STILLA Oxford User manual

STILLA
ASSEMBLY INSTRUCTIONS
‘Oxford’ 6x9
S3021
Every part needed to construct your shed is included inside the pack; cedar
panels, doors, windows, hardware kits & roof sheeting. Please ensure you fully
unpack all the parts & check against the parts checklist before contacting
customer service about anything you believe may be missing. Thank-you!

1 | P a g e
Caution
Please be careful when handling all components, some parts have sharp metal edges.
Always wear work gloves, eye protection and long sleeves when assembling or maintaining
your shed.
Tools required for assembly
•Level
•Drill
•Hammer
•Ladder
•Phillips head drive
•Hex Head Drive (5/16’)
•Safety glasses
•Gloves
Before assembly
•Remove all parts from packages and place in a safe place close to assembly area.
•Check all parts on assembly parts list are included, prior to commencing assembly.
•Review all instructions; continue to refer to instructions throughout assembly –step
by step.
Preparing your site
•Choose your site carefully, site surface must be level (unless a Elevation kit or Heavy
duty floor kit option has been purchased with your product)

2 | P a g e
OXFORD 6x9 PARTS CHECKLIST
Part Code
Checked
Part Description
Qty
P
Cedar Clad Panel 900x1890mm
7
WP
Cedar Clad Window Panel 900x1890mm
1
FP
Cedar Clad Panel 480x1890mm (180x1890mm if Double Doors)
2
FG
6ft Front Gable
1
BG
6ft Back Gable
1
R
Rafters 900x42x35mm
6
CD
Colonial Door 830x1875mm
1
C
3000mm Channel
2
TB/BB
Top Batten/Bottom Batten 3000mm
4
RS
1150mm Roof Sheeting
8
HK
6x9 Hardware Kit
1
RC
1800mm Ridge Cap
2
F
6ft Fascia Pack
1
CP
Corner Post 1890x60x18mm
4
CS
Cover Strip 1890x40x7mm
5
DS
Door Step 840x19x42mm (1440mm if double doors)
1
DH
Door Head 840x42x35mm (1440mm if double doors)
1
CT
Collar Tie 480mm
1
IM
6x9 Instruction Manual
1
Floor Kit –Option
Floor Frame - (Rebated Floor 70x35mm/Heavy Duty Floor 140x35mm)
Part Code
Checked
Part Description
Qty
EP
End Plate 1870mm
2
DJ
Double Joist 2630mm
2
SJ
Single Joist 2630mm
3
L
Logs (rebated floor does not come with logs) 750mm
6
FB
1798x800mm
3
FB
1798x211mm
1
6 Foot Loft Shelf - Option
Part Code
Checked
Part Description
Qty
6LS
6ft Loft Shelf
1

3 | P a g e
Double Doors –Option –Changes to above kit
Part Code
Checked
Part Description
Qty
CD
Colonial Door 714x1875mm
2
FP
Double Door Panel 180x1890mm
2
DP
Door Leaver Packer 100x100x18mm
1
DH
Door Head 1440x42x35mm
1
DS
Door Stop 1440x42x18mm
1
6x9 Lean To –Option –Add Extra Screws
Part Code
Checked
Part Description
Qty
B
Beam 3000x70x35mm
1
VB
Verandah Beam 3000x140x35mm
1
VR
Verandah Rafter 1000x42x35mm
4
VP
Verandah Posts 2400mm
2
VF
Verandah Fascias 1100x75x20mm
2
VS
Verandah Roof Sheets 1150mm
4
6x9 Annex –Option –Add Extra Screws
Part Code
Checked
Part Description
Qty
B
Beam 3000x70x35mm
1
VB
Verandah Beam 3000x140x35mm
1
VR
Verandah Rafter 1930x42x35mm
4
VP
Verandah Posts 2400mm
2
VF
Verandah Fascias 2000x75x20mm
2
VS
Verandah Roof Sheets 2050mm
4

4 | P a g e
If no floor option was purchased, go to step 2.0 (Wall Assembly)
STEP 1.0
FLOOR KIT
1.0 –FLOOR KIT
PART CODE
QTY
DESCRIPTION
EP
2
End Plate 1870mm
SJ
3
Single Joist 2630mm
DJ
2
Double Joist 2630mm (42x35mm part of DJ goes at the top, inside)
100BS
24
100mm Batten screw (Heavy Duty Floor Only)
75N
24
75mm Nail (Rebated Floor Only)
1.0 –FLOOR FRAME
Fasten through EP into DJ using 3 x 100BS per join (75N on Rebated Floor)
Fasten through EP into SJ using 2 x 100BS per join (75N on Rebated Floor)
HEAVY DUTY FLOOR KIT
Heavy duty floor can be installed on unlevelled ground –use supplied logs to level your floor
by digging them into the ground.
Install heavy duty floor kit using (L) 4 logs –1 in each corner (position shown above) screw
through frame into log using 4 x 100BS per corner
Ensure floor frame is square by measuring from corner to corner diagonally prior to
installing flooring.
Yellow Tongue
DJ
DJ
SJ
SJ
SJ

