1.4 Ważna wskazówka______________________ 22
1.5 Konserwacja i czyszczenie_____________ 22
1.6 Co robić, gdy ...? ________________________ 22
1.7 Osprzęt dodatkowy _____________________ 22
2. Instrukcja montażu ________________________ 23
2.1 Budowa urządzenia ___________________ 23
2.2 Opis urządzenia _________________________ 23
2.3 Dane techniczne_________________________ 23
2.4 Przepisy i zalecenia _____________________ 23
2.5 Ważne wskazówki_______________________ 23
2.6 Miejsce montażu urządzenia _________ 23
2.7 Montaż urządzenia _____________________ 23
2.8 Pierwsze uruchomienie ______________ 23
2.9 Wskazówki serwisowe _________________ 24
3. Usuwanie usterek _________________________ 25
4. Środowisko naturalne i recykling_________ 25
5. Gwarancja __________________________________ 25
1. Návod k použití ____________________________ 26
1.1 Popis přístroje ___________________________ 26
1.2 Nejdůležitější informace ve zkratce__ 26
1.3 Obsluha ___________________________________ 26
1.4 Důležité pokyny__________________________ 26
1.5 Ošetřování a údržba ____________________ 26
1.6 Co dělat, když . . .? _____________________26
1.7 Zvláštní příslušenství ___________________ 26
2. Instrukce k montáži ________________________ 27
2.1 Konstrukce přístroje ____________________ 27
2.2 Popis přístroje __________________________ 27
2.3 Technická data __________________________ 27
2.4 Předpisy a ustanovení _________________ 27
2.5 Důležité pokyny _________________________ 27
2.6 Montážní místo _________________________ 27
2.7 Montáž přístroje ________________________ 27
2.8 První uvedení do provozu ____________ 27
2.9 Pokyny pro servis _______________________ 27
3. Odstraňování závad _______________________ 29
4. Ekologie a recyklace _______________________ 29
5. Záruční podmínky__________________________ 29
1. Kezelési utasítás ___________________________ 30
1.1 Készülék leírása _________________________ 30
1.2 A legfontosabbak röviden _____________ 30
1.3 Kezelés ____________________________________ 30
1.4 Fontos utasítások _______________________ 30
1.5 Tisztítás és karbantartás _______________ 30
1.6 Mit tegyenek, ha… ______________________ 30
1.7 Zvláštní příslušenství ___________________ 30
2. Szerelési utasítás __________________________ 31
2.1 A készülék felépítése __________________ 31
2.2 A készülék leírása_______________________ 31
2.3 Műszaki adatok__________________________ 31
2.4 Előírások és meghatározások_________ 31
2.5 Fontos figyelmeztetések _______________ 31
2.6 A felszerelés helye ____________________ 31
2.7 A készülék felszerelés _________________ 31
2.8 Első üzembe helyezés _________________ 31
2.9 Szervízelőírások _________________________ 31
3. Hibaelhárítás _______________________________ 33
4. Környezet és újrahasznosítás _____________ 33
5. Garancia_____________________________________ 33
ɂɧɫɬɪɭɤɰɢɹɩɨɷɤɫɩɥɭɚɬɚɰɢɢ_____ 34
Ɉɩɢɫɚɧɢɟɩɪɢɛɨɪɚ___________ 34
Ʉɨɪɨɬɤɨɨɫɚɦɨɦɜɚɠɧɨɦ______ 34
ɍɩɪɚɜɥɟɧɢɟ_________________ 34
ȼɚɠɧɵɟɭɤɚɡɚɧɢɹ____________ 34
ɍɯɨɞɢɬɟɯɧɢɱɟɫɤɨɟɨɛɫɥɭɠɢɜɚɧɢɟ34
ɑɬɨɞɟɥɚɬɶɟɫɥɢ«"__________ 34
ɋɩɟɰɢɚɥɶɧɵɟɩɪɢɧɚɞɥɟɠɧɨɫɬɢ_____________ 34
2.ɂɧɫɬɪɭɤɰɢɹɩɨɦɨɧɬɚɠɭ_________ 35
Ʉɨɧɫɬɪɭɤɰɢɹɩɪɢɛɨɪɚ_________ 35
Ɉɩɢɫɚɧɢɟɩɪɢɛɨɪɚ___________ 35
Ɍɟɯɧɢɱɟɫɤɢɟɯɚɪɚɤɬɟɪɢɫɬɢɤɢ___ 35
ɉɪɟɞɩɢɫɚɧɢɹɢɨɩɪɟɞɟɥɟɧɢɹ___ 35
ȼɚɠɧɵɟɭɤɚɡɚɧɢɹ____________ 35
Ɇɟɫɬɨɦɨɧɬɚɠɚ______________ 35
Ɇɨɧɬɚɠɩɪɢɛɨɪɚ_____________ 35
ɉɟɪɜɵɣɜɜɨɞɜɷɫɤɩɥɭɚɬɚɰɢɸ___ 35
ɍɤɚɡɚɧɢɹɩɨɫɟɪɜɢɫɧɨɦɭɨɛɫɥɭɠɢɜɚɧɢɸ_______________ 36
ɍɫɬɪɚɧɟɧɢɟɧɟɢɫɩɪɚɜɧɨɫɬɟɣ______ 37
Ɉɤɪɭɠɚɸɳɚɹɫɪɟɞɚɢɜɬɨɪɫɵɪɶɺ_____________________ 37
Ƚɚɪɚɧɬɢɹ_______________________ 37

