Strand Lighting 100 User manual

100 Console
Operations Manual
Manual
Part No. 24-004-0816

Page 2 Strand 100 Console Manual
Welcome
Thank you for buying Strand Lighting control equipment. We hope
that you will find that your lighting needs are met by your new
system and that you will enjoy exploring the new facilities that your
new system offers. You are provided with essential information to
help you install and operate your system. Please look through all
the documents and keep them safely for future use. If you have
any difficulties, please do not hesitate to contact Strand Lighting or
any authorized Strand service center for advice.
This equipment is designed to operate from the mains electrical
supply and contains voltages, which, if touched, may cause death
or injury. It should only be operated in accordance with the
instructions provided and for the purpose of a lighting control
system.
Do not open the console. There are no user serviceable parts
inside.
Avoid spilling liquid on the equipment If this should happen, switch
the equipment off immediately at the mains. To reduce the risk of
fire or electric shock, do not expose the equipment to rain or
moisture.
For indoor use only.
This equipment is designed and manufactured to comply with
international safety standards 1EC950, UL1950, CS950 and is
intended for use as part of a lighting control system. It must not be
used for other purposes where there is a risk of safety to persons.
The equipment contains power voltages, socket outlets shall be
installed near to the equipment and be easily accessible.
• Working Voltage/Current 100-120 (2A) 220-240 (1A)
• Frequency 50/60 Hz
• Max Ambient Temp 350C
• Do not restrict ventilation
This manual describes the installation and operational procedures
for Strand Lighting’s 100 Control Console.

Strand 100 Console Manual Page 3
Offices and Service Centers
Phone numbers do not include country code or other international access data.
World Wide Web: http://www.strandlighting.com/
Berlin
Strand Lighting GMBH
Ullsteinstrasse. 114-142, HAUS C
D-12109
Berlin, Germany
Tel. [phone] Fax [phone]
Hong Kong
Strand Lighting Asia LTD
20/F., Delta House
3 On Yiu Street
Shatin, N.T.
Hong Kong
Tel. [phone] Fax [phone]
London
Strand Lighting Limited
Unit 3 Hammersmith Studios
Yeldham Road
Hammersmith
London, England W6 8JF
Tel. [phone] Fax [phone]
Los Angeles
Strand Lighting Inc
6603 Darin Way
Cypress, CA 90630
U.S.A.
Tel. [phone] Fax [phone]
Moscow
Strand Lighting
Novinsky Boulevard 20A Building 3-6
12069 Moscow, Russia
Tel. [phone] Fax. [phone]
Rome
Strand Lighting Italia
Via Delle Gardenie S.N.C.
Pontina Vecchia KM 33,400
00040 Pomezia, Italy
Tel. [phone] Fax [phone]
Toronto
Strand Lighting (Canada) Inc
2430 Lucknow Drive #15,
Mississauga, Ontario, L5S 1V3
Canada
Tel. [phone] Fax. [phone]

Page 4 Strand 100 Console Manual
Table of Contents
Welcome....................................................................................................................2
Offices and Service Centers.......................................................................................3
Table of Contents.......................................................................................................4
Getting Started...........................................................................................................5
Concept..................................................................................................................5
Ordering Information...............................................................................................5
Mechanical & Environmental Data..........................................................................5
Standards Compliance ...........................................................................................5
Unpack the Console ...............................................................................................5
Face Plate ..............................................................................................................6
Back Plate ..............................................................................................................6
Connect Power.......................................................................................................7
Connect DMX .........................................................................................................7
Rack Mounting........................................................................................................8
Turning the Console On.......................................................................................... 8
Layout ........................................................................................................................9
Quick Guide .............................................................................................................10
Operation .................................................................................................................12
Two Scene Operation...........................................................................................12
Manual Crossfades...............................................................................................12
Timed Crossfades.................................................................................................12
Single Scene Operation........................................................................................13
Hold......................................................................................................................14
Effect – Single Scene Mode .................................................................................15
Effect – Two Scene Mode.....................................................................................16
Conclusion ...............................................................................................................16
Appendix A...............................................................................................................17
Control Input.........................................................................................................17
Index ........................................................................................................................18