5 | P a g e
STEP 1.1
FLOORING INSTALLATION
1.1 –FLOOR INSTALLATION
PART CODE
QTY
DESCRIPTION
FB
3
Floor Board 1798x800mm
FB
1
Floor Board 1798x211mm
50PS
70
50mm Philips Screw
1.1 –FLOOR SHEETS
Fasten floor sheets to floor frame as shown below using 50PS –Note, there are now 4
sheets on the Oxford floor –the above is correct.

6 | P a g e
STEP 2.0
WALL ASSEMBLY
WALL PANEL WP (900MM WINDOW PANEL) CAN BE POSITIONED ANYWHERE ON THE SHED
WHERE WE HAVE USED A P (900MM WALL PANEL).
2.0 - ASSEMBLY PARTS –WALL ASSEMBLY
PART CODE
QTY
DESCRIPTION
FP
1
Front Wall panel
P
1
900mm Wall panel
65HHS
3
65mm Hex head screw
2.0 - ASSEMBLY –WALL ASSEMBLY
Screw through FP into P (top, centre & bottom) using 3 x 65HHS. (Holding studs flush on the
outside)
P
Screw 3 x 65HHS (Top,
centre & bottom)
FP
Cedar Strip

7 | P a g e
STEP 2.1
WALL ASSEMBLY
2.1 - ASSEMBLY PARTS –WALL ASSEMBLY
PART CODE
QTY
DESCRIPTION
P
1
900mm Wall panel
65HHS
3
65mm Hex head screw
2.1 - ASSEMBLY PARTS –WALL ASSEMBLY
Screw through P into P (Top, centre & bottom) using 3 x 65HHS, holding studs flush on the
inside.
P
Screw 3 x 65HHS (Top,
centre & bottom)
P

8 | P a g e
STEP 2.2
WALL ASSEMBLY
2.2 - ASSEMBLY PARTS –WALL ASSEMBLY
PART CODE
QTY
DESCRIPTION
P
1
900mm Wall panel
65HHS
3
65mm Hex head screw
2.2 - ASSEMBLY PARTS –WALL ASSEMBLY
Screw through P into P (Top, centre & bottom) using 3 x 65HHS, holding studs flush on the
inside.
P
Screw 3 x 65HHS (Top,
centre & bottom)
P

9 | P a g e
STEP 2.3
WALL ASSEMBLY
2.3 - ASSEMBLY PARTS –WALL ASSEMBLY
PART CODE
QTY
DESCRIPTION
P
1
900mm Wall panel
65HHS
3
65mm Hex head screw
2.3 - ASSEMBLY PARTS –WALL ASSEMBLY
Screw through P into P (Top, centre & bottom) using 3 x 65HHS, holding studs flush on the
outside.
P
Screw 3 x 65HHS (Top,
centre & bottom)
P

10 | P a g e
STEP 2.4
WALL ASSEMBLY
2.4 - ASSEMBLY PARTS –WALL ASSEMBLY
PART CODE
QTY
DESCRIPTION
P
1
900mm Wall panel
65HHS
3
65mm Hex head screw
2.4 - ASSEMBLY PARTS –WALL ASSEMBLY
Screw through P into P (top, centre & bottom) using 3 x 65HHS holding studs flush on the
inside.
P
Screw 3 x 65HHS (Top,
centre & bottom)
P

11 | P a g e
STEP 2.5
WALL ASSEMBLY
2.5 - ASSEMBLY PARTS –WALL ASSEMBLY
PART CODE
QTY
DESCRIPTION
P
1
900mm Wall panel
65HHS
3
65mm Hex head screw
2.5 - ASSEMBLY PARTS –WALL ASSEMBLY
Screw through P into P (top, centre & bottom) using 3 x 65HHS holding studs flush on the
outside.
P
Screw 3 x 65HHS (Top,
centre & bottom)
P

12 | P a g e
STEP 2.6
WALL ASSEMBLY
2.6 - ASSEMBLY PARTS –WALL ASSEMBLY
PART CODE
QTY
DESCRIPTION
WP
1
900mm Window panel
65HHS
3
65mm Hex head screw
2.6 - ASSEMBLY PARTS –WALL ASSEMBLY
Screw through WP into P (top, centre & bottom) using 3 x 65HHS holding studs flush on the
inside.
P
Screw 3 x 65HHS (Top,
centre & bottom)
WP

