Sting KC Cobra Administrator Guide

SERVICE AND TECHNICAL SUPPORT CALL: FAMILY FUN COMPANIES [phone] WWW.FAMILYFUNCOMPANIES.COM
GAME OPERATION & INSTRUCTION MANUAL
FOR ALL PARTS, SERVICE, AND TECHNICAL SUPPORT
PHONE: [phone] FAX: [phone]
WWW.FAMILYFUNCOMPANIES.COM
STING INTERNATIONAL, © 2013 ALL RIGHTS RESERVED

SERVICE AND TECHNICAL SUPPORT CALL: FAMILY FUN COMPANIES [phone] WWW.FAMILYFUNCOMPANIES.COM
THIS GAME IS INTENDED FOR INDOOR USE ONLY

SERVICE AND TECHNICAL SUPPORT CALL: FAMILY FUN COMPANIES [phone] WWW.FAMILYFUNCOMPANIES.COM
CONTENTS
1. SPECIFICATION ................................................................................................................. 1
2. INTRODUCTION ................................................................................................................. 2
2-1 OVERVIEW .................................................................................................................. 2
2-2 IMPORTANT SAFETY INFORMATION ....................................................................... 3
2-3 SET UP......................................................................................................................... 3
3. PACKAGE CONTENTS ...................................................................................................... 4
4. INSTALLATION .................................................................................................................. 4
4-1 LOCATIONS TO AVOID............................................................................................... 5
4-2 INSTALLING AT SITE .................................................................................................. 5
5. CONNECTING THE POWER CORD .................................................................................. 6
5-1 WIRE HOLDER ............................................................................................................ 6
6. PARTS DESCRIPTION ....................................................................................................... 7
6-1 GAME APPEARANCE and FEATURES ...................................................................... 7
6-2 TICKET MECHANISM（ENTROPY）......................................................................... 8
6-3 BILL ACCEPTOR OPTION (OPERATOR INSTALLED) .............................................. 9
6-4 COIN MECHANISM（MECHANICAL）D-200 ........................................................... 12
6-5 COIN MECHANISM（ELECTRONIC)........................................................................ 12
6-6 TRUNK ....................................................................................................................... 14
7. SERVICE ............................................................................................................................. 15
8. CONTROL SIGNAL AND INSTRUCTION ........................................................................ 18
8-1 PCB LAYOUT ............................................................................................................. 18
8-2 HOW TO ENTER INTO MENUS ................................................................................ 19
9. INSTRUCTION OF GAME PLAY...................................................................................... 24
10. GENERAL TROUBLESHOOTING.................................................................................... 26
11. PART LIST ........................................................................................................................ 27
11-1 BASE MECHANICAL ASSY ..................................................................................... 27
11-2 HARDWARE COMPONENT .................................................................................... 29
11-3 MACHINE PARTS LIST............................................................................................ 29!

SERVICE AND TECHNICAL SUPPORT CALL: FAMILY FUN COMPANIES [phone] WWW.FAMILYFUNCOMPANIES.COM
1
1. SPECIFICATION
(1) Dimension: L2070mm，W1080mm，H1170mm
W43” x D81” x H44”
(2) Weight: 164KG 331 Lbs.
(3) Voltage: AC 110V -120V, 220-240V 50Hz-60Hz；
(4) Power: 68W-500W（when playing, the more load, the higher the power required）
(5) Current：0.9A-10A
Note：Please refer to the nameplate at the back of game for the actual voltage
(6) Environment: (indoor) temperature -10+40; humidity ≤90% ; pressure 86Pa106Pa
Note: Game parameters are subject to change without notice.

SERVICE AND TECHNICAL SUPPORT CALL: FAMILY FUN COMPANIES [phone] WWW.FAMILYFUNCOMPANIES.COM
2
2. INTRODUCTION
2-1 OVERVIEW
Thank you for purchasing the KC-COBRA video game ride.
This owner’s Manual is intended to provide detailed descriptions together with all the
necessary information regarding the general operation of electronic assemblies, servicing
control, spare parts, etc., pertaining to the game.
This manual is intended for the owner, operator, personnel and managers in charge of
operation of the product. Operate the product after carefully reading and sufficiently
understanding the instructions. If the product fails to function satisfactorily, non-technical
personnel should under no circumstances attempt to service the internal system.
To Maintain Safety:
To ensure the safe usage of the product, be sure to read the following before using the
product. The following instructions are intended for the users, operators and the personnel in
charge of the operation of the product. After carefully reading and sufficiently understanding the
warning display and cautions, handle the product appropriately. Be sure to keep this operation
manual nearby the product or elsewhere convenient for referring to it when necessary.
For the safe usage of the product, the following pictographs are used:
Indicates: “HANDLE WITH CARE”. In order to protect the human body and equipment,
this display is attached to places where the instruction manual should be referred to.
Indicates: a “PROTECTIVE EARTH TERMINAL”. Before operating the equipment, be
sure to connect it to the ground. (The step may be omitted for products in which a power cable
with earth is used.)
Be sure to understand the contents of the displays before operating the equipment or
reading the text.
DANGER
WARNING
CAUTION
Indicates that mishandling the product by disregarding this pictograph
may cause severe injury or even death.
Indicates that mishandling the product by disregarding this warning may
cause a potentially hazardous situation which can result in death or
serious injury.
Indicates that mishandling the product by disregarding this caution may
cause a slight hazardous situation which can result in personal injury
and/or material damage.