Strand 100 Console Manual Page 5
Getting Started
Concept
The Strand 100 series console is a small, simple to use, preset lighting
desk. It can either control 24 channels in 1 scene or 12 channels in 2
scenes with the ability to expand scenes with the Hold feature. The
console also has the ability to run a single effect. This console can be
rack mounted.
Ordering Information
Catalog # 61312 – 100 series 12/24 console 120 volt
Catalog # 61313 – 100 series 12/24 console 230/240 volt
Catalog # 24-004-0816 - 100 series manual
Mechanical & Environmental Data
Weight: 2kg/4.5lb
Finish: Blue powder coat epoxy paint
Construction: Rigid folded sheet steel
Temperature: 0 – 35°C
Humidity Range: 0-90% non-condensing
Ingress Protection: IP20
Standards Compliance
All units are CE marked. 120 volt consoles include UL, cUL power
supplies.
Unpack the Console
Unpack the console from the packaging and check that the following
components are contained within. If any parts are missing, or damaged,
please contact the carrier and your nearest Strand Lighting office.
List of Parts for North America…
100 series console
Power cable with UL power supply cable with US 2 pin connector.
Manual
List of Parts for Europe and Asia…
100 series console
Power cable with cUL power supply cable with
UK 2 pin connector and EU 2 pin connector
Manual

Page 6 Strand 100 Console Manual
Face Plate
100
Back Plate

Strand 100 Console Manual Page 7
Connect Power
Connect the appropriate power cable to the power
adapter and into the console. Connect the male
end to the electrical service.
Connect DMX
Connect the DMX cable from the dimmer rack
input to the DMX output of the console.
(See Appendix A for complete DMX512
connector information.)

Page 8 Strand 100 Console Manual
Rack Mounting
Below is a drawing that illustrates the removal of the edge pieces for rack mounting.
Turning the Console On
Switch the rocker switch to the ON position.

Strand 100 Console Manual Page 9
Layout
100
GRANDMAS TER
FLASHMODE BUTTON
SCENE MASTER(B)/EFFECTMASTER
SCENE MASTER(A)
HOLDBUTTON
SCENE MODE BUTTON
EFFECTFORWARD
EFFECTREVERSE
EFFECTBOUNCE
EFFECTRANDOM
BLACK OUT BUTTON
LEDDISPLAY
FADE TIME /FXSPEEDROTARY
CHANNEL FADER
FADERFLASHBUTTON
LED

Page 10 Strand 100 Console Manual
Quick Guide
Grand Master – an inhibitive fader that proportionately controls all other faders.
This determines maximum output of all faders at all times. The grand master is
always active.
Playback A – an inhibitive fader that proportionately controls all faders for the A
scene.
Playback B / Effect Master – when not running the effect, an inhibitive fader that
proportionately controls all faders for the B scene. When running the effect, the
fader is a inhibitive master for the effect.
Channel Faders – a fader that controls the output of the corresponding dimmer
number.
Fader Flash Buttons – a momentary button that flashes the level of the
corresponding fader to full. Which fader is corresponding depends on the setting of
the FLASH BUTTON. See below.
Mode Button – toggles between the two modes of operation of the console. 1
scene 24 channel mode or 2 scene 12 channel mode. The default is two scene
mode.
Hold Button – this button will freeze the output of the faders so that the operator can
reset the channel faders for a different look. This is only available in single scene
mode.
Flash Button Mode Button – there are only 12 fader flash buttons and this button
toggles the fader flash buttons between OFF, faders 1 – 12 and faders 13 – 24.
Fade Time / Effect Speed Dial – when not running the effect, this will allow the
operator to set the fade time of the scene masters. When running the effect, this will
allow the operator to set the rate at which the effect is running. See the LED display
for time / speed readout.

