Street Furniture Classic Galleria Seat CMG1 User manual

MDP-07
streetfurniture.com
Version 2 @25.06.21
classic galleria
classic promenade
concourse
mall
installation guide
No. Product MCODE
1. Classic Galleria Seat CMG1
2. Classic Galleria DDA Seat CMG5
3. Classic Galleria Bench CMG4
4. Classic Galleria Mitred Slim Bench CMG8-M
5. Classic Galleria Slim Bench CMG8
6. Classic Galleria Table CMG6
7. Classic Galleria DDA Table CMG6-DDA
8. Classic Promenade Seat CMR1
9. Concourse Seat CML7
10. Mall Seat CMM1
No. Product MCODE
11. Mall DDA Seat CMM7
12. Mall Sun Lounge CMM-S
13. Mall Bench CMM4
14. Mall Curved Slim Bench CMM8-C
15. Mall Mitred Slim Bench CMM8-M
16. Mall Slim Bench CMM8
17. Mall Platform CMM9
18. Mall Table CMM6
19. Mall DDA Table CMM6-DDA
This guide relates to:

© Street Furniture Australia Pty Limited ABN 46 070 910 100
Version 2 @ 25.06.21 MDP-07 streetfurniture.com
Australia 1800 027 799
United States [phone]
International [phone]
Email [email protected]
N6 391 Park Road, Regents Park
NSW 2143, Australia
Welcome and congratulations on your purchase
from Street Furniture Australia.
This guide refers to seating and table products: Classic Galleria, Classic
Promenade, Concourse, and Mall.
Before beginning installation please read through this guide thoroughly.
Important to note:
• Handle the seat(s) and/or table(s) and parts in a manner to prevent
scratching, warping, bending and twisting. Do not slide parts on
concrete or other hard or abrasive surfaces.
• Please check that you have received all the components and inspect
goods on delivery. Double check with the list on the next page. The
image is for example only, you should receive your selected legs
and/or arms. Claims for defects or damage, shortage in quantity or
failure to comply with the description or quote must be made within
seven (7) business days. In case of damage, Street Furniture Australia
requires photographic evidence. If the damage occurred during
transport, we highly recommend taking photos prior to removing
packaging.
• There are several steps on this installation guide that may or may not
be applicable to your purchase.
Understanding Your Range
The Classic Galleria, Promenade, Mall and Concourse range offers several different leg and arm options that
may require assembly on site.
Leg options include:
Arm options include:
01 Splay
06 Tee
Not applicable for Classic
Promenade
09 Tee Narrow
Not applicable for Classic
Promenade
10 Wall Narrow
Only for Slim Benches
03 Splay Narrow
Only for Slim Benches
Angle Arm
Only for Classic Galleria
and Mall seats
02 Arch
07 Wall
04 Pedestal
11 Plinth
05 Post

© Street Furniture Australia Pty Limited ABN 46 070 910 100
Version 2 @ 25.06.21 MDP-07 streetfurniture.com
Australia 1800 027 799
United States [phone]
International [phone]
Email [email protected]
N6 391 Park Road, Regents Park
NSW 2143, Australia
This technical pack is copyright and owned by Street Furniture Australia Pty Limited ACN 070 910 100.
You may download and use this technical pack in unaltered form only for installing and maintaining our
products. All rights are reserved. Any use of our technical pack for purposes other than for the above-
mentioned purpose, is strictly prohibited without the prior written permission of Street Furniture Australia
Pty Limited, Level 1, 52-58 William Street, East Sydney NSW 2011. Street Furniture Australia Pty Limited
reserves the right to make modications to product specications without prior notice.
© Street Furniture Australia Pty Limited 2013. All rights reserved.
1800 027 799 streetfurniture.com
PAGE
leg assembly guide
SEATING, BENCHES AND TABLES
02
Thank you for purchasing a Street Furniture Australia product.
Handling
Handle the seat(s) and/or table(s) and parts in a manner to prevent scratching, warping, bending
and twisting. Do not slide parts on concrete or other hard or abrasive surfaces.
