STILLA Glendale User manual

STILLA
ASSEMBLY INSTRUCTIONS
‘Glendale’8x8
S3031
Every part needed to construct your shed is included inside the pack; cedar
panels, doors, windows, hardware kits & roof sheeting. Please ensure you fully
unpack all the parts & check against the parts checklist before contacting
customer service about anything you believe may be missing. Thank-you!

1 | P a g e
Caution
Please be careful when handling all components, some parts have sharp metal edges.
Always wear work gloves, eye protection and long sleeves when assembling or maintaining
your shed.
Tools required for assembly
•Level
•Drill
•Hammer
•Ladder
•12mm Drill bit
•6mm Drill bit
•Phillips head drive
•Hex Head Drive (5/16’)
•Safety glasses
•Gloves
Before assembly
•Remove all parts from packages and place in a safe place close to assembly area.
•Review all instructions; continue to refer to instructions throughout assembly –step
by step.
Preparing your site
•If you are installing your shed on the Stilla rebated floor we recommend finding a
place in your yard that is very close to level. Pavers or a solid material that will not be
affected by weather can be used to perfectly level the shed by placing under the
floor frame where required, make sure all members are supported.
•If you are installing your shed on the Stilla heavy duty floor, this can be placed on
unlevelled surfaces and levelled up by using the 100x100 stumps provided.

2 | P a g e
GLENDALE 8x8 PARTS CHECKLIST
Part Code
Checked
Part Description
Qty
P
Cedar Clad Panel 1200x1890mm
6
FP
Cedar Clad Panel 780x1890mm(480x1890mm if Double Doors)
2
G
8ft Gable
4
R
Rafters 1230x42x35mm
6
CD
Colonial Door 830x1875mm (714x1875mm if double doors)
1
C
2710mm Channel
2
TB/BB
Top Batten/Bottom Batten 2710mm
4
RS
1480mm Roof Sheeting
8
HK
8x8 Hardware Kit
1
RC
1520mm Ridge Cap
2
F
8ft Fascia Pack
1
CP
Corner Post 1890x61x18mm
4
CS
Cover Strip 1890x40x7mm
3
FGS
Front Gable Cover Strip –460mm
1
BGS
Back Gable Cover Strip –490mm
1
DS
Door Step 840x42x19mm (1440mm if double doors)
1
DH
Door Head 840x35x42mm (1440mm if double doors)
1
CT
Collar Tie 480mm
1
SCS
Stilla Cover Strip2400x40x7mm
1
IM
8x8 Instruction Manual
1
Floor Kit –Option
Floor Frame - (Rebated Floor 70x35mm/Heavy Duty Floor 140x35mm)
Part Code
Checked
Part Description
Qty
EP
End Plate 2470mm
2
DJ
Double Joist 2330mm
2
SJ
Single Joist 2330mm
4
L
Logs (light duty floor does not come with logs)
4
FN
Floor Nogs 460mm
6
FB
1798mm x 800mm
2
FB
597mm x 800mm
2
FB
1798mm x 711mm
1
FB
597mm x 711mm
1
8 Foot Loft Shelf - Option
Part Code
Checked
Part Description
Qty
8LS
8ft Loft Shelf
1
SS
8ft Loft Shelf Support
1

3 | P a g e
Double Doors –Option –Changes to above kit
Part Code
Part Description
Qty
CD
Colonial Door 714x1875mm
2
FP
Cedar Clad Panel 480x1890mm
2
DH
Double Door Head 1440x42x35mm
1
DS
Double Door Stop 1440x42x18mm
1
DP
Door Leaver Packer 100x100x18mm
1
8x8 Lean To –Option –Add Extra Screws
Part Code
Part Description
Qty
B
Beam 2710x70x35mm
1
VB
Verandah Beam 2710x140x35mm
1
VR
Verandah Rafter 1000x42x35mm
4
VP
Verandah Posts 2400mm
2
VF
Verandah Fascias 1100x75x20mm
2
VS
Verandah Roof Sheets 1150mm
4
8x8 Annex –Option –Add Extra Screws
Part Code
Part Description
Qty
B
Beam 2710x70x35mm
1
VB
Verandah Beam 2710x140x35mm
1
VR
Verandah Rafter 1930x42x35mm
4
VP
Verandah Posts 2400mm
2
VF
Verandah Fascias 2000x75x20mm
2
VS
Verandah Roof Sheets 2050mm
4

4 | P a g e
If no floor option was purchased, go to step 2.0 (Wall Assembly)
STEP 1.0
FLOOR KIT
1.0 –FLOOR KIT
PART CODE
QTY
DESCRIPTION
EP
2
End Plate 2470mm
SJ
4
Single Joist 2330mm
DJ
2
Double Joist 2330mm (42x35mm part of DJ goes at the top inside)
FN
6
Floor Nog
100BS
28
100mm Batten screw (Heavy Duty Floor Only)
75N
28
75mm Nail (Rebated Floor Only)
65HHS
12
65mm Hex Head Screw
1.0 –FLOOR FRAME
Fasten through EP into DJ using 3 x 100BS per join (75N on Rebated Floor)
Fasten through EP into SJ using 2 x 100BS per join (75N on Rebated Floor)
Fasten FN’s in positions shown below using 65HHS
Yellow Tongue

