Strand Lighting Wallrack User manual

Armoire Gradateurs Wallrack
Manuel d'utilisation
Distribué par PANADIFFUSION 84000 AVIGNON tél : [phone]
Revision Level 2.2
Revision Date Rev Février 2010

Informations Générales
This equipment operates at voltage levels that are potentially lethal. Do not
touch any of the internal parts of the equipment unless you are fully aware
of the hazards involved and the precautions to be taken.
It is imperative to provide an adequate earth conductor for the rack and
load connections. Do not rely on earthing via conduit or trunking.
The equipment described in this manual is designed and manufactured to comply
with international safety standards IEC 950 and is intended for use as part of a
lighting control system. It must not be used for other purposes where there is any
risk of safety to persons. It is important that installation be carried out in
accordance with the instructions given in this manual and in compliance with
applicable electrical regulations. The work should be carried out by a suitably
qualified electrician.
The system is designed to be permanently installed with supply and load wiring
permanently connected.
In the interests of continued safe and reliable operation, observe the following
guidelines:
xKeep the equipment at a room temperature of 0-35qC and a relative humidity
of 10-95% (non-condensing) during operation. For operation between 35qC and
40qC de-rate the maximum load by 4% per qC.
Do not, under any circumstances, operate the equipment above 40qC or in an
environment that may become wet.
xAvoid sudden extremes of temperature, rain, direct sunlight, or other heat
sources.
xMake sure that wires and cables are routed sensibly and wired in
accordance with local regulations.
xDO NOT drop the equipment or subject it to excessive bumping or jarring.
xDO protect the unit from excessive dust or other contamination.

Wallrack Notice d'emploie
Table des Matières
Installation............................................................................................ 5
Location ................................................................................ 5
Ventilation ............................................................................. 5
Weight................................................................................... 5
Dimensions ........................................................................... 5
Installation Procedure ........................................................... 7
Supply Connections .............................................................. 7
Three Phase ..................................................................... 7
Single Phase..................................................................... 8
Load Connections ................................................................. 8
RCD Option......................................................................... 10
Control Signal Connections................................................. 12
Processor set up................................................................................ 13
Main Menu .......................................................................... 13
Set Level ............................................................................. 14
Preset.................................................................................. 15
Address............................................................................... 16
Curve .................................................................................. 17
Set minimum level............................................................... 18
Set maximum level.............................................................. 19
Set up menu........................................................................ 20
Response Time............................................................... 20
DMX Port ........................................................................ 21
DMX Fail ......................................................................... 22
Set Signal Call ................................................................ 23
Version Number.............................................................. 23
Set Factory Defaults ....................................................... 23
Triac Replacement ............................................................................. 24
User Manual v2.2 Jan. 20074

Wallrack User Manual
User Manual v2.2 Fev.2010 5
Installation
Dimmer systems contain potentially hazardous voltages and high temperatures.
Installation should only be carried out by suitably qualified personnel, safe working
practices observed, and caution exercised at all times. Ensure that all Power supplies
are properly isolated before gaining access.
Location Any dimmer installation requires careful choice of location. Dimmers
should, if possible, be sited close to the lamp loads to minimise cable
runs. Although the design of Wallrack reduces the radiated noise
common to conventional dimmers, it is important to avoid siting in
acoustically 'live' positions in the performance area.
The incoming mains distribution should be sited as close to the racks as
practicable, and adequately fused isolators provided close to each rack.
Max rating 80A-3 phase, 160A-single phase(Wallrack 24x2.5kW).
Allow adequate clearance at the front of the dimmer rack, in order for it to
be opened for wiring to the load, supply and control terminals and allow
safe servicing of the equipment.
Ventilation
Adequate ventilation must be provided to maintain an ambient
temperature within the range 0 to 35 C and humidity of 45-95% non-
condensing. Special attention should be paid to the need to maintain
ambient temperature within these limits when Wallrack is enclosed in a
small room.
Do not obstruct the ventilation slots.
Weight
Wallrack:
Wallrack, packed:
24 x 2.5kW
43kg
49kg
6 x 5kW
31.4kg
34.5kg
Wallrack dimmers are heavy, take care when lifting.
Dimensions
Cable entry dimensions are as follows:
Power Wiring Top 4 x 25mm holes suitable for conduit(4x2.5kW Wallrack) .
Control Wiring Bottom 4 x 25mm holes suitable for conduit(4x2.5kW Wallrack) .
Max rating 50A-3 phase, 150A-single phase(Wallrack 6x5kW ).
Max rating 20A-3 phase, 60A-single phase(Wallrack 6x2.5kW ).
6 x 2.5kW
15.6kg
18kg
Top 3 x 25mm holes suitable for conduit(6x5kW Wallrack) .
Top 2 x 25mm holes suitable for conduit(6x2.5kW Wallrack).
Bottom 3 x 25mm holes suitable for conduit(6x5kW Wallrack) .
Bottom 2 x 25mm holes suitable for conduit(6x2.5kW Wallrack) .

Wallrack User Manual
Wallrack 24x3kw
Wallrack 6x5kw
User Manual v2.2 Fev. 2010 6
Wallrack 6x3kw