Delivery
Please check you have received the below items. Missing or damaged parts need to be reported
to a Street Furniture sales representative.
Tools required for assembly (not included)
7. Ratchet Drive Tool6. 8mm Ball Point Hex Key
1. Assembled Seat/Bench/Table 2. Legs x2 (Post Leg 05 is shown) 3. Bolts x4 4. Dome Nuts x4
5. Washer x4
2
43
1
5
This technical pack is copyright and owned by Street Furniture Australia Pty Limited ACN 070 910 100.
You may download and use this technical pack in unaltered form only for installing and maintaining our
products. All rights are reserved. Any use of our technical pack for purposes other than for the above-
mentioned purpose, is strictly prohibited without the prior written permission of Street Furniture Australia
Pty Limited, Level 1, 52-58 William Street, East Sydney NSW 2011. Street Furniture Australia Pty Limited
reserves the right to make modications to product specications without prior notice.
© Street Furniture Australia Pty Limited 2013. All rights reserved.
1800 027 799 streetfurniture.com
PAGE
leg assembly guide
SEATING, BENCHES AND TABLES
03
RECOMMENDED INSTALLATION PROCEDURE FOR ALL STREET FURNITURE LEG TYPES
(SEE ALL LEG TYPES ON PAGE 8)
1. Take two of the bolts and place one
washer on to each bolt against the head of
the bolt.
2. Take one of the legs and turn it upside
down. Insert the two bolts with the washers
into the bolt holes as shown in the image.
3. Place the assembled seat/bench/table
upside down and on to a protected surface to
prevent scratching.
4. Place the leg over the axle, aligning the
threaded bolts with the holes on the seat
frame upper support.
1
2
4
This technical pack is copyright and owned by Street Furniture Australia Pty Limited ACN 070 910 100.
You may download and use this technical pack in unaltered form only for installing and maintaining our
products. All rights are reserved. Any use of our technical pack for purposes other than for the above-
mentioned purpose, is strictly prohibited without the prior written permission of Street Furniture Australia
Pty Limited, Level 1, 52-58 William Street, East Sydney NSW 2011. Street Furniture Australia Pty Limited
reserves the right to make modications to product specications without prior notice.
© Street Furniture Australia Pty Limited 2013. All rights reserved.
1800 027 799 streetfurniture.com
PAGE
leg assembly guide
SEATING, BENCHES AND TABLES
03
RECOMMENDED INSTALLATION PROCEDURE FOR ALL STREET FURNITURE LEG TYPES
(SEE ALL LEG TYPES ON PAGE 8)
1. Take two of the bolts and place one
washer on to each bolt against the head of
the bolt.
2. Take one of the legs and turn it upside
down. Insert the two bolts with the washers
into the bolt holes as shown in the image.
3. Place the assembled seat/bench/table
upside down and on to a protected surface to
prevent scratching.
4. Place the leg over the axle, aligning the
threaded bolts with the holes on the seat
frame upper support.
1
2
4
This technical pack is copyright and owned by Street Furniture Australia Pty Limited ACN 070 910 100.
You may download and use this technical pack in unaltered form only for installing and maintaining our
products. All rights are reserved. Any use of our technical pack for purposes other than for the above-
mentioned purpose, is strictly prohibited without the prior written permission of Street Furniture Australia
Pty Limited, Level 1, 52-58 William Street, East Sydney NSW 2011. Street Furniture Australia Pty Limited
reserves the right to make modications to product specications without prior notice.
© Street Furniture Australia Pty Limited 2013. All rights reserved.
1800 027 799 streetfurniture.com
PAGE
leg assembly guide
SEATING, BENCHES AND TABLES
02
Thank you for purchasing a Street Furniture Australia product.
Handling
Handle the seat(s) and/or table(s) and parts in a manner to prevent scratching, warping, bending
and twisting. Do not slide parts on concrete or other hard or abrasive surfaces.
Delivery
Please check you have received the below items. Missing or damaged parts need to be reported
to a Street Furniture sales representative.
