Stiga Play The Best T8135 User manual

1. Read this manual carefully before starting assembly. Read each step completely before beginning
each step.
2. Some smaller parts may be shipped inside larger parts. Check inside all parts and cartons
before assembling or ordering parts.
3. To make assembly easier, use the Hardware Identifier on page 9 to identify and sort all
fasteners. Check all cartons for kits. All hardware may not be located in one kit.
4. Do not tighten hardware until instructed to do so. If hardware is tightened too soon, mounting holes
may not align and parts may not easily fit together. Leave locknuts slightly loose until you are instructed to
tighten them.
5. Tools required for assembly: Phillips Screwdriver, Two 7/16 Wrenches, One 3/8 Wrench (an adjustable
wrench may be substituted for the wrenches).
OWNER'S MANUAL
MODEL NOS.
T8135,T8135,
T8135,T8135,
T8135, COMPETITION
T8165,T8165,
T8165,T8165,
T8165, AVENGER
T8157,T8157,
T8157,T8157,
T8157, ACCLAIM
TABLE TENNIS TABLE
Please Do Not Return This Product To The Store!
Contact Escalade®Sports customer service department at:
Phone: [phone] Toll – Free !
Fax: [phone] Toll – Free !
E-mail: [email protected]
Mailing Address (correspondence only):
Escalade Sports
PO Box 889
Evansville, IN 47706
Please visit our World Wide Web site at: www.escaladesports.com
ON-LINE TROUBLE SHOOTING TECHNICAL ASSISTANCE
ON-LINE PARTS REQUESTS FREQUENTLY ASKED QUESTIONS
ADDITIONAL ESCALADE®SPORTS PRODUCT INFORMATION
2L-6795-00
Escalade® Sports products may be manufactured and/or licensed under the following patents.
6120397, 5816957, 5769744, 5119741, 4911085, 4717157, D460140, D420563
Additional patents may be pending. One or more of the listed patents and/or pending patents may cover specific product.

2
1. Lay table top #1 painted side down, on a smooth, flat
surface. Use the shipping container to protect the
painted surface of the table top.
2. Assemble the two “L” tubes and the center tubes that
make up the “U” Support and the “U” Leg. Align on
Table Top as shown in Figure 1. Note: “U” Leg is
larger and wider than the U Support. The U-
leg should be installed on the end of the table
half with the end rail mounting holes.
3. Put plastic caps #13 on the end of U-leg #2.
IMPORTANT:
Be sure the slot in the six U-clips #3 all face the same
direction (toward the end of the table with the U-
support) as shown.
4. Align the holes in the U-clips #3 with pilot holes in table top
assembly and secure with twenty four screws #20 as shown.
IMPORTANT: U-Leg is wider than U-support.
Make sure they are assembled exactly as
shown. If not, there will be a large gap between
table halves and table will not operate properly!
Figure 1
Figure 2

3
8. Rotate U-support #7 until you see the screw hole in
the slot of U-clip # 3. Slide U-support #7 side to side
if necessary.
9. Insert screw #19 through slot in U-clip #3 and into
U-support #7. Thread it all the way into U-support
#7 until it touches the back of the tube. There should
be about 3/8 inch of screw #19 left sticking out. Re-
peat for U Leg #2.
Figure 5
5. Lay out rails #25 and 26, as shown in Figure 3, around edges
of table top.
6. Line up holes in rails with pilot holes in top and secure using
eighteen screws #20. See Figure 3.
Figure 4
Figure 3
7. Lay Corner Caps #22 on table as shown in Figure 4. If Corner
Cap sticks above table top surface of table, flip over so shorter
distance is against edge. Secure to bottom of table with three
screws #21.