5 | P a g e
HEAVY DUTY FLOOR KIT
Heavy duty floor can be installed on unlevelled ground –use supplied logs to level your floor
by digging them into the ground.
Install heavy duty floor kit using (L) 4 logs –1 in each corner (position shown above) screw
through frame into log using 4 x 100BS per corner
Ensure floor frame is square by measuring from corner to corner diagonally prior to
installing flooring.
STEP 1.1
FLOORING INSTALLATION
1.1 –FLOOR INSTALLATION
PART CODE
QTY
DESCRIPTION
FB
2
Floor Board 1798x800mm
FB
2
Floor Board 597x800mm
FB
1
Floor Board 1798x711mm
FB
1
Floor Board 597x711mm
50PS
70
50mm Philips Screw
1.1 –FLOOR SHEETS
Fasten floor sheets to floor frame as shown below using 50PS

6 | P a g e
STEP 2.0
WALL ASSEMBLY
2.0 - ASSEMBLY PARTS –WALL ASSEMBLY
PART CODE
QTY
DESCRIPTION
FP
1
Front Wall panel
P
1
1200mm Wall panel
65HHS
3
65mm Hex head screw
-If optional window was purchased, it can take the place of any 1200mm (P) panel.
2.0 - ASSEMBLY –WALL ASSEMBLY
Screw through FP into P (top, centre & bottom) using 3 x 65HHS. (Holding studs flush on the
outside)
Note: Ensure tongue on VJ cladding is facing upwards.
P
Screw 3 x 65HHS (Top,
centre & bottom)
FP
Cedar Strip
When screwing the four corners together please make sure the studs are flush on the
outside (not the inside) as per image below.

7 | P a g e
STEP 2.1
WALL ASSEMBLY
2.1 - ASSEMBLY PARTS –WALL ASSEMBLY
PART CODE
QTY
DESCRIPTION
P
1
1200mm Wall panel
65HHS
3
65mm Hex head screw
2.1 - ASSEMBLY –WALL ASSEMBLY
Screw through P into P (Top, centre & bottom) using 3 x 65HHS, holding studs flush on the
inside.
P
Screw 3 x 65HHS (Top,
centre & bottom)
FRONT OF SHED
P

8 | P a g e
STEP 2.2
WALL ASSEMBLY
2.2 - ASSEMBLY PARTS –WALL ASSEMBLY
PART CODE
QTY
DESCRIPTION
P
1
1200mm Wall panel
65HHS
3
65mm Hex head screw
2.2 - ASSEMBLY –WALL ASSEMBLY
Screw through P into P (Top, centre & bottom) using 3 x 65HHS, holding studs flush on the
outside.
P
Screw 3 x 65HHS (Top,
centre & bottom)
FRONT OF SHED
P

9 | P a g e
STEP 2.3
WALL ASSEMBLY
2.3 - ASSEMBLY PARTS –WALL ASSEMBLY
PART CODE
QTY
DESCRIPTION
P
1
1200mm Wall panel
65HHS
3
65mm Hex head screw
2.3 - ASSEMBLY –WALL ASSEMBLY
Screw through P into P (Top, centre & bottom) using 3 x 65HHS, holding studs flush on the
inside.
P
Screw 3 x 65HHS (Top,
centre & bottom)
P
FRONT OF SHED

10 | P a g e
STEP 2.4
WALL ASSEMBLY
2.4 - ASSEMBLY PARTS –WALL ASSEMBLY
PART CODE
QTY
DESCRIPTION
P
1
1200mm Wall panel
65HHS
3
65mm Hex head screw
2.4 - ASSEMBLY –WALL ASSEMBLY
Screw through P into P (top, centre & bottom) using 3 x 65HHS holding studs flush on the
outside.
Screw 3 x 65HHS (Top,
centre & bottom)
P
P

11 | P a g e
STEP 2.5
WALL ASSEMBLY
2.5 - ASSEMBLY PARTS –WALL ASSEMBLY
PART CODE
QTY
DESCRIPTION
P
1
1200mm Wall panel
65HHS
3
65mm Hex head screw
2.5 - ASSEMBLY –WALL ASSEMBLY
Screw through P into P (top, centre & bottom) using 3 x 65HHS holding studs flush on the
inside.
Screw 3 x 65HHS (Top,
centre & bottom)
FRONT OF SHED
P
P

12 | P a g e
STEP 2.6
WALL ASSEMBLY
2.6 - ASSEMBLY PARTS –WALL ASSEMBLY
PART CODE
QTY
DESCRIPTION
FP
1
Front Wall panel
65HHS
3
65mm Hex head screw
2.6 - ASSEMBLY –WALL ASSEMBLY
Screw through FP into P (top, centre & bottom) using 3 x 65HHS holding studs flush on the
outside.
Screw 3 x 65HHS (Top,
centre & bottom)
Cedar Strip
FP
P

