Strategic Scents Showroom User manual

Strategic Scents
Strategic Scents
Strategic Scents
Strategic Scents
Showroom
Diffuser manual and setup guide

Introduction
Please read these instructions carefully before use.
For further information please contact [e-mail]
Warnings
• Do not disassemble this device.
• Do not tilt this machine while in use, or when it contains scent oil.
• Only use the provided power supply. Any other power supply could cause damage to the machine
• Do not use in environments above 45 degrees celcius or 95% humidity
• Please keep out of reach of children
• Only add scent oil directly into the bottle using the instruction further in this manual. pouring oil into the
diffuser hose will cause damage.
• When refilling the scenting oil, please check the condition of the bottle o ring and replace if damaged
• When the machine will be out of service for a long period. Please remove the scenting oil and unplug
from the power supply
• Please install the maching with the weigh of the machine in mind. Do not install into drywall without
attaching to a wall stud.
Diffuser Overview
Locking key
Mounting bracket
Supply hose
Power inlet
Diffusion indicator
Power switch
Cooling Fan
Power supply
Atomizing head assembly
Current time
Cooling fan indicator
Day indicator
Diffuser strength (gearing)

Installation
First. locate a mounting point that is close to a power outlet and close enough to the HVAC air duct you wish
to plumb into that the supplied hose will reach. The machine MUST be plumbed into the HVAC air duct AFTER
the fan unit. And remember that the diffused scent will travel with the air. So if you are scenting an entire
area with multiple air outlets, make sure you are upstream from all the outlets. If you just want to scent one
area and exclude others (such as a single retail space within a mall), be upstream of the area you wish to
scent, and downstream from the ones excluded.
To mount the Showroom diffuser to a wall, please use the wall mount supplied.
Affix the wall mount to a supporting beam or wall stud to prevent mounting failure
making sure that the unit is close enough to the HVAC air duct that the supllied hose can
reach. Then align holes on the rear of the machine to the mounting points on the bracket.
Once the mounting is complete, screw the brass hose fitting into the machine.
Next, fill the bottle with the Strategic Scent of your choice To
access the scent bottle, simply insert the key and turn slightly
10 degrees clockwise. then lift the atomizing head and bottle
from the machine. Unscrew the bottle from the head to fill. To
reinstall the bottle, just follow those instructions in reverse..
Finally, Connect the hose to the machine. And to the HVAC air duct by drilling a XXmm
hole in the centre of the duct. Ensuring that your hole is downstream from the fan
assembly. Then install the supplied rubber grommet and push the end of the hose
through into the ducting by ~ 1” (20mm).
Now you’re ready to plug the machine into the power socket, turn on with the power switch and set up your
scenting program!
Please Note: when changing the strength of the scenting, remember less is more. Start off very light (scenting level
2-5) and adjust from there. The scent should be very subtle. If you think the scent may be too light, remove yourself
from the scented area for around 15 minutes, then re-enter. This will give a clearer indication of scent levels.

Machine programming
Power On
Once connected to power supply, there will be a short “beep” and the screen displays time and atomization strength.
Lock & Unlock
The machine will be locked automatically if there is no operation in 30 seconds, touch and hold SET button for 5
seconds to unlock the display.
Initial Day & Time Setting
Touch and hold SET button for 5 seconds till ‘beep’ sound, touch to choose the day, touch to move to time
setting, touch to adjust the value, touch to move to next setting number. Touch ENT to confirm.
Reset
Touch and hold ENT button for 5 seconds till ‘beep’ sound coming out to reset the default setting
(local day: Friday , local time: 12:00; Working day: Every day, Working period 1: 00:00 – 23:59)
Diffusion Schedule Setting
(1) Touch SET button to set working time period (such as 9am - 5pm), there are a possible 12 working periods in total
but most users just use 1. Choose one working period, touch to move to the setting number, touch to adjust
the time, (the start time cannot be greater than the end time, otherwise the setting will fail)
(2)Press the SET key again to enter the Days of operation Setting, touch the key to move the cursor to the
weekday to be set Touch the key to set whether to work on the day (ON /OFF)
(3)Then touch SET to enter the Atomizer Strength Setting, keys adjust the strength setting , then touch the
SET key to enter next timer, refer to the steps (1) This machine can set 12 working time periods).
Please Note: when changing the strength of the scenting, remember less is more. Start off very light (scenting level
2-5) and adjust from there. The scent should be very subtle. If you think the scent may be too light, remove yourself
from the scented area for around 15 minutes, then re-enter. This will give a clearer indication of scent levels.
After adjusting the appropriate parameters, touch the ENT key to save
Troubleshooting
Problem Solution
No Atomization Ensure power is connected, Air pump is functioning and schedule is set
through the app
Atomization level low Check the delivery hose is not blocked or kinked. Check scent cencentration
level through the app
Oil leak Check O ring around bottle
Machine excessively noisy Check for air leaks
Atomizer spraying liquid Atomizer head may be blocked. perform a cleaning