Storehouse 93924 User manual

AUTO AND HOME KITAUTO AND HOME KIT
AUTO AND HOME KITAUTO AND HOME KIT
AUTO AND HOME KIT
ASSEMBLY AND OPERATING INSTRUCTIONS
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
Copyright © 2006 by Harbor Freight Tools®. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353
93924
Due to continuing improvements, actual product may
differ slightly from the product described herein.
- 208 Pieces -

SKU 93924 For technical questions, please call 1-800-444-3353 Page 2
Specifications
Item Description
Fuse Puller 4-1/8 (L) x ½ (H) x 3/8 (W) inches, orange
Test Leads Red and Black wire w/ alligator clips;
0.32 (L) x 0.093 (dia.) inch
Wire Stripper / Crimper
Tool
9 (L) inch bolt cutter: 8-3, 10-24, 10-32, 6-32,
4-40, and ignition; wire stripper: AWG: 10,
12, 14, 16, 18, 20, and 22.
Battery Terminal Brush 3.32 (L) x 1.52 (dia.) inch
Storage Case Folded: 10-1/4 (L) x 7 (H) x 3-1/4 (D) inches
Weight 2.7 lbs.
Save This Manual
You will need the manual for the safety warnings and precautions, assembly
instructions, operating and maintenance procedures, parts list and diagram. Keep
your invoice with this manual. Write the invoice number on the inside of the front
cover. Keep the manual and invoice in a safe and dry place for future reference.
Safety Warnings and Precautions
WARNING:When using tool,basic safety precautions should always be followed
to reduce the risk of personal injury and damage to equipment.
Read all instructions before using this tool!
1. Keep work area clean. Cluttered areas invite injuries.
2. Observe work area conditions. Do not use machines or power tools in damp
or wet locations. Don’t expose to rain. Keep work area well lighted. Do not use
electrically powered tools in the presence of flammable gases or liquids.
3. Keep children away. Children must never be allowed in the work area. Do not
let them handle machines, tools, or extension cords. This kit contains small
parts that can be choked upon or swallowed by children.
4. Store idle equipment. When not in use, tools must be stored in a dry location
to inhibit rust. Always lock up tools and keep out of reach of children.The small
parts within this kit can choke a child if put in their mouth.
5. Use the right tool for the job.Do not attempt to force a small tool or attachment
to do the work of a larger industrial tool.There are certain applications for which
this tool was designed. It will do the job better and more safely at the rate for
which it was intended. Do not modify this tool and do not use this tool for a
purpose for which it was not intended.
6. Use eye and ear protection. Always wear ANSI-approved impact safety goggles.
Wear a NIOSH-approved dust mask or respirator when working around metal,
wood, and chemical dusts and mists.

SKU 93924 For technical questions, please call 1-800-444-3353 Page 3
7. Dress properly. Do not wear loose clothing or jewelry as they can be caught in
moving parts. Protective, electrically non-conductive clothes and non-skid
footwear are recommended when working. Wear restrictive hair covering to
contain long hair. Never wear jewelry, watches, or other metal items while
working near a car’s battery; metal objects can cause the battery to short,
resulting in severe burns or causing the battery to explode.
8. Do not overreach. Keep proper footing and balance at all times. Do not reach
over or across running machines.
9. Maintain tools with care. Keep tools sharp and clean for better and safer
performance. Follow instructions for lubricating and changing accessories. Inspect
tool cords periodically and, if damaged, have them repaired by an authorized
technician.
10. Stay alert. Watch what you are doing, use common sense. Do not operate any
tool when you are tired.
11. Check for damaged parts. Before using any tool, any part that appears damaged
should be carefully checked to determine that it will operate properly and perform
its intended function. Check for alignment and binding of moving parts; any
broken parts or mounting fixtures; and any other condition that may affect proper
operation.Any part that is damaged should be properly repaired or replaced by
a qualified technician.
12. Guard against electric shock. Prevent body contact with grounded surfaces
such as pipes, radiators, ranges, and refrigerator enclosures. Do not work with
“live” wires. Disconnect power before making connections.
13. Replacement parts and accessories. When servicing, use only identical
replacement parts. Use of any other parts will void the warranty. Only use
accessories intended for use with this tool. Approved accessories are available
from Harbor Freight Tools.
14. Do not operate tool if under the influence of alcohol or drugs. Read warning
labels if taking prescription medicine to determine if your judgment or reflexes
are impaired while taking drugs. If there is any doubt, do not operate the tool.
15. Pacemaker safety warning. People with pacemakers should consult their
physician(s) before using this product. Electromagnetic fields in close proximity
to a heart pacemaker could cause interference to, or failure of the pacemaker.In
addition, people with pacemakers should adhere to the following:
Caution is necessary when near the coil, spark plug cables, or distributor of a
running engine.The engine should always be off if adjustments are to be made
to the distributor.
16. Avoid injury.While working around an engine that is running, keep hands and
arms away from all moving parts. Fast moving parts are hard to see.

