jbc JT-D Series User manual

English
www.jbctools.com
Hot Air Station
Ref. JT-D
www.jbctools.com

FeaturesPacking List
The following items should be included:
JT Accessory set
Ref. 0012332
2 3
Manual .............1 unit
Ref. 0016475
* Not supplied with JT-Q stations
www.jbc tools.com
Power Cord .....1 unit
Ref. 0009417
(100V/120V)
0009401
(230V)
Hot Air Station
Ref. JT-D
Heater hose set ............1 unit
Ref. JT-T1A (100V / 120V)
JT-T2A (230V)
Stand ..................................1 unit
Ref. JT-SD
JTE Control Unit ............1 unit
Ref. JTE-1D
JTE-2D
JTE-9D
Extractor desk* ..............................................1 unit
Ref. 0008752
Suction Tube*
Ref. 0932330
Suction Cups*
Ref. 0930110
Ø 10 - 0934050 (x3)
Ø 4.7 - 0934070
Extractors*
Ref. E2184
E2064
E2052
Protectors*
Ref. P2220
P2230
P2235
P4000
P4010
Tripod*
Ref. T2050
T2250
Nozzles
Ref. JN2015
JN2012
JN2020
Another connectable tool:
Precision Heater hose set
Ref: TE-TB
Hot Air button
(On / Off)
Power Socket
Optional:
P-005 Pedal
connection
Fuse
Equipotential
connection
Heating
element
Suction Tube
Ref. 0932330
Heater Hose set
Ref. JT-T1A (100V/120V)
JT-T2A (230V)
Stand
Ref. JT-SD
For tripods
and extractors
Activates the
suction pump
USB-B connector
Update the station
software from
the JBC website
2
www.jbctools.com
3

Press Press
Do not
press
1. From the main Menu, select the mode to activate the tool depending on the task.
2. The tool stops blowing hot air when returned to the stand.
Stand + Autostart OFF Stand + Autostart ON Pedal*
Adjust the tool holder angle to suit your work position.
Press the start/stop button to
blow hot air.
The tool automatically starts
blowing hot air when lifted
from the stand.
Press the Pedal to blow hot
air and release to stop.
*The P-005 Pedal is not
supplied with this station.
See our website.
Quick Nozzle Changer
Changing nozzles quickly and safely.
Compatible Nozzles
The JT-TA works with JT nozzles. Find the model that best suits your soldering needs in www.jbctools.com
2
1
4 5
Adjustable Stand
Operation Modes
In case of a loosely fitting nozzle:
Ref. Shape Size
JN2020 Straight Ø 8mm
JN8417 Straight Ø 10mm
JN2015 Bent Ø 4mm
JN2012 Bent Ø 6mm
JN6633 Bent Ø 8mm
JN7637 Flat 10 x 2mm
JN7638 Flat 20 x 2mm
JN7639 Flat 30 x 2mm
Straight Bent Flat
Ø mm Ø mm A x B mm
1. Push the nozzle tab inwards with a
screwdriver or flat-nosed pliers.
2. Insert the nozzle into the JT-TA Heater again.
Turn the tool off
and handle with
care. The heating
element and the
nozzle are still hot.
4
www.jbctools.com
5