3
B
A
FG
E
D
CI. II.
26_02_06_0008
C4856.01
Typ SH 10 SL
SH 10 SLi
SH 15 SL
SH 15 SLi
a275 mm 295 mm
b295 mm 316 mm
d200 mm 200 mm
e387 mm 495 mm
h503 mm 601 mm
i116 mm 106 mm
L 1
L 2
L 1 L 2
SH 10 SL | SH 10 SLi 160 mm 250 mm
SH 15 SL | SH 15 SLi - 2,0 kW 200 mm 310 mm
SH 15 SL | SH 15 SLi - 3,3 kW 200 mm 320 mm
C4857.01








3
4
C26_02_06_0110
2
1
5
6
7
8
26_02_06_0111





26_02_06_0116
26_02_06_0117




















d
a
b
c
5

10
1. Operating Instructions for the user and engineer
1.1 Description of Unit
• The closed (pressurized) water storage he-
ater keeps the water content permanently
ready at the pre-selected temperature.
• Only tap fittings in conjunction with the
KV 307 or KV 40 safety group may be used.
1.2 The most important points
in brief
• Set the desired hot water temperature
using the temperature selector (1)
• An illuminated display (2) indicates that
the unit is heating up.





1
2
C26_02_06_0095
1.3 Operation
Temperature setting
°C = cold. At this setting the unit, but not
the fitting or water pipe, is protected
from frost
Eco = At this setting the unit is protected
from frost, although this does not
protect the fitting or the water pipe.
82 = max. temperature setting.
Note:
On request, the engineer can set a tempera-
ture limit on the unit (see .8 “First Use”) so
that the temperature is fully adjustable up to
this limit.
Heat up time:
If the entire water content is used, the heat up
time is as indicated in the graph.
35 °C 55 °C E 65 °C 82 °C
[min] SH 15 SL
SH 15 SLi
2 kW
SH 10 SL
SH 10 SLi
2 kW
3,3 kW
SH 15 SL
SH 15 SLi
40
35
30
25
20
15
10
5
0
Example SH 10 SL | SH 10 SLi:
Temperature setting: 65 °C
Heat up time: approx. 18 minutes
Mixing water quantity:
Using the temperature, you set a mixed water
quantity for e.g. 40 °C.
[ l ]
SH 15 SL
SH 15 SLi
SH 10 SL
SH 10 SLi
45
40
35
30
25
20
15
10
5
0
40 °C 55 °C E 65 °C 82 °C
Example SH 10 SL | SH 10 SLi:
Temperature setting: 65 °C
Cold water feed: 15 °C
Mixed water quantity: approx. 20 l
1.4 Important Note
•The water storage heater is under
mains water pressure.
•During heating up, water will drip out of
the safety valve.
If water continues to drip out of the safety
valve after heating up has been completed,
the device must be switched off and depres-
surized, and a qualified installer called.
•The blow-out line of the safety valve must
not be closed.
•With temperature settings over 45 °C, wa-
ter at a high temperature may start flowing
immediately.
• If it is intended that children or people
with restricted physical, sensory or mental
capabilities are to operate the appliance,
they must only be permitted to do so after
appropriate instruction has been provided by
the person responsible for their safety.
Children should be supervised to ensure that
they do not play with the device.
Risk of scalding!
To avoid risk of accidental resetting of the
protective temperature restrictor in the event
of a fault, the unit must not be connected via
a timer switch.
Limescale can block the outlet and cause pres-
sure to build up in the heater.
Signs of limescale are boiling sounds and re-
duced water flow. In such a case, the unit and
fitting must be descaled by an engineer.
The thermostat knob may only be removed by
an engineer.
All information in these Operating and In-
stallation Instructions must be observed. The
instructions contain important information for
safety, operation and maintenance of the unit.
1.5 Care and Maintenance
To clean the unit, simply wipe with a damp
cloth. Do not use abrasive or aggressive clea-
ning agents.
Maintenance work should only be
performed by an engineer.
1.6 What to do if....
... there is no hot water:
Check the thermostat, plug and fuse.
...there is a boiling sound from the unit:
Have the unit and fitting descaled by an en-
gineer.
... see also 3. „Defect rectification for the user
and engineer”.
If an engineer is called out for a problem, to
help him resolve this problem quickly and effi-
ciently, please give him the information on the
unit rating plate, as shown below (8):