SERVICE AND TECHNICAL SUPPORT CALL: FAMILY FUN COMPANIES [phone] WWW.FAMILYFUNCOMPANIES.COM
3
2-2 IMPORTANT SAFETY INFORMATION
Unplug the game from the AC wall receptacle when servicing this product. Failure to do so
could result in serious injury to yourself or others.
Use only a GROUNDED AC receptacle. Failure to do so could result in improper operation
or damage to the game and could void your warranty. If you are unsure that your AC
receptacle is properly grounded, have a qualified electrician perform this check for you.
Always be sure power to the game is turned off when doing even routine maintenance
otherwise, moving parts could activate unexpectedly causing injury.
This product is heavy, necessitated by the design. When moving this game, be sure you
have adequate help. Use a suitable dolly or hand truck where practical.
2-3 SET UP
Be sure that the game is on a level surface. If the game is rocking unevenly on the floor
adjust the legs to remove the rocking of the game.
Be sure to plug the game into the proper A.C. GROUNDED receptacle. Do not use long
extension cords unless absolutely necessary and if so, be sure it is a heavy duty cord of at
least 16 Ga. and no longer than 20 ft. Check the label on the back of the game to make
sure the power requirements of the game match that of your location.
Turn the game on and check to be sure there are no unusual sounds and that everything
appears to be working correctly.

SERVICE AND TECHNICAL SUPPORT CALL: FAMILY FUN COMPANIES [phone] WWW.FAMILYFUNCOMPANIES.COM
4
3. PACKAGE CONTENTS
Be sure to check that you have received all packages indicated below.
Game Unit
Accessories
No.
Name
Specification
Picture
Qty.
Remark
1
Manual
1
English version
2
Key
GUO711
2
Ticket door、coin door、
coin box、service door
3
Power
cord
UL/CE Version
1
Per request
4
Fuse
10A
1
This machine has included an additional “U” disc for situations caused by power surges.
Function
In the event of a sudden surge of power, the video may freeze or the game may
not log in normally. In this case, please take this U disc which is found next to the
main PC and insert into USB port on host PC. After inserting, game system
software will be reinitialized automatically. After installing, game will run normally.
Please put U disc back into the storage port for future use if necessary.
4. INSTALLATION
Check the parts list before installation. Verify that all parts that have been received and are in
good condition
For indoor use only!
。
ATTENTION

SERVICE AND TECHNICAL SUPPORT CALL: FAMILY FUN COMPANIES [phone] WWW.FAMILYFUNCOMPANIES.COM
5
4-1 LOCATIONS TO AVOID
4-2 INSTALLING ON SITE
The machine must be fixed on level ground. The product is equipped with 4 casters and 4
adjusters. When installation position /site has been determined, have the adjusters come in
direct contact with the floor.
Establish a gap of about 5 mm between the floor and the casters and adjust the unit so that it
will remain level.
Move the product to the installation site.
Bring the adjusters into direct contact with the floor. Use a wrench to align the height of the
adjusters until the cabinet is perfectly level.
After setting, turn adjuster nuts upwards to tighten them and secure adjuster heights.
The machine is designed for indoor use only. Never install this machine
outdoors or in any of the following:
●Locations exposed to direct sunlight
●Locations subject to rain or water leakage.
●Unstable locations or locations subject to vibration.
●Dusty, hot, or damp locations.
WARNING

SERVICE AND TECHNICAL SUPPORT CALL: FAMILY FUN COMPANIES [phone] WWW.FAMILYFUNCOMPANIES.COM
6
5. CONNECTING THE POWER CORD
5-1 WIRE HOLDER
WARNING
●Do not put heavy items on power cord.
Disconnect game power before moving.
Make sure all wheels are intact. Replace any wheels that are damaged or
broken before moving the game.
When moving the game, DO NOT slide the game across the floor.
Ensure the game is level before connecting the power.
To insure a long life of your product we recommend always wrapping the
game with soft blankets for moving long distance to protect the finish.
WIRE
HOLDER
BASE
PLUG
SOCKET
PLUG
POWER
SWITCH
IEC SOCKET
WARNING