Tools required for assembly (not included)
7. Ratchet Drive Tool6. 8mm Ball Point Hex Key
1. Assembled Seat/Bench/Table 2. Legs x2 (Post Leg 05 is shown) 3. Bolts x4 4. Dome Nuts x4
5. Washer x4
2
43
1
5
assembly instructions
A. HOW TO ASSEMBLE THE LEGS
1. Please check that you have all the components Fig.1.
2. Make sure that you have the tools required Fig. 2.
3. Insert washers on two bolts Fig. 3.
4. Turn a leg upside down and insert bolt with washer Fig. 4. Fig. 3 Fig. 4
Fig. 2
Your components:
1. Assembled Seat/Bench/Table
2. Leg x2 (your selected design)
3. Bolts x4
4. Dome Nuts x4
5. Washer x4
Note: The Post leg is shown in this example, however this assembly
method is applicable to all leg types.
Your tools (not inlcuded):
1. 8mm Ball Point Hex Key
2. Ratchet Drive Tool
Fig. 1
6 7

© Street Furniture Australia Pty Limited ABN 46 070 910 100
Version 2 @ 25.06.21 MDP-07 streetfurniture.com
Australia 1800 027 799
United States [phone]
International [phone]
Email [email protected]
N6 391 Park Road, Regents Park
NSW 2143, Australia
A. HOW TO ASSEMBLE THE LEGS (continued)
5. Place the assembled seat/bench/table upside down and on to a
protected surface to prevent scratching. Place the leg over the axle
and align the threaded bolts with the holes Fig. 5.
6. Take one dome nut and carefully place it into the slotted hole Fig. 6.
7. Jiggle the bolt as shown in the photo so that the bolt thread catches
the dome nut. Repeat for the other bolt and dome nut Fig. 7.
8. Using a 8mm Hex Key and Rachet DriveTool (not included), tighten
both bolts Fig. 8.
Note: The leg casting does not need to be completely closed or
touching the frame upper support as long as the leg is tight and the
faces of the upper frame and leg casting are parallel.
9. Repeat the procedure with the other leg.
Correct Installation
Faces of the upper frame and leg casting are parallel.
Incorrect Installation
Faces on both castings are not parallel.
Fig. 7 Fig. 8
Fig. 5 Fig. 6
This technical pack is copyright and owned by Street Furniture Australia Pty Limited ACN 070 910 100.
You may download and use this technical pack in unaltered form only for installing and maintaining our
products. All rights are reserved. Any use of our technical pack for purposes other than for the above-
mentioned purpose, is strictly prohibited without the prior written permission of Street Furniture Australia
Pty Limited, Level 1, 52-58 William Street, East Sydney NSW 2011. Street Furniture Australia Pty Limited
reserves the right to make modications to product specications without prior notice.
© Street Furniture Australia Pty Limited 2013. All rights reserved.
1800 027 799 streetfurniture.com
PAGE
leg assembly guide
SEATING, BENCHES AND TABLES
03
RECOMMENDED INSTALLATION PROCEDURE FOR ALL STREET FURNITURE LEG TYPES
(SEE ALL LEG TYPES ON PAGE 8)
1. Take two of the bolts and place one
washer on to each bolt against the head of
the bolt.
2. Take one of the legs and turn it upside
down. Insert the two bolts with the washers
into the bolt holes as shown in the image.
3. Place the assembled seat/bench/table
upside down and on to a protected surface to
prevent scratching.
4. Place the leg over the axle, aligning the
threaded bolts with the holes on the seat
frame upper support.
1
2
4
This technical pack is copyright and owned by Street Furniture Australia Pty Limited ACN 070 910 100.
You may download and use this technical pack in unaltered form only for installing and maintaining our
products. All rights are reserved. Any use of our technical pack for purposes other than for the above-
mentioned purpose, is strictly prohibited without the prior written permission of Street Furniture Australia
Pty Limited, Level 1, 52-58 William Street, East Sydney NSW 2011. Street Furniture Australia Pty Limited
reserves the right to make modications to product specications without prior notice.