Strand 100 Console Manual Page 11
Effect Options Buttons – these will allow the operator to change the stepping
options of the effect.
Forward – this will allow the faders that have a level to step through their
appropriate levels from the lowest number fader number to the highest.
Reverse – this will allow the faders that have a level to step through their
appropriate levels from the highest number fader number to the lowest.
Random - this will allow the faders that have a level to step through their
appropriate levels in a randomly generated order.
Bounce - this will allow the faders that have a level to step through their
appropriate levels from the lowest number fader number to the highest then
back to the lowest number fader.
LED Display – this will show alpha / numeric information about the console. Such
as fade time, effect step rate and whether the black out button is active.
LED Lights – all channel faders have LEDs that mimic the output level of each
fader. LEDs also are indicators of the channel mode as well as when all features are
activated. All LEDs are green.
Black Out Button – this will allow the operator to instantly stop all fader output.
Press again to restore fader output.

Page 12 Strand 100 Console Manual
Operation
Two Scene Operation
The first time you power up the console, it will default to two
scene mode. The corresponding light will confirm that the
console is in two scene mode.
Now playback A will be the scene master for the top bank of
channel faders and playback B will be the scene master for
the bottom bank of channel faders. These two banks of
faders both correspond to dimmers 1 – 12.
Manual Crossfades
Playback A is at full when the fader is in the UP position and at 0 when the fader is in
the DOWN position. Playback B is just the opposite of playback A. (Refer to the
vertical numbering beside the playbacks). This allows for proportional crossfades by
moving both faders simultaneously in the same direction.
Individual channel fader control works the same in two scene mode as it does in one
scene mode.
Timed Crossfades
For timed crossfades – use the same procedure as the manual
crossfade but with the fade timer set to the preferred fade time.
The LED display will show the fade time that is set. Timed
crossfades can vary from 0 (Manual) to 15 minutes.

Strand 100 Console Manual Page 13
Single Scene Operation
Make sure the channel mode button has the console in the
single scene mode. Change the mode by pressing the channel
mode button. (The corresponding light will be on)
Make sure the grand master is at full or at the desired level.
Make sure the playback A master is at full or at the desired level.
Once the above are set, simply set the faders (1 – 24)
to the appropriate levels. At this point, the dimmers
should correspond to the level of the faders. The fader
output of the fader that is being adjusted will be shown
in the LED display on a scale from 0 to 100.
Refer to the HOLD section for crossfade information.

Page 14 Strand 100 Console Manual
Hold
In single scene mode only, using hold allows the operator to
freeze all dimmer output and manually reset the levels for all 24
faders to create a different look on stage. Here’s how it works…
Select current settings with channel faders. Make sure playback A master is at 10
and playback B master is at 0. (That’s both playbacks in the UP position). The hold
feature can only be activated and deactivated with playbacks in these positions.
Press the hold key (The hold LED will now be on), move playback A’s master to 0
while moving playback B’s master to 10. During the crossfade, the hold LED will be
flashing.
The current fader settings will now be recorded into hold’s memory. (The hold LED
will stop flashing but remain on indicating the activation of the hold feature. The
operator is now free to reset all channel faders to the levels for the next cue. Once
the channel faders are set, crossfade playback A’s master back to 10 and playback
B’s master back to 0. (During crossfade the hold LED will flash) After a crossfade is
completed, the second cue will now be outputting live. (The hold LED should still be
on) Repeat the above step for the next crossfade or press hold again to release the
hold function. After pressing hold, the hold LED should turn off.
Also note, that playback B is now the master for the held scene. So if playback B is
moved to 0 (UP) then the held state fades out.
For timed crossfades – use the same procedure as the manual
crossfade but with the fade timer set to the preferred fade time.
The LED display will show the fade time that is set.
Remember: Hold can only be accomplished with both
faders in this position.