..............
C26_02_06_0054
1.7 Sonderzubehör
Stiebel Eltron Bestell-Nummern:
• safety group
– KV 307 (0.7 MPa) 00 07 57
– KV 40 (0.6 MPa) 00 08 28
• installation kit "Permanent electrical con-
nection"
– installation kit 22 32 19

11
English
2. Installation Instructions for the engineer
Installation and electrical connection may
only be carried out by an engineer in ac-
cordance with these instructions.
2.1 Unit Type A
1Temperature selection knob
2Indicator light
3Cold water connection (blue)
4Hot water connection (red)
5Electrical cable
6Suspension rail
7Electric heating element with protective pipe
for thermostat and temperature limiter
8Rating plate
2.2 Description of Unit
Closed (pressurized) hot water heater for
oversink mounting for supplying one or more
taps, for the heating of cold water in ac-
cordance with EN 806.
Operation is only permissible with tap fittings
in conjunction with the KV 307 or KV 40 safety
group.
2.3 Technical Data
Current data on the rating plate.
Type SH 10 SL
SH 10 SLi
SH 15 SL
SH 15 SLi
SH 15 SL
SH 15 SLi
Nominal ca-
pacity
10 l 15 l 15 l
Type of cons-
truction
closed
Permissible
operating
overpressure
0.7 MPa
Test pressure
(untreated
tank)
1.4 MPa
Weight 7.6 kg 10.5 kg 10.8 kg
Heating ca-
pacity
2 kW 2 kW 3,3 kW
Voltage 230 V
Flow rate, max. 10 l/min 12 l/min
Protection to
EN 60529
IP 24 D
Electrical ca-
ble approx.
650 mm with plug
Temperature
setting range
approx. 35 °C - 82 °C
(fully adjustable)
- Fixed connection:
If the appliance is instended to be con-
nected to the AC mains (appliance connec-
tion socket), it must be capable of all-pole
disconnection from the mains by means of
a circuit sever of at least 3 mm.
SH 10 SL | SH 10 SLi:
Installation with a direct (fixed) electrical
cable is not permitted.
SH 15 SL and SH 15 SLi:
Installation with a fixed connection cable
is only permitted in conjunction with the
installation kit "Permanent electrical con-
nection" (Stiebel Eltron order no. 22 32 19).
Only with this installation kit is protection
class IP 24 D retained.
• The conditions of the local electricity sup-
ply company and competent water supply
authority must be observed.
2.5 Important Notes
If the water connections on the unit
are transposed, the unit will not func-
tion and the components may be damaged.
• The operating over-pressure of 0.7 MPa
must not be exceeded.
• Install the KV 307 Hsafety group in the
cold water connection, up to max. 0.56 MPa
at the appliance connection.
The KV 40 Isafety group (with pressure
reducer) can be set up to 1 MPa; setting of
max. 0.48 MPa at the appliance connection.
The blow-out line of the safety group must
be laid with a fall gradient.
Regular maintenance and actuation of the
safety device is required (see Instruction
leaflet for the safety group).
2.6 Installation Site B
The storage tank must be installed in a frost-
free place, upright, with the water connections
at the bottom, close to the tap from which hot
water will most frequently be drawn.
2.7 Unit Installation B
• Fit the hanging bracket, determining the
position with the aid of the mounting
template provided. Select fixing materials
according to the strength of the wall.
Surplus cable can be stored in the cable
holder provided.
• Suspend the unit.
• Fit water connections with surface sealing.
Connections to the heater:
right blue = cold water connection (3)
left red = hot water connection (4).
• Set the flow volume at the valve of the
KV 307 / KV 40 safety group at max.
10 l/min. for the SH 10 SL(i), and 12 l/min.
with the SH 15 SL(i).
• Provide the hot water pipe with thermal
insulation (concealed).
• Pipe material:
Cold water pipe Hot water pipe
Copper pipe Copper pipe
Steel pipe Copper pipe
Note regarding plastic pipe systems:
Operating temperatures of up to max. 82 °C
can be set for the heaters. The maximum
temperature can be set to 65 °C.
In the event of a fault, temperatures of up
to 105 °C may occur. The plastic pipe system
used must be designed for these conditions.
2.8 Initial Use C
(May only be performed by the engineer!)
I. Open the hot water tap or set the one-
hand mixer tap to “warm” until the wa-
ter runs freely with no air bubbles.
II. Check the safety valve. During bleeding,
a full jet of water must run out.
III. Connect the electrical plug and select the
temperature.
Risk of running dry!
If the sequence is confused, the tem-
perature limiter will actuate. In such a case,
the thermostat must be replaced and the
limiter must be made ready for operation
again by pressing the reset button.
IV. Temperature setting restrictor F:
Only if the restricted temperature setting
is required is the max. temperature set
via the restrictor ring. To do this, pull off
the thermostat knob and restrictor ring.
Set the restrictor ring to the desired max.
setting and push the thermostat knob
back on.
V. Remove protective film from controls.
Unit hand-over:
Explain to the user how the unit works and
how to operate it. Point out any possible dan-
gers (scalding). Give the user these Installation
and Operating Instructions for safe keeping.
2.9 Service Notes
• Open unit G:
aPull off thermostat and temperature res-
trictor ring. Remove screw.
bLower locking bolt
c Swivel housing cover aside and remove.
dOpen clamp band (protection against tilt-
ing).
• Replace electrical cable:
To replace the connecting cable, use Stiebel
Eltron.
2 kW: Order no. 02 06 71, or with an
H05VV-F3x1.0 cable
3.3 kW: Order no. 02 39 71, or use an
H05VV-F3x1.5 cable. Lay the connecting line in
the channel G(5)!
Circuit diagram D
• Positioning the thermostat/temperature
limiter sensor in the protection pipe:
When replacing or dismantling the tempe-
rature regulator/limiter, the sensors must be
introduced into the protection pipe.
• Drain unit:
The unit is drained via the connector.
Table 1
2.4 Regulations and Conditions
• Perfect function and operating safety
can only be guaranteed with the original
Stiebel Eltron accessories and spare parts
designed for the unit.
• The fitting outlet serves for ventilation. Do
not block the outlet connector or fitting
swivel arm. Do not use a perlator or hose
with jet regulator.
•Electrical connection
- Plug connection:
An earthed socket is required. This must be
freely accessible after the device has been
installed. If country-specific plugs and sockets
are used, they must be fitted with an earthing
contact and must conform to the individual
national standards.