© Street Furniture Australia Pty Limited 2013. All rights reserved.
1800 027 799 streetfurniture.com
PAGE
leg assembly guide
SEATING, BENCHES AND TABLES
04
RECOMMENDED INSTALLATION PROCEDURE – LEGS
5. Take one dome nut and carefully place it
into the slotted hole in the frame near the axle
plate, with the flat facing the axle.
6. Jiggle the bolt as shown in the photo so that
the bolt thread catches the dome nut.
Repeat for the other bolt and dome nut.
7. Using a 8mm Hex Key and Rachet Drive
Tool (not included), tighten both bolts.
Note: The leg casting does not need to be
completely closed or touching the frame
upper support as long as the leg is tight and
the faces of the upper frame and leg casting
are parallel.
8. Repeat the procedure with the other leg.
Note: It is quite common to have legs fitted
correctly and have a parallel gap between the
faces as shown.
5
6
7
8
Correct installation - faces of
the upper frame and leg
castings are parallel
Incorrect installation - faces
on both castings are not
parallel
This technical pack is copyright and owned by Street Furniture Australia Pty Limited ACN 070 910 100.
You may download and use this technical pack in unaltered form only for installing and maintaining our
products. All rights are reserved. Any use of our technical pack for purposes other than for the above-
mentioned purpose, is strictly prohibited without the prior written permission of Street Furniture Australia
Pty Limited, Level 1, 52-58 William Street, East Sydney NSW 2011. Street Furniture Australia Pty Limited
reserves the right to make modications to product specications without prior notice.
© Street Furniture Australia Pty Limited 2013. All rights reserved.
1800 027 799 streetfurniture.com
PAGE
leg assembly guide
SEATING, BENCHES AND TABLES
04
RECOMMENDED INSTALLATION PROCEDURE – LEGS
5. Take one dome nut and carefully place it
into the slotted hole in the frame near the axle
plate, with the flat facing the axle.
6. Jiggle the bolt as shown in the photo so that
the bolt thread catches the dome nut.
Repeat for the other bolt and dome nut.
7. Using a 8mm Hex Key and Rachet Drive
Tool (not included), tighten both bolts.
Note: The leg casting does not need to be
completely closed or touching the frame
upper support as long as the leg is tight and
the faces of the upper frame and leg casting
are parallel.
8. Repeat the procedure with the other leg.
Note: It is quite common to have legs fitted
correctly and have a parallel gap between the
faces as shown.
5
6
7
8
Correct installation - faces of
the upper frame and leg
castings are parallel
Incorrect installation - faces
on both castings are not
parallel
This technical pack is copyright and owned by Street Furniture Australia Pty Limited ACN 070 910 100.
You may download and use this technical pack in unaltered form only for installing and maintaining our
products. All rights are reserved. Any use of our technical pack for purposes other than for the above-
mentioned purpose, is strictly prohibited without the prior written permission of Street Furniture Australia
Pty Limited, Level 1, 52-58 William Street, East Sydney NSW 2011. Street Furniture Australia Pty Limited
reserves the right to make modications to product specications without prior notice.
© Street Furniture Australia Pty Limited 2013. All rights reserved.
1800 027 799 streetfurniture.com
PAGE
leg assembly guide
SEATING, BENCHES AND TABLES
04
RECOMMENDED INSTALLATION PROCEDURE – LEGS
5. Take one dome nut and carefully place it
into the slotted hole in the frame near the axle
plate, with the flat facing the axle.
6. Jiggle the bolt as shown in the photo so that
the bolt thread catches the dome nut.
Repeat for the other bolt and dome nut.
7. Using a 8mm Hex Key and Rachet Drive
Tool (not included), tighten both bolts.
Note: The leg casting does not need to be
completely closed or touching the frame
upper support as long as the leg is tight and
the faces of the upper frame and leg casting
are parallel.
8. Repeat the procedure with the other leg.
Note: It is quite common to have legs fitted
correctly and have a parallel gap between the
faces as shown.