SKU 93924 For technical questions, please call 1-800-444-3353 Page 4
Warning
A vehicle engine must never be started in a closed garage, or any other sealed
structure. Carbon monoxide is produced during operation and is deadly in a
closed environment. Early signs of carbon monoxide poisoning resemble the
flu, with headaches, dizziness, or nausea. If you have any of these signs get
fresh air immediately.
The warnings, cautions, and instructions discussed in this instruction manual
cannot cover all possible conditions and situations that may occur. It must be
understood by the operator that common sense and caution are factors which
cannot be built into this product, but must be supplied by the operator.
Unpacking
When unpacking, check to make sure that all the parts are included. Refer to the
Parts Photo and the Parts List at the end of this manual. If any parts are missing
or broken, please call Harbor Freight Tools at the number on the cover of this
manual.
Operation
Warning: Disconnect power before working on or near circuits.
1. Use the Crimping Tool (10) to cut and strip wire, and to crimp-tight Connectors
(18-31).
2. Use the Car Voltage Tester (14) by clipping its cable clip to the chassis, and
touch the other end to the test point. If voltage is present, the handle will light
up.
3. Disconnect the car’s battery following the manufacturer’s directions. Use the
assembled Battery Terminal Brush (13) to clean off post-type battery terminals.
Pull apart to expose a Brush to clean the inside of the cable connectors. Use
care when working near a battery: batteries contain acid which can cause
severe burns. Always wash hands thoroughly after working near a battery.
4. Remove and replace fuses using the Plastic Fuse Puller (5).
Maintenance
1. When finished using the Auto and Home Kit, replace all tools and store in a
clean and dry location.
2. Periodically check the kit supplies and replace as needed.

SKU 93924 For technical questions, please call 1-800-444-3353 Page 5
Parts List
metInoitpircseD.ytQmetInoitpircseD.ytQ
1"¼,temmorG671lacirtcelE,epaTllor1
2detrossA,spmalCelbaC3181,rotcennoCpaC )lio
chtiw,eulB( 5
3,otuA,sesuFdetrossA ni-gulP 591,rotcennoCpaC )lioctuohtiw,etihW( 5
4,otuA,sesuFdetrossA ssalG 502rotcennoCttuB )eguag61-22,deR( 01
5citsalP,relluPesuF112rotcennoCkroF )eguag61-22,deR( 01
6taeH,gnibuTdetrossA knirhS 0122rotcennoCgniR )eguag61-22,deR( 01
7mm001x5.2,eiTelbaC0332rotcennoCttuB )eguag41-61,eulB( 7
8mm061x5.2,
eiTelbaC0142rotcennoCgniRegraL )eguag41-61,eulB( 01
9mm002x6.3,eiTelbaC0152rotcennoCgniRllamS )eguag41-61,eulB
(01
01"¾,looTgnipmirC162rotcennoCkroF )eguag41-61,eulB( 51
112#spillihP,revirdwercS172tcennocsiDelameF )eguag41-
61,eulB( 5
21dradnatS,revirdwercS182tcennocsiDelaM )eguag41-61,eulB( 5
31lanimreTyrettaB,hsurB192rotcennoCttuB )e
guag01-21,wolleY( 5
41retseTegatloVraC103rotcennoCkroF )eguag01-21,wolleY( 4
51daeLtseTriap113rotcennoCgniRegraL )eguag01-21,wolleY( 4
61eriWlacirtcelE.tf523rotcennoCgniRllamS )eguag01-21,wolleY( 5
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN
THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR
DISTRIBUTOR MAKES ANY REPRESENTATION ORWARRANTY OF ANY KINDTOTHE BUYER
THAT HE OR SHE IS QUALIFIEDTO MAKE ANY REPAIRSTOTHE PRODUCT ORTHAT HE OR
SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE
MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATESTHAT ALL REPAIRS AND PARTS
REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSEDTECHNICIANS
AND NOT BY THE BUYER.THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF
HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTSTHERETO,
OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTSTHERETO.

SKU 93924 For technical questions, please call 1-800-444-3353 Page 6
Parts Photo
NOTE: Part locations may vary from those
shown above.
NOTE: Some parts are listed and shown for illustration
purposes only and are not available individually as
replacement parts.
(24)
(21) (25)
(30)
(31)
(27)
(26) (22)
(18,19)
(1) (2)
(20)
(29)
(23)
(6)
(16)
(7)
(8) (4)
(3)
(17)
(15)
(14)
(13)
(11)
(12)
(10)
(5)

SKU 93924 For technical questions, please call 1-800-444-3353 Page 7
WARRANTY CARD
3491 Mission Oaks Blvd. • P.O. Box 6009 • Camarillo, CA 93011 • [phone]
LIMITED 90 DAY WARRANTY
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and
durability standards, and warrants to the original purchaser that this product is free from defects in
materials and workmanship for the period of ninety days from the date of purchase. This warranty
does not apply to damage due directly or indirectly to misuse, abuse, negligence or accidents; repairs
or alterations outside our facilities; or to lack of maintenance. We shall in no event be liable for death,
injuries to persons or property, or for incidental, contingent, special or consequential damages
arising from the use of our product. Some states do not allow the exclusion or limitation of incidental
or consequential damages, so the above limitation of exclusion may not apply to you.
To take advantage of this warranty, the product or part must be returned to us with transportation
charges prepaid. Proof of purchase date and an explanation of the complaint must accompany the
merchandise. If our inspection verifies the defect, we will either repair or replace the product at our
election or we may elect to refund the purchase price if we cannot readily and quickly provide you
with a replacement. We will return repaired products at our expense, but if we determine there is no
defect, or that the defect resulted from causes not within the scope of our warranty, then you must
bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from
state to state.