4
10. Attach end of linkages #4 with two holes to INSIDE of U-leg
#2 as shown in Figure 6. Secure through end hole with screws
#23, locknuts #15 and plastic spacers #31. Tighten hardware
snug enough to keep table stable but do not overtighten. Tubes
must pivot freely.
11. On one side of the table attach slotted end of safety strap #6 to
INSIDE of U-Leg #2 using one bolt #29, one spacer #30,
one washer #24, and one hex nut #15. Tighten hardware until
snug but do not overtighten. Tubes must pivot freely. See Figure
7.
12. Attach other end of safety strap #6 to OUTSIDE of linkage #4
using one bolt #9, one washer #24, one spacer #30, and one
hex nut #15.
Important! Do NOT put other safety strap #6 on this table half.
It will be installed on other table half later.
13. Attach other end of linkages #4 to OUTSIDE of U-support #7
with screws #14 and plastic washers #24. Then slide name
panel #5 onto the same screws #14 on INSIDE of U-support
#7. Secure with locknuts #15. Tighten hardware until snug but
do not overtighten. Tubes must pivot freely.
14. Attach bottom of name panel #5 to U-supports #7. Secure with
hex bolts #9 and locknuts #15. Tighten nuts but be careful not
to crush tubes. See Figure 6.
Figure 6
Figure 8
15. Gently tap caster sockets #12 into U-support #7 until flange
on sockets touches the edge of the tube. DO NOT HIT CASTER
SOCKET DIRECTLY WITH A HAMMER! SET A PIECE OF
WOOD ON CASTER SOCKET AND HIT PIECE OF
WOOD TO DRIVE CASTER SOCKET INTO U-SUPPORT.
16. Insert casters #11 into caster sockets #12.
17. Prepare an area for the assembly of the second table top half. If
necessary, move the first table top half aside with the aid of a
helper. Be sure to place it in a location where it won't be dis-
turbed or damaged. If setting on its side, be sure to place the
bottom edge no less than 12 inches away form the wall. Also
be sure to place carpet or pieces of the shipping carton down
to protect table top edges. If floor is not carpeted, brace table
top half with a heavy object to keep it from sliding.
AT LEAST TWO ADULTS ARE NEEDED
TO MOVE TABLE HALF!
CAUTION:
Figure 7

5
18. Repeat steps 1 through 12 on second table half.
19. Gently tap caster sockets #12 into U-support #7 on second table
half until flange on sockets touches the edge of the tube. DO NOT
HIT CASTER SOCKETS TOO HARD WITH A HAMMER. Cast-
ers could break if hit too hard.
20. Insert casters #11 into caster sockets #12 on second table half.
21. Attach linkages #4 to the OUTSIDE of U-support #7 on second
table half. Use screws #14, plastic washers #24 and hex nuts #15.
NOTE: Tighten locknuts #15 finger tight only. They will be
removed when the two table top halves are connected.
Figure 9
CAUTION:
AT LEAST TWO ADULTS ARE NEEDED TO
COMPLETE THE REMAINDER OF THE
ASSEMBLY!

6
INSTALL SAFETY LATCHES #8 AS SHOWN ABOVE FOR PROPER USE OF
TABLE! DO NOT SKIP THIS STEP! DO NOT OPERATE TABLE UNTIL SAFETY
LATCHES ARE INSTALLED AND ASSEMBLY IS COMPLETE!
CAUTION:
25. Choose a name panel #5 on either side of the table and install
one safety latch #8 into the right-hand hole on that name panel
as shown in Figures 11 & 12. Use one screw #10 one washer
#17 and one hex nut #16. NOTE: Flange on safety latch
must extend over top of name panel as shown in Figure
11. Safety latch must pivot freely.
26. Go to the other side of the table and install the second safety latch
into the right-hand hole on the other name panel #5. NOTE:
Safety latches must be attached diagonally across
from each other. (See Figure 12)
Figure 12
Figure 11
Figure 10
22. Make sure the legs on the first table top half (the half with the name panel #5) are open. With one person on each side of the table, lift and set
table half on its legs. Place table against a wall as shown above to help stabilize table top half while second half is being attached. Be sure there
is enough room to connect second half.
23. Place a hex bolt #9 and a locknuts #15 on floor next to caster wheels (on both sides of the table half) so they will be handy for the next step.
24. With a person on both sides of the second table half, slide the second table half against the first table half. Remove locknuts #15 from screws
#14 on second table half where U-support #7 and linkages #4 join. Align holes in name panels #5 (on first table half) with holes in U-
supports (on second table half). Secure second table half to top hole in name panel #5 using hex bolt #14 installed earlier and locknuts just
removed. Secure second table half to bottom hole in name panel #5 with the two hex bolts #9 and locknuts #15 you placed on the floor
earlier. Tighten locknuts snug but do not overtighten. These joints must pivot. At this point go back and tighten hex bolts #9.
BE SURE THE FIRST TABLE HALF YOU ASSEMBLED (WITH NAME PANELS #5
ATTACHED) IS STABLE AND AGAINST A WALL. DO NOT LEAVE TABLE HALF
STANDING UNATTENDED.
CAUTION:
UNTIL THE TABLE HALVES ARE CONNECTED THEY WILL NOT STAND ON THEIR
OWN. IT IS RECOMMENDED TO HAVE THREE PEOPLE TO CONNECT TABLE
HALVES. TWO TO STABILIZE TABLE AND ONE TO BOLT TABLE TOGETHER.
CAUTION:

7
TO OPEN:
1. Pull both legs away from table slightly.
2. Stand behind the table near the safety latch.
3. Hold table half with one hand and pivot safety latch enough to
allow the edge of the table half to pass over it.
4. While keeping an eye on the safety latch, pivot table half until it
moves past the safety latch. Once edge of table has passed over
safety latch, stop pivoting table half.
5. With both hands on the table half, center yourself along the table
half and lower the table half to the floor.
6. Repeat for the other table half.
TO CLOSE:
1. Lift table half upward and inward to vertical position.
2. Check to be sure that table half is locked in the safety latch.
3. Repeat for the other table half.
OPENING AND CLOSING INSTRUCTIONS
READ OPERATING INSTRUCTIONS CAREFULLY BEFORE OPERATING TABLE! DO
NOT ALLOW CHILDREN TO OPEN TABLE! DO NOT CLIMB, STAND OR JUMP ON
TABLE! SERIOUS OR FATAL INJURY MAY RESULT! THIS IS NOT A TOY! TABLE IS
TO BE OPENED OR CLOSED BY ADULTS ONLY! FAILURE TO COMPLY WITH
OPENING AND CLOSING INSTRUCTIONS COULD RESULT IN PERSONAL INJURY
OR PROPERTY DAMAGE.
CAUTION:
CAUTION
THIS IS A GAME TABLE. DO NOT SIT, STAND, LEAN, WALK OR JUMP
ON TABLE! FAILURE TO COMPLY WITH THIS CAUTION COULD
RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE!

8
90 DAY LIMITED WARRANTY
This consumer warranty extends to the original consumer purchase of any ESCALADE®SPORTS Product
(hereinafter referred as the "Product").
WARRANTY DURATION: This Product is warranted to the original consumer purchase of a period of
ninety (90) days from the original purchase.
WARRANTY COVERAGE: ESCALADE SPORTS warrants to the original Consumer Purchaser that any
Product of its manufacture is free from defects in material and workmanship when used for the intended
purpose under normal use and conditions. THIS WARRANTY IS VOID IF THE PRODUCT HAS BEEN DAM-
AGED BY ACCIDENT, UNREASONABLE USE, NEGLIGENCE, IMPROPER SERVICE, FAILURE TO FOLLOW
INSTRUCTIONS PROVIDED WITH THE PRODUCT OR OTHER CAUSES NOT ARISING OUT OF
DEFECTS IN MATERIAL AND WORKMANSHIP.
WARRANTY PERFORMANCE: During the above ninety (90) day warranty period, ESCALADE SPORTS
shall repair or replace with a comparable model, and Product, or component thereof, which may prove
defective under normal use and proper care, and which our examination shall disclose to our satisfaction
to be thus defective, please contact our Warranty Dept.
1-800-426-1421 / Warranty Dept.
Or Write us at:
Escalade® Sports, Inc. - P.O. Box 889, Evansville, IN 47706 - Attn: Warranty Dept.
Or E-mail us at:
[email protected]
Other than shipping requirements no charge will be made for such repair or replacement of in-warranty
Products. ESCALADE® SPORTS strongly recommends that the Product is insured for value prior to mailing.
WARRANTY DISCLAIMERS: ANY IMPLIED WARRANTIES ARISING OUT OF THIS SALE, INCLUDING
BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PAR-
TICULAR PURPOSE, ARE LIMITED IN DURATION TO THE ABOVE NINETY (90) DAY WARRANTY PE-
RIOD. ESCALADE® SPORTS SHALL NOT BE LIABLE FOR LOSS OF USE OF THE PRODUCT OR OTHER
CONSEQUENTIAL OR INCIDENTAL COSTS, EXPENSES OR DAMAGES INCURRED BY THE CON-
SUMER OF ANY OTHER USE.
Some states do not allow the exclusion or limitation of implied warranties or consequential or incidental
damages, so the above limitations or exclusions may not apply to you.
LEGAL REMEDIES: This warranty gives you specific legal rights and you may also have other rights
which may vary from state to state.