5
6
7
8
Correct installation - faces of
the upper frame and leg
castings are parallel
Incorrect installation - faces
on both castings are not
parallel
This technical pack is copyright and owned by Street Furniture Australia Pty Limited ACN 070 910 100.
You may download and use this technical pack in unaltered form only for installing and maintaining our
products. All rights are reserved. Any use of our technical pack for purposes other than for the above-
mentioned purpose, is strictly prohibited without the prior written permission of Street Furniture Australia
Pty Limited, Level 1, 52-58 William Street, East Sydney NSW 2011. Street Furniture Australia Pty Limited
reserves the right to make modications to product specications without prior notice.
© Street Furniture Australia Pty Limited 2013. All rights reserved.
1800 027 799 streetfurniture.com
PAGE
leg assembly guide
SEATING, BENCHES AND TABLES
04
RECOMMENDED INSTALLATION PROCEDURE – LEGS
5. Take one dome nut and carefully place it
into the slotted hole in the frame near the axle
plate, with the flat facing the axle.
6. Jiggle the bolt as shown in the photo so that
the bolt thread catches the dome nut.
Repeat for the other bolt and dome nut.
7. Using a 8mm Hex Key and Rachet Drive
Tool (not included), tighten both bolts.
Note: The leg casting does not need to be
completely closed or touching the frame
upper support as long as the leg is tight and
the faces of the upper frame and leg casting
are parallel.
8. Repeat the procedure with the other leg.
Note: It is quite common to have legs fitted
correctly and have a parallel gap between the
faces as shown.
5
6
7
8
Correct installation - faces of
the upper frame and leg
castings are parallel
Incorrect installation - faces
on both castings are not
parallel
This technical pack is copyright and owned by Street Furniture Australia Pty Limited ACN 070 910 100.
You may download and use this technical pack in unaltered form only for installing and maintaining our
products. All rights are reserved. Any use of our technical pack for purposes other than for the above-
mentioned purpose, is strictly prohibited without the prior written permission of Street Furniture Australia
Pty Limited, Level 1, 52-58 William Street, East Sydney NSW 2011. Street Furniture Australia Pty Limited
reserves the right to make modications to product specications without prior notice.
© Street Furniture Australia Pty Limited 2013. All rights reserved.
1800 027 799 streetfurniture.com
PAGE
leg assembly guide
SEATING, BENCHES AND TABLES
04
RECOMMENDED INSTALLATION PROCEDURE – LEGS
5. Take one dome nut and carefully place it
into the slotted hole in the frame near the axle
plate, with the flat facing the axle.
6. Jiggle the bolt as shown in the photo so that
the bolt thread catches the dome nut.
Repeat for the other bolt and dome nut.
7. Using a 8mm Hex Key and Rachet Drive
Tool (not included), tighten both bolts.
Note: The leg casting does not need to be
completely closed or touching the frame
upper support as long as the leg is tight and
the faces of the upper frame and leg casting
are parallel.
8. Repeat the procedure with the other leg.
Note: It is quite common to have legs fitted
correctly and have a parallel gap between the
faces as shown.
5
6
7
8
Correct installation - faces of
the upper frame and leg
castings are parallel
Incorrect installation - faces
on both castings are not
parallel

© Street Furniture Australia Pty Limited ABN 46 070 910 100
Version 2 @ 25.06.21 MDP-07 streetfurniture.com
Australia 1800 027 799
United States [phone]
International [phone]
Email [email protected]
N6 391 Park Road, Regents Park
NSW 2143, Australia
assembly instructions
B. HOW TO ASSEMBLE AN ANGLED ARM
1. Please check that you have all the components Fig.1.
2. Make sure that you have the tool required Fig. 2.
3. Align arm holes with seat casting holes Fig. 3.
4. Thread bolts through arm and seat casting holes Fig. 4. Fig. 3 Fig. 4
Fig. 2
Your components:
1. Seat Arms x1
2. Bolts x2
3. Washer x4 (2 washers per bolt)
4. Nuts x4
Your tools (not included):
1. 6mm Ball Point Hex Key
Fig. 1
4

© Street Furniture Australia Pty Limited ABN 46 070 910 100
Version 2 @ 25.06.21 MDP-07 streetfurniture.com
Australia 1800 027 799
United States [phone]
International [phone]
Email [email protected]
N6 391 Park Road, Regents Park
NSW 2143, Australia
B. HOW TO ASSEMBLE AN ANGLED ARM (continued)
5. Push the arm flush against the seat casting.
6. Take a dome nut and washer and secure it on the threaded end of
the bolt Fig. 5 and 6.