Temp º CAir %
Time to stop 45 seconds
Power 70%
400 85
400ºC Select
For small components (fig. 1 and 2). For large components (fig. 3 and 4).
Operation
Process Control
3. Releasing1. Placing 2. Heating
6 7
We recommend using the protector + tripod We recommend using the extractors
Protectors & Extractors
1 2 3 4
Protectors
* Ref. AxB (mm) * Ref. AxB (mm)
P3353 4,3 x 3 48 P2230 15 x 15
P3786 5,2 x 5,2 60 P4010 17 x 17
P3352 5,2 x 7,5 P4005 18 x 29
P3355 5,2 x 9,5 P4030 18,5 x 18,5
P3356 6,2 x 4,2 P1068 18,5 x 24
P3785 7,2 x 7,2 P2685 28,5 x 28,5
P3784 8,2 x 8,2 P4085 31,5 x 31,5
P4035 9 x 13 P2672 33 x 46
P4040 9,5 x 19 P4002 50 x 50
P4080 9,5 x 21 P3357 52,5 x 14
32 P2220 10 x 10
P4045 10,5 x 21
P4090 11 x 16
24 P2235 12 x 17
P1249 12 x 23
44 P4000 12,5 x 12,5
P3354 13,2 x 13,2
P4025 13,5 x 21,5
øD
* Reference Desk
Tripods
* Ref. øC (mm)
T2050 39
T2250 85
Manual extractor
* Ref. øD (mm)
E2190 7
Extractors
* Ref. AxB (mm) * Ref. AxB (mm)
52 E2052 20 X 20 E2124 45 X 45
64 E2064 20 X 26
80 E2184 24 X 24
E2068 27 X 27
E4020 28,5 X 28,5
E4015 31,5 X 31,5
E2084 33 X 33
E2100 38 X 38
Position the extractor with the
appropriate suction cup and
press the suction button.
Heat the component. The component lifts off
automatically when the
solder melts.
Access Menu (pess key 2 seconds) & Confirm Selection
Selected temperature
Current temperature
% Instant power supplied
to heater
You can switch between operating modes (Manual Mode / Program Mode) by pressing the
“increase” and “decrease” keys simultaneously for 2 seconds (Only when programs mode is ON).
Manual Mode
Current air flow
6
www.jbctools.com
7

Temp º C
º CProgram 8
380
Air 100%
Time 125s.
Main menu
1 Reset station
2 Station Settings
3 Program Settings
4 Counters
5 Program version
Exit
Station Settings Program Settings
Edit Program
Edit Program 1
1 Temp unit Celsius
2 Maximum temp 450
0
C
3Minimum temp T OFF
4 Fix temp -----
5 Temp Adjust + 0
0
C
6 Max air 100%
7 Min air 10%
8 Fix air -----
1 Programs OFF
2 Edit program
3
Copy program
4
Delete program
Back
Select
Program
Step 1
Time 30
Temp 300
Air 100
º C
º C
1
Exit
Counters
1 Station ON hours 0
2 Works hours 0
3Works cycles 0
Back
9 Time to stop 120 sec
10 Stand/Pedal Stand
Autostart OFF
11 Beep ON
12 Pop up ON
13 Change PIN
8 9
Decrease program
number
Increase program
number
Selected program
Current temperature
Selected air flow
Graph of selected
program
Remaining time
Program Mode
Program Options
Edit Program
This option allows you to edit or create a program.
First, you must select the program to edit and then modify the points that make up the program.
Each program is composed of 9 points, each point consisting of 3 parameters:
1. Time (seconds)
2. Temperature (°C / °F)
3. Flow rate (%)
You can delete the last point of the program by selecting “-----” in the time parameter.
It should be taken into account that the regulation range permitted by the station is 150-450°C, whe-
reby it is not possible to create temperature ramps between room temperature (Toff) and 150°C.
The station can store up to 25 temperature programs.
The first three programs are edited by JBC as an example.
Copy Program
This option allows you to copy a program.
You must select the program source and its destination (where it will be copied).
Delete Program
This option will allow you to delete a previously selected program.
* Selecting Minimum Temp as
“T OFF”, the air blows at room
temperature.
Menu Screen
Original PIN: 0105
8
www.jbctools.com
9

Choose the needle and the suction cup that best fits the component and start working as follows:
Maximum working temp: 250ºC (482ºF)
Operation
1. Suction
Pick & Place
Ref. T260-A
2. Release
This tool helps you easily place and remove SMDs of any size thanks to the suction pump.
Pick & Place (not supplied with JT)
Press the button to
start/stop the suction
Once the suction is
activated, cover the
pen hole with your
finger and lift off the
component.
Insert the needle
with the appropriate
cup for a correct
suction process.
Lift your finger
to release the
component in the
appropriate place.
You should
avoid the needle
protruding from the
lower part.
Pick & Place
Ref. T260-A
Straight Needles Set
Ref. 0901546
Bent Needles Set
Ref. 0861660
10 11
Only perform this operation when the element is cold and the unit is disconnected from the mains.
1. Loosen the screw.
2. Pull the heating element away from the handle.
3. Connect the new heating element, ensuring its pushed all the way in.
4. Tighten the screw.
Replacing the Heating Element
Heating Hose Set
Ref. JT-T1A (100V / 120V)
JT-T2A (230V)
Heating Element
Ref. 0014107 (230V)
0014105 (100V / 120V)
Handle
Ref. 0009829
1. Ensure that the tool is turned off.
2. Use a spanner to unscrew the connecting nut.
3. The tube end of the new heater must be inserted
so that the longitudinal rib fits into the groove.
5. Follow the same steps conversely.
Changing the JT-TA Heater Hose Set
10
www.jbctools.com
11