SERVICE AND TECHNICAL SUPPORT CALL: FAMILY FUN COMPANIES [phone] WWW.FAMILYFUNCOMPANIES.COM
7
●Hold the power plug instead of the wire to draw the power cord out of the socket.
●Do not touch the power plug with wet hands.
●Do not draw or twist the cord or store near any high heat source.
●Do not place the cord where the player can easily trip over, or come in contact with it.
●Operate this game with the correct power and fuse configuration.
6. PARTS DESCRIPTION
6-1 GAME APPEARANCE AND FEATURES

SERVICE AND TECHNICAL SUPPORT CALL: FAMILY FUN COMPANIES [phone] WWW.FAMILYFUNCOMPANIES.COM
8
1 BASE：Base Mech
2 PROTECTION SKIRT：Prevent Player from reaching base
3 FIBERGLASS CAR：Main game（KC COBRA）
4 CHROME WHEEL COVER: Decoration
5 19”LCD MONITOR：For game video
6 STEERING WHEEL：Control car on video to move left and right
7 “JUMP” BUTTON：Press JUMP Button to jump car on video
8 TICKET/ DBV DOOR ：For ticket version or DBV version. Key GUA71.
9 COIN DOOR：Key GUA711
10 COIN BOX：Key GUA711, collect coin.
11 GAS PEDAL：Increment the speed of the car in the video.
12 SPEAKER COVER：Protects the audio speakers.
13 TRUNK：Key GUA711, reach to mainboard, amplifier board, main motor.
6-2 TICKET MECHANISM（ENTROPY）
How to fill the ticket
Open the Ticket Door, place the Tickets into the TICKET HOLDER.
Feed the Tickets into the TICKET MECH.
①Unclip and remove the Ticket retainier
Picture 1 Picture 2
For Ticket version only!
。
NOTE

SERVICE AND TECHNICAL SUPPORT CALL: FAMILY FUN COMPANIES [phone] WWW.FAMILYFUNCOMPANIES.COM
9
Feed the tickets into the mechanism making sure that the ticket passes through the sensor.
Replace the ticket retainer to secure tickets into position.
Press the TEST button on the PCB to draw tickets through the mechanism and out of the door.
Close the Ticket Door, tear off any excess tickets.
.
6-3 BILL ACCEPTOR (DBV) OPTION
Maintenance
To make sure the bill acceptor always works smoothly, please clean the internal parts every
two weeks to every two months.
To clean the internal parts:
For DBV version only!
。
NOTE

SERVICE AND TECHNICAL SUPPORT CALL: FAMILY FUN COMPANIES [phone] WWW.FAMILYFUNCOMPANIES.COM
10
1. Press the buttons on the sides of bill path unit and pull the unit out.
2. Use a soft, dry cloth or towel to clean the bill path and sensors.
Trouble Shooting (Continuedonthenextpage)
Do not use an organic solvent such as gasoline or paint thinner to clean the unit.
CAUTION

SERVICE AND TECHNICAL SUPPORT CALL: FAMILY FUN COMPANIES [phone] WWW.FAMILYFUNCOMPANIES.COM
11
DIAGNOSTICS Bezel LED (Green LED)
LED ON = OK
LED OFF =POWER OFF
LED Flashes
Status
Corrective Actions
1
Bill jammed
Remove the bill box by sliding
the top button and the bill path
unit (as above figure), and then
remove the jammed bill.
2
Disable
Inspect for right DIP switch
setting.
3
Recognition sensor error.
Inspect for foreign objects on
sensor or bill path and clean.
3+2
Hook sensor error.
Inspect for foreign objects on
security

SERVICE AND TECHNICAL SUPPORT CALL: FAMILY FUN COMPANIES [phone] WWW.FAMILYFUNCOMPANIES.COM
12
3+5
(Optional)
Out sensor error.
Inspect for foreign objects on
sensor or bill path and clean.
5
Bill box has been removed.
Replace the bill box.
6
Stacker error or stacker full.
Empty the bill box.
7
Motor error.
Inspect for foreign objects on bill
path and clean.
6-4 COIN MECH（MECHANICAL）D-200
(Aluminum; adjustment, reject iron material coin)
Scope of dimension ：D=25mm-25.5mm, T=1.8mm
DC12V+/-2V,temperature -30-+120°；
1. COIN SLOT, 2. REJECT BUTTON, 3. REJECT SLOT, 4. COIN SWITCH
5. SCREW FOR ADJUSTMENT, 6. ADJUSTMENT ROD, 7. SET SCREW
Press Reject Button, the jamming coin will come out of the Reject Slot. If the coin does not
come out after pressing the Reject Button, please take apart the mechanism to take out the
jammed coin.
Note: please cut off the power before taking out the coin Mechanism.
Adjustment: Loosen screw # 5, move rod #6 up and down per coin dimension. Adjust the fixed
sheet at the back of mechanism by screw #7 to avoid coin jamming.
6-5 COIN MECH（ELECTRONIC)