Strand 100 Console Manual Page 15
Effect – Single Scene Mode
An effect is a way to get fast changing output of dimmer levels in
a specific order. The effect capability of this console is limited
but simple to do. The console can run one effect.
Set the console to single scene mode. Set playback A to 0
(Down) and playback B to 0 (Up). Playback B will become the
effect master. (See the colored information beside the Playback
B). Set current fader levels to include only the faders that will be
in the effect. Set them to any level from 1 to 100.
Press one of the effect buttons (Forward, Reverse, Random,
Bounce).
Forward will allow the active faders to chase in
order from the lowest number to the highest
number. (1 – 24).
Reverse will allow the active faders to chase in
order from the highest number to the lowest
number (24 – 1)
Random will allow the active faders to chase in a randomly generated order.
Bounce will allow the active faders to chase, first, in order from the lowest number to
the highest and then, from the highest number to the lowest.
The lights will now be chasing in one of the 4 directional modes. The effect master
will inhibit the levels of all effect channels. The fade time rotary becomes the
SPEED dial. Set the speed of the effect appropriately. Check the LED display for
your rate.
The effect can be faded in rather than the effect starting abruptly by pulling down the
effect Master and fading it up at the appropriate time.

Page 16 Strand 100 Console Manual
Effect – Two Scene Mode
To run the effect in two scene mode, just switch the channel mode to two scene.
(Check the LED for indication of the appropriate mode setting). Now all of the fader
levels from the bottom fader bank will become the faders in the effect. With both
playbacks in the up position, just press any of the effect directional keys and the
effect will start immediately.
Once the effect is running, adding new fader levels will add those faders into the
effect.
Conclusion
This concludes the instructional manual for Strand’s 100 series console.

Strand 100 Console Manual Page 17
Appendix A
Control Input
The DMX512 input will accept a multiplexed digital control signal which conforms to
USITT specification DMX512 (1990). Details of this specification are available from
USITT on request.
The control input is via a five-pin male XLR type connector. Pin connections are
shown in Figure 9. A five-pin female XLR connector is also fitted to allow a series of
SD 6 packs (or other DMX equipment) to be connected together in ‘daisy chain’
fashion.
It is recommended that Control connections are not plugged or unplugged when power is applied to
the dimmer pack as this may cause any connected loads to flash up momentarily.

Page 18 Strand 100 Console Manual
Index
B
Back Plate .................................................6
Black Out Button
Quick Guide........................................11
Bounce ....................................................15
Quick Guide See Effect Options Buttons
C
Channel Faders
Quick Guide........................................10
Conclusion ..............................................16
Connect DMX...........................................7
Connect Power..........................................7
Control Input...........................................17
D
DMX output..............................................7
DMX512.................................................17
E
Effect – Single Scene Mode....................15
Effect – Two Scene Mode.......................16
Effect Options Buttons
Quick Guide........................................11
F
Face Plate..................................................6
Fade Time / Effect Speed Dial
Quick Guide........................................10
Fader Flash Buttons
Quick Guide........................................10
Flash Button Mode Button
Quick Guide........................................10
Forward...................................................15
Quick Guide See Effect Options Buttons
G
Getting Started..........................................5
Grand Master
Quick Guide........................................10
H
Hold ........................................................14
Hold Button
Quick Guide........................................10
L
Layout.......................................................9
LED Display
Quick Guide........................................11
LED Lights
Quick Guide........................................11
M
Manual Crossfades .................................12
Mode Button
Quick Guide........................................10
O
Operation ................................................12
P
Playback A
Quick Guide........................................10
Playback B / Effect Master
Quick Guide........................................10
Q
Quick Guide............................................10

Strand 100 Console Manual Page 19
R
Rack Mounting..........................................8
Random...................................................15
Quick Guide See Effect Options Buttons
Reverse....................................................15
Quick Guide See Effect Options Buttons
S
Single Scene Operation...........................13
T
Timed Crossfades ...................................12
Turning the Console On ...........................8
Two Scene Operation .............................12