12
• Descaling:
Remove heating flange, remove coarse scale
by careful tapping, immerse heating element
in limescale remover up to the flange plate.
• Checking earth conductor in accordance:
Disconnect the plug and remove the thermos-
tat. Test at the thermostat fixing screw and
earth contact of the connection cable.
H
I
C26_02_06_0112




1 2 3 4 5
6 KV 40
1 2 3 4
6 KV 307
1
2
6
3 / 4
5
7
1
2
6
3 / 4
7
1Safety valve
2Non-return valve
3Check valve
4Throttle
6Connection point for manometer
7Funnel with odour trap
C26_02_06_0113
C26_02_06_0114C26_02_06_0115
1Safety valve
2Non-return valve
3Check valve
4Throttle
5Pressure reducing valve
6Connection point for manometer
7Funnel with odour trap

13
3. Defect Rectification for the user and engineer
Defect Cause Solution
No hot water despite hot water
tap being fully open.
No power. User / Engineer: Check fuses on domestic system.
Limescale on jet regulator. User / Engineer: Clean or replace jet regulator on fitting.
Temperature limiter (STB) has
actuated.
Engineer: Rectify the cause of the fault (replace thermostat)
and make the limiter ready for operation again by
pressing the reset button.
Boiling sound in heater. Limescale in heater. Engineer: Descale unit.
Table 2
5. Guarantee
For guarantees please refer to the pespective
terms and conditions of supply for your coun-
try.
4. Environment and recycling
The installation, electrical connection
and initial operation of this appliance
should be carried out by a qualified installer.
$$$ "'+(('  !)'("#('$#'#+(("& &)'-!)'(# ('$&( -"'$#'##&"(# # &) (#"'
The company does not accept liabi-
lity for failure of any goods supplied
which accor-dance with the manufacturer‘s
instructions.
English