SERVICE AND TECHNICAL SUPPORT CALL: FAMILY FUN COMPANIES [phone] WWW.FAMILYFUNCOMPANIES.COM
13
INSTRUCTION OF ELECTRONIC COIN COMPARATOR TYPE
Continued on the following page;
A. REMOVE THE PLASTIC COIN FROM COIN SLOT,
REPLACE WITH THE DESIRED TOKEN OR COIN INSIDE
THE SPRING TENSIONED COIN HOLDER.
B. LOOSEN BOLTS AT THE BACK OF COIN ENTRANCE. USE THE DESIRED COIN
DIAMETER TO ADJUST SPACE AT THE BACK OF COIN ENTRANCE. AVOID ERROR
CAUSED BY LARGE DIAMETER TOKENS.
C. ADJUST FOR GAME MAIN BOARD PULSE RATE NEEDS. CHOOSE COIN LONG
SHORT AND FAST SLOW THREE PHASE SWITCH (TIMER SWITCH）：30MS IS SHORT
FAST SIGNAL BEST FOR MACHINE THAT HAS HIGH POWER AND REQUIRES THE
INSERT OF COIN QUICKLY, 50MS IS MIDDLE SIGNAL, BEST FOR ORDINARY MACHINES
(IF NOT SPECIAL CIRCUMSTANCE, THE MACHINE USUALLY CAN USE THIS PHASE).
100MS IS LONG, SLOW SIGNAL, BEST FOR MACHINE THAT DOES NOT NEED INSERT
TO COINS QUICKLY.
D. VR COIN CHOOSE SENSITIVITY ADJUSTMENT，ANTICLOCKWISE ADJUSTMENT（—），
ACCEPT SMALLER AREA OF COIN TOLERANCE，COIN TYPE FILTRATION WILL BE
MORE RESTRICTED.
Wiring：
Grey
Red -DC+12V
White –COIN signal
Code Table
Black-Grounded
Grey

SERVICE AND TECHNICAL SUPPORT CALL: FAMILY FUN COMPANIES [phone] WWW.FAMILYFUNCOMPANIES.COM
14
6-6 TRUNK
SERVICE DOOR KEY GUA711, open the service door to service the computer host,
circuit board etc
HOST COMPUTER
1 POWER INLET
2 CVI
3 VGA
4 NETWORK CONNECTION
5 USB（4PCS）
6 AUDIO CONNECTION
SERVICE DOOR
1
2
3
4
5
6
MAIN FRAME
MAIN
BOARD

SERVICE AND TECHNICAL SUPPORT CALL: FAMILY FUN COMPANIES [phone] WWW.FAMILYFUNCOMPANIES.COM
15
7. SERVICE
Please remove fiberglass car body completely off when servicing the base. When removing the
body to access the base you should follow the instructions below.
1. Turn off power, unscrew screws around skirt and remove the skirt
2. Open back door, disconnect ALL connectors at both sides . See instruction below
Disconnect the connector
at left side to separate
fiberglass and electrical
parts
Disconnect connector
at right side to
separate motor and
power

SERVICE AND TECHNICAL SUPPORT CALL: FAMILY FUN COMPANIES [phone] WWW.FAMILYFUNCOMPANIES.COM
16
3. Unscrew and remove the 2 screws on fixed board, and slide (pull) out fixed board and the
all electrical parts on it. See the circle on picture
4. Look through the empty back door, you can see the long screw which fastens the fiberglass
car and base. Take out this long screw. See the circle on picture
5. Unscrew 4 screws on aluminum plate.
Move out
Allen key

SERVICE AND TECHNICAL SUPPORT CALL: FAMILY FUN COMPANIES [phone] WWW.FAMILYFUNCOMPANIES.COM
17
6. With two persons assisting, carefully raise up the fiberglass car and remove it from base. (2
persons are necessary to raise up the fiberglass car body)
7. Service the base assembly mechanism and motor after removing the fiberglass car body.
NOTE：
When replacing the fiberglass car back on the base, you should carefully align the 4 screw
holes on fiberglass step plate and the 4 screw holes on the base.
Please use caution in connecting the connectors in the proper place.