1. Pull off the fuse holder and remove the
fuse. If necessary use a tool to lever it off.
2. Press the new fuse into the fuse holder
and replace it in the station.
Fuse holder
Fuse holder
Fuse
Safety
- Do not use the units for any purpose other than soldering or rework. Incorrect use may cause fire.
- The power cord must be plugged into approved bases. Be sure that it is properly grounded
before use. When unplugging it, hold the plug, not the wire.
- Do not work on electrically live parts.
- The tool should be placed in the stand when not in use in order to stop blowing hot air The nozzle,
the heating element and the metal part of the stand may still be hot even when the station is turned
off. Handle with care, including when adjusting the stand position or changing nozzles.
- Do not leave the appliance unattended when it is on.
- Do not cover the ventilation grills. Heat can cause inflamable products to ignite.
- Use a “non residue” classified flux and avoid contact with skin or eyes to prevent irritation.
- Be careful with the fumes produced when soldering.
- Keep your workplace clean and tidy. Wear appropriate protective glasses and gloves when
working to avoid personal harm.
- Utmost care must be taken with liquid tin waste which can cause burns.
- This appliance can be used by children over the age of eight and also persons with reduced
physical, sensory or mental capabilities or lack of experience provided that they have been given
adequate supervision or instruction concerning use of the appliance and understand the hazards
involved. Children must not play with the appliance.
- Maintenance must not be carried out by children unless supervised.
It is imperative to follow safety guidelines to prevent electric
shock, injury, fire or explosion.
12 13
Maintenance
- Clean the station screen with a glass
cleaner or a damp cloth.
- Use a damp cloth to clean the casing and
the tool. Alcohol can only be used to clean
the metal parts.
- Maintain heating element clean prior to
storage in order to avoid its oxidation.
Rusty and dirty surfaces reduce heat
transfer.
- Periodically check all cables and tubes.
- Replace a blown fuse as follows:
- Replace any defective or damaged pieces. Use original JBC spare parts only.
- Repairs should only be performed by a JBC authorized technical service.
Before carrying out maintenance or storage, always allow the equipment to cool.
Clean periodically
12
www.jbctools.com
13

14 15
Exploded View
JT-1D 120V 50/60Hz. Input fuse 8A. Rated current: 6A. Control Unit model: JTE-1D
JT-2D 230V 50/60Hz. Input fuse 4A. Rated current: 3A. Control Unit model: JTE-2D
JT-9D 100V 50/60Hz. Input fuse 8A. Rated current: 7A. Control Unit model: JTE-9D
- Weight: 6.7 Kg (14.7lb)
- Dimensions: 148 x 184 x 140
- Nominal Power: 700W
- Temperature selection: Room temperature / 150ºC to 450°C (300ºF to 840ºF)
Cool mode: T Off. Used to blow air at room temperature
- Ambient Operating Temperature: 10 to 40ºC (50-104ºF)
- Air flow regulation: 10-50 SLPM
- Vacuum: 30% / 228 mmHg / 9 inHg
- USB connector station-PC
- P-005 Pedal Connection
Complies with CE standards
ESD protected housing “skin effect”
Specifications
14
www.jbctools.com
15

0016475-0615
www.jbctools.com
Warranty
JBC’s 2 year warranty covers this equipment
against all manufacturing defects, including the
replacement of defective parts and labour.
Warranty does not cover product wear due to use
or mis-use.
In order for the warranty to be valid, equipment
must be returned, postage paid, to the dealer
where it was purchased.
This product should not be thrown in the garbage.
In accordance with the European directive 2002/96/EC, electronic equipment at the end of their life
must be collected and returned to an authorized recycling facility.