13 | P a g e
STEP 2.7
BACK GABLE ASSEMBLY
2.7 - ASSEMBLY PARTS –GABLE ASSEMBLY
PART CODE
QTY
DESCRIPTION
G
4
Gable (2 pairs)
65HHS
6
65mm Hex head screw
FGS
1
Front gable cover strip
SCS
1
Stilla branded cover strip
40N
10
40mm Nail
DH
1
Door head
2.7 - ASSEMBLY –GABLE ASSEMBLY
Lay both gable pairs on a flat surface with frame upwards. Hold flush at the bottom and
screw together using 2 x 65HHS in centre stud. (Image 1)
Turn one gable over. Position (SCS) Stilla branded cover strip flush with bottom cedar board
and flush on each end. Nail through cover strip into gable using 40N. (Image 2)
Position (FGS) front gable cover strip over join in front gable. Fasten in position using 40N.
(Image 3)
Hold DH (Door head) Perfectly centre of base plate on gable, screw down through gable
bottom plate into door head using 2 x 65HHS
1
2 3

14 | P a g e
STEP 2.8
FRONT GABLE ASSEMBLY
2.8 - ASSEMBLY PARTS –GABLE ASSEMBLY
PART CODE
QTY
DESCRIPTION
1
Assembled front gable
1
Assembled back gable
65HHS
7
65mm Hex head screw
2.8 - ASSEMBLY –GABLE ASSEMBLY
Carefully position front gable in position ensuring tongue on wall goes into groove on gable.
Fasten up through front panels using 2 x 65HHS either side. Repeat with back gable using 1 x
65HHS either side and centre.
Front gable has door head and Stilla strip.

15 | P a g e
STEP 3.0
ROOF ASSEMBLY
3.0 - ASSEMBLY PARTS –ROOF ASSEMBLY
PART CODE
QTY
DESCRIPTION
BB
1
Bottom batten
TB
1
Top batten
R
3
Rafter
100BS
6
100mm Batten screw
3.0 - ASSEMBLY –ROOF ASSEMBLY
Push R into BB and TB and insert 100BS into predrilled hole to fasten. 1 x 100BS per join.
TB
BB
R
R
R
TB
BB

16 | P a g e
STEP 3.1
ROOF ASSEMBLY
3.1 - ASSEMBLY PARTS –ROOF ASSEMBLY
PART CODE
QTY
DESCRIPTION
RS
2
1480mm sheet
40RS
2
40mm Roof screw
25RS
2
25mm Roof screw
3.1 - ASSEMBLY –ROOF ASSEMBLY
Lay roof frame on a hard surface. Position roof sheet’s (RS) flush at top and flush with end of
roof battens. Fasten roof sheets to roof frame in number sequence shown using 25RS at top
in pan and 40RS in rib at bottom.
Note: only screw in Pan at top and in rib at bottom.
TB BB
TB
Bent up edge at top.
Overhang
(TOP)
BB
1
2
3
4
Flush

17 | P a g e
STEP 3.2
ROOF ASSEMBLY
3.2 - ASSEMBLY PARTS –ROOF ASSEMBLY
PART CODE
QTY
DESCRIPTION
RS
2
1480mm roof sheet
40RS
3
40mm Roof screw
25RS
6
25mm Roof Screw
3.2 - ASSEMBLY –ROOF ASSEMBLY
Complete laying roof sheeting out on frame. Fasten roof sheets to battens in sequence
shown. 1 x 25RS either side of join at top and 1 x 40RS through rib join at bottom.
Bent up edge at top.
(TOP)
1
2
3
4
6
5

18 | P a g e
STEP 3.3
ROOF ASSEMBLY
3.3 - ASSEMBLY PARTS –ROOF ASSEMBLY
PART CODE
QTY
DESCRIPTION
40RS
16
40mm Roof screw
25RS
16
25mm Roof screw
3.3 - ASSEMBLY –ROOF ASSEMBLY
Complete screwing roof off at top. 1 x 25RS in pan beside every rib. Once top complete
screw bottom off using 1 x 40RS in every rib.
Note: Use straight edge to keep al screws in line and centre of batten
Bent up edge at top.
(TOP)

19 | P a g e
STEP 3.4
CHANNEL ASSEMBLY
If you purchased the Lean-To/Annex, leave the channel off the side you will be installing
your Lean-To/Annex
3.4 - ASSEMBLY PARTS –CHANNEL ASSEMBLY
PART CODE
QTY
DESCRIPTION
ST
7
12mm self tapping screw
C
1
2.71m Channel
3.4 - ASSEMBLY –CHANNEL ASSEMBLY
Fasten capping C to roof using 5 x ST.
REPEAT TASKS 3.0 –3.4 TO COMPLETE THE OTHER ROOF PANEL.
Bent up edge at top.
(TOP)