9
CARE AND MAINTENANCE
You have purchased a quality product that will give you years of enjoyment. By following these simple maintenance steps, you will add to the life of
your new table.
THE TABLE TOP
The top (playing surface) of your table is made of particle board. Like all products made of wood, it can be affected by atmospheric changes in both
temperature and humidity. This may cause a slight sag or distortion as the top expands or contracts. This is normal and should not cause concern
as it does not detract from the play or utility value of the table. After assembly of the table, you can minimize the effects of temperature and humidity
changes by storing the table in the folded up position in a dry area when table is not in use.
STORAGE OF YOUR TABLE
This table must be stored indoors to prevent damage to the playing surface. Dampness and extreme temperature changes can cause the wood to
warp, swell, crack or blister. When your table is not in use, it should be folded up in a dry area. Due to the nature of particle board, table top may
bow. Damp and humid conditions will amplify this. This is normal and will not affect playability of table.
CLEANING YOUR TABLE
To clean your table use a soft, damp (NOT WET) cloth only. To prevent damage to your table's playing surface, DO NOT USE ANY CHEMICALS,
ABRASIVE OR CLEANING PRODUCTS on your table's playing surface.
MAINTENANCE OF YOUR TABLE
Be sure to oil all moving parts of your table including the pivot points. This will insure the safety and ease of use of your table.
This table must be kept indoors to prevent damage to the playing surface. Dampness and extreme temperature changes which occur on patios or
similar areas can cause wood to warp, swell, crack or blister.
UNLEVEL FLOORS
If table does not seem level, it is probably due to uneven or unlevel floors. Set the table in its PLAYING POSITION and move table several inches in
different directions to find the best location for the table. If the floor is extremely unlevel, table may not play or operate properly. If table is high in
the center, shim up under the outer U-legs.

10
1 4A-6552-00 4A-6596-00 Table Top 2
2 8S-6610-00 8S-6610-00 U-leg 2
3 2S-6387-02 2S-6387-02 U-Clip 12
4 8S-6605-00 8S-6605-00 Linkage 4
5 2S-6422-02 2S-6422-02 Name Panel 2
6 2S-6428-01 2S-6428-01 Safety Strap 2
7 8S-6606-00 8S-6606-00 U-support 2
8 2S-6264-02 2S-6264-02 Safety Latch 2
9 701-47 701-47 ¼-20 x 1½ Hex Head Bolt 6
10 801-120B 801-120B #10-24 x 3/4 Phil Rnd Hd Scr 2
11 2Q-6084-00 2Q-6084-00 Caster 4
12 3M-6115-00 3M-6115-00 Caster Socket 4
13 704-18 704-18 Leg Cap 4
14 701-82 701-82 ¼-20 x 2 Hex Head Bolt 4
15 701-26 701-26 ¼-20 Locknut 16
16 601-80B 601-80B #10-24 Locknut 2
PRODUCT PARTS LIST
2L-6795-00
Key # T8135 T8157 Description Qty.
T8165
17 701-1B 701-1B #10 Flatwasher 2
19 701-141 701-141 #8-32 x 1¼ Sheet Metal Screw 8
20 1B-6451-00 1B-6451-00 #8 x 7/16 Sheet Metal Screw 85
21 1B-6449-00 1B-6449-00 #8 x 5/8 Hex/Phil HD SMS 12
22 3M-6494-00 3M-6494-00 Corner Cap 4
23 1B-6191-00 1B-6191-00 1/4-20 X 2-3/4 Hex Head Bolt 4
24 2B-6087-00 2B-6087-00 Plastic Washer 10
25 2S-6384-00 2S-6384-00 3/4 Side Rail-Black 4
26 2S-6385-00 2S-6385-00 3/4 End Rail-black 2
27 5A-6700-00 5A-6700-00 Net and Post Kit 1
(Net and Post not included with T8157)
28 2L-6795-00 2L-6795-00 Owner’s Manual 1
29 1B-6465-00 1B-6465-00 1/4-20 X 1-3/4 Hex Head Bolt 2
30 7B-6257-00 7B-6257-00 5/16” Spacer 4
31 7B-6256-00 7B-6256-00 3/4” Spacer 4
Key # T8135 T8157 Description Qty.
T8165