13 | P a g e
STEP 2.7
WALL ASSEMBLY
2.7 - ASSEMBLY PARTS –WALL ASSEMBLY
PART CODE
QTY
DESCRIPTION
P
1
900mm Wall panel
65HHS
3
65mm Hex head screw
2.7 - ASSEMBLY PARTS –WALL ASSEMBLY
Screw through P into P (top, centre & bottom) using 3 x 65HHS holding studs flush on the
inside.
P
Screw 3 x 65HHS
(Top, centre &
bottom)
P

14 | P a g e
STEP 2.8
WALL ASSEMBLY
2.8 - ASSEMBLY PARTS –WALL ASSEMBLY
PART CODE
QTY
DESCRIPTION
FP
1
Front Wall panel
65HHS
3
65mm Hex head screw
2.8 - ASSEMBLY PARTS –WALL ASSEMBLY
Screw through FP into P (top, centre & bottom) using 3 x 65HHS holding studs flush on the
inside.
P
Screw 3 x 65HHS
(Top, centre &
bottom)
FP
Cedar Strip

15 | P a g e
STEP 3.0
BACK GABLE ASSEMBLY
3.0 - ASSEMBLY PARTS –GABLE ASSEMBLY
PART CODE
QTY
DESCRIPTION
BG
1
Back gable
65HHS
3
65mm Hex head screw
3.0 - ASSEMBLY PARTS –GABLE ASSEMBLY
Carefully position BG in place inserting tongue on back panels into groove in BG. Screw up
through wall panels into bottom plate of gable using 3 x 65HHS. (evenly spread screws
across the length of the gable)

16 | P a g e
STEP 3.1
FRONT GABLE ASSEMBLY
3.1 - ASSEMBLY PARTS –GABLE ASSEMBLY
PART CODE
QTY
DESCRIPTION
FG
1
Front gable
65HHS
4
65mm Hex head screw
3.1 - ASSEMBLY PARTS –GABLE ASSEMBLY
Carefully position FG in place inserting tongue on front walls into groove in FG. Screw up
through wall panels into bottom plate of gable using 4 x 65HHS. (2 in each side)
STEP 3.2
DOOR HEAD ASSEMBLY
3.2 - ASSEMBLY PARTS –DOOR HEAD ASSEMBLY
PART CODE
QTY
DESCRIPTION
DH
1
Door Head
65HHS
2
65mm Hex Head Screw
3.2 - DOOR HEAD ASSEMBLY
Place door head in position at top of door opening between front FP’s. Screw down through
front gable into door head using 2 x 65HHS.

17 | P a g e
STEP 3.3
ROOF ASSEMBLY
3.3 - ASSEMBLY PARTS –ROOF ASSEMBLY
PART CODE
QTY
DESCRIPTION
BB
1
Bottom batten
TB
1
Top batten
R
3
Rafter
100BS
6
100mm Batten screw
3.3 - ASSEMBLY –ROOF ASSEMBLY
Push R into BB and TB and insert 100BS into predrilled hole to fasten. 1 x 100BS per join.
TB
BB
R
R
R
TB

18 | P a g e
STEP 3.4
ROOF ASSEMBLY
3.4 - ASSEMBLY PARTS –ROOF ASSEMBLY
PART CODE
QTY
DESCRIPTION
RS
2
Roof sheets
40RS
2
40mm Roof screw
25RS
2
25mm Roof screw
3.4 - ASSEMBLY –ROOF ASSEMBLY
Lay roof on a hard surface. Position 1 roof sheet (RS) at each end of frame flush at top and
flush with end of roof battens. Fasten roof sheets to roof frame in number sequence shown
using 40RS into bottom batten and 25RS into top batten.
Note: only screw in Pan at top and in rib at bottom.
TB
Bent up edge at top.
Overhang
(TOP)
BB
1
2
3
4
Flush

19 | P a g e
STEP 3.5
ROOF ASSEMBLY
3.5 - ASSEMBLY PARTS –ROOF ASSEMBLY
PART CODE
QTY
DESCRIPTION
RS
2
1150mm Roof sheet
40RS
3
40mm Roof screw
25RS
6
25mm Roof screw
3.5 - ASSEMBLY –ROOF ASSEMBLY
Complete laying roof sheeting out on frame. Fasten roof sheets to battens in sequence
shown. 1 x 25RS either side of join at top and 1 x 40RS through rib join at bottom.
Bent up edge at top.
(TOP)
1
2
3
4
6
5