Lightolier RADIANCE PENDANT FIXTURES Guide

\
READAND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE INSTRUCTION SHEET NO.
‘hisfislure is intendedforinstallationinaccordanwwilhtheNationalElectricalCodeendlocalregulations.
oassurefullcompiianc$withlocalcadesandregulations,&e&with yourlocalelectricalinspectorbefore
!stallafion.To preventelectricalshock,turnoff electricityatfuse box before proceeding, IS:40712
Retainthese instructions for maintenancereference. 1292 Page1of 2
INSTRUCTIONS FOR INSTALLATION OF RADIANCE PENDANT FIXTURES
FIXTUREASSEMBLYANDINSTALLATION:
1. CarefullyremoveCENTERSTEMASSEMBLYfrompacking.
2. Gently pull downward on CANOPY to disengaga from CROSSBAR SPRING CLIPS and axpose CROSSBAR,
3. Mount CROSSBAR and CENTER STEM ASSEMBLY to OUTLET BOX using OUTLET BOX SCREWS (provided with oullet box).
4. Adjust SWIVEL CASTING. For sloped miting appfication$ loosen UPPER LCCK NUT and turn SWIVEL CASTING until “U-SHAPED” opening in SWIVEL
isparallel
to ceiling plane. This procedure can also be used treorientation of SWIVEL CASTING is desired on non-sloped ceifings.
NOTE Fixture should only be mounted to mihngs having amaximum slope of 45” or less,
5. Make electrica connections black fixture lead or fixture lead without tracer marks to (hot) black supply lead; white fixture lead or fixture lead with trao?r mark
to (neutral) white supply lead. Uninsulated (bare) fixture wire isagmund and must be connected toa grounding terminal orwirein OUTLET BOX. Use WIRENUTS
(local hardware item). If supply wires are located witfin three inches of ballast, use wire rated for at least 90° C,
6. SldeCANOPY UPCENTERSTEM ASSEMBLY andallowSWIVELCASTING topassthrough square opening inCANOPY. Push CANOPY upunti iffully engages
on CROSSBAR SPRING CLIPS and is sealed flush against ceiting,
7. Loosen and remove three BATTERY NUTS and STAR WASHERS from MOUNTING STUDS on LOWER FIXTURE ASSEMBLY,
8. Raise LOWER FIXTURE ASSEMBLY to MOUNTING
PLATE on CENTER STEM ASSEMBLY and make
electrica connections Snap togetherBLACK
CONNECTOR from LOWER FIXTURE ASSEMBLY tm
9.
9. I<> 9“17-<> 1.1 Em“ WRK’,!ww%ii%i

WTRlfCTfON SHEET NO.
S:40712 INSTRUCTIONS FOR INSTALLATION OF
RADIANCE PENDANT FIXTURES CONTINUED
!92 Page 2of 2
JSPENSION CABLE Attachment AND ADJUSTMENT
1. Loosen (do not remove) fhe BATTERY NUTS tha! secure WIREWAY COVERS on each of the three SUPPORT ARMS (Fig. 2 and 3A),
2, Slide each WIREWAY COVER inward towards the renter of the fixiure (Fig, 3A),
3. Position SUSPENSION CABLES through the SLOTS in the end of WIREWAYCOVERS(Fig,3B},
4. SifdeeachWIREWAYCOVERoutwardfromthecanterofthefixiure untilSUSPENSIONCABLEistau[,Securein position by tightening
BA~ERY NUTS (Fig. 3C).
5. Install recommended lamps by snapping base of lamp into SOCKET and allowing tip of lamp 10rest on LAMP SUPPORT BRACKET (Fig, 2),
IFFUSER CLEANING AND REMOVAL
CAUTION Turn power off to fixture before anempting to dean.
CMfusercan be cleaned from above the fixture by removing lamps and cleaning DIFFUSER with asoft damp cloth, Should DIFFUSERneedtobe
removedforcleaning,followstepsbelow,
1.
2.
3.
Removelampsfromfixlure,
Frombefowfixture,pushup on one side of the DIFFUSER and allow the opposite to drop down passed HOLOER KNOB (Fig. 1)
Side OIFFUSER out on an angle from LOWER FIXTURE ASSEMBLY
NOTEOIFFUSERmayhaveFObegentlycompressedoneitherside 10pass through opening in LOWER FIXTURE ASSEMBLY.
SUPPORTARM.-
WIREWAYCOVER
BA~ERY NUT
))
BATTERYNUT >
B
WIREWAYCOVER-J’ /d
SUPPORTARM FfG.3