Stoane Lighting Mole User manual

Mole
Installation and maintenance
instructions
IMPORTANT: All wiring connections must be made before switching on mains power.
IP66 Dust tight and protected against powerful jets of water. Suitable for Exterior Use
Class III - Extra-low voltage
This product should not be disposed of in your general waste
Please retain these instructions for future reference
European Conformity
MSL Star Oslon Square 2.9VF2W @ 700mA
1
410 381 1497 inter-lux.com [email protected]
Inter-lux reserves the right to make technical changes without notice.
STOANE LIGHTING

FIXING
Check that the mounting surface is suitable for the
installation of this fitting.
A 33mm diameter hole is required for this fitting.
Step 1 Make mains connections to SELV LED driver
and extra low voltage connections to the
fitting.
Step 2 Insert cables through mounting hole, press
the fin in and push into the hole. The fin
should spring out holding the fitting in place.
Secure unit in place using silicone adhesive or similar
if the fitting is not supplied with a ‘fin’.
If using the ‘fin’ retaining method in walls/ceiling
thinner that 9mm then an adhesive may be required to
secure fitting.
After opening the sealed portion of the luminaire for
any reason, MSL recommends running the fitting for
15 minutes with the lid open to expel moisture before
closing it up. This will prevent condensation on the
lens and protect the fitting from corrosion.
WARNING: Do not look at exposed LED lamps in
operation. Eye injury can result.
Cleaning:
Fully isolate the fitting and allow to cool.
Clean the fitting with a slightly damp lint free cloth
from a mild solution of soap and water. The fitting
must be completely dry before reconnecting power.
Incompatible or abrasive chemicals can damage the
fitting, contact MSL for advice if required.
SUPPLY
Installation must be carried out by a qualified electrician in
accordance with BS 7671:2008 Wiring Regulations.
230/240V AC 50/60Hz mains supply to a suitable SELV
LED Driver.
Site conditions: LED equipment is more susceptible to
static damage and overvoltage than previous technology.
Before handling or connecting to the mains supply ensure
that all MSL products are protected from static discharge
and that the mains supply is to regulation. (230V +10
-6%)
Mains cables must be double insulated, strain relieved
and separated from E.L.V output cables.
This unit requires a constant current driver. 700mA Max.
Observe polarity:
Positive (+) is marked as RED.
Incorrect supply or reverse polarity can cause irreparable
damage.
All connections must be made before switching on mains.
If the supply is energised prior to making the connections
to the fitting then the resulting surge will damage the LED.
Multiple LEDs should be wired in series, refer to driver
instructions for minimum/maximum load.
All lighting equipment is delicate and easily damaged
through misuse or inappropriate installation (mechanical
or electrical). Repairs and replacements may cause
delays and will be chargeable. Contact MSL for support if
required. For full warranty terms & conditions please visit
our website.
The light source contained in this luminaire shall only be
replaced by the manufacturer or his service agent or a
similar qualified person.
Dimming control circuit source must be of SELV insulation
class.
Ensure supply driver and connectors are housed indoors
OR in a suitable IP rated enclosure
2
410 381 1497 inter-lux.com [email protected]
Inter-lux reserves the right to make technical changes without notice.
STOANE LIGHTING

12
33mm
or
Silicone
Install in well drained ground.
Surface gradient must run away from the
fitting.
To driver
IP66
Connector
Retaining Fin
3
410 381 1497 inter-lux.com [email protected]
Inter-lux reserves the right to make technical changes without notice.
STOANE LIGHTING

Old Optic
Replacement
Optic
OPTIC CHANGE
To change the optic;
Step 1 Unscrew the bezel
Step 2 Remove the optic from the black optic holder
Step 3 Place the new optic in the black optic holder
Step 4 Replace black optic holder in fitting, placing
the four legs of the optic holder into the
corresponding holes in the fitting, and fully
tighten bezel
1
2
3
4
4
410 381 1497 inter-lux.com [email protected]
Inter-lux reserves the right to make technical changes without notice.
STOANE LIGHTING