7. Using a 6mm Hex Key (not included), tighten the bolt on to the nut
Fig. 7.
8. Repeat step 6 and 7 for other hole. Fig. 7
Fig. 5
Fig. 6

© Street Furniture Australia Pty Limited ABN 46 070 910 100
Version 2 @ 25.06.21 MDP-07 streetfurniture.com
Australia 1800 027 799
United States [phone]
International [phone]
Email [email protected]
N6 391 Park Road, Regents Park
NSW 2143, Australia
installation instructions
A. HOW TO INSTALL THE PRODUCT ON SITE
Select the correct leg and mounting option for installation method.
Dimension provide is an estimation only. Measure the product on site for
exact dimension.
Note: installation hardware is not included.
Fig. 1: Splay
Fig. 2: Arch
Fig. 3: Splay Narrow
Fig. 2
Fig. 1
Fig. 3
65
65
65
520
520
585
365
430
585
5
5
5
80
80
80
32
32
32
01 SPLAY
03 SPLAY NARROW
02 ARCH
MOUNTING OPTIONS
MOUNTING OPTIONS
MOUNTING OPTIONS
Freestanding
Freestanding
Freestanding
Nylon Skid
Nylon Skid
Nylon Skid
Fastener by
Installer
2 Holes Ø14
2 Holes Ø14
2 Holes Ø14 Fastener by
Installer
Fastener by
Installer
(Dynabolt M12 x 120mm
recommended)
(Dynabolt M12 x 120mm
recommended)
(Dynabolt M12 x 120mm
recommended)
Surface Fixed
Surface Fixed
Plan
Plan
Plan
Elevation
Elevation
Elevation
Surface Fixed
Sub-surface Fixed
Sub-surface Fixed
Sub-surface Fixed

© Street Furniture Australia Pty Limited ABN 46 070 910 100
Version 2 @ 25.06.21 MDP-07 streetfurniture.com
Australia 1800 027 799
United States [phone]
International [phone]
Email [email protected]
N6 391 Park Road, Regents Park
NSW 2143, Australia
A. HOW TO INSTALL THE PRODUCT ON SITE (continued)
Fig. 4: Pedestal
Fig. 5: Post
Fig. 6: Tee (Not applicable for Classic Promenade Seat) Fig. 6
Fig. 5
65 50 100
150 160
200
200 80
300
05 POST MOUNTING OPTIONS
Surface Fixed
Fastener by
Installer Epoxy Mortar
by Installer
Sub-surface Fixed Core Drilled
Plan
Elevation
65
520
585
5
80
32
06 TEE MOUNTING OPTIONS
Freestanding
Nylon Skid
Fastener by
Installer
Plan
Elevation
Surface Fixed Sub-surface Fixed
Fig. 4
75
180
180
215 80
04 PEDESTAL MOUNTING OPTIONS
Fastener by
Installer
Surface Fixed
Plan
Elevation
Sub-surface Fixed
(Dynabolt M12 x 120mm
recommended)
(Dynabolt M12 x 120mm
recommended)
(Dynabolt M12 x 120mm
recommended)
2 Holes Ø14
4 Holes Ø14 2 Holes Ø14
2 Holes Ø14

© Street Furniture Australia Pty Limited ABN 46 070 910 100
Version 2 @ 25.06.21 MDP-07 streetfurniture.com
Australia 1800 027 799
United States [phone]
International [phone]
Email [email protected]
N6 391 Park Road, Regents Park
NSW 2143, Australia
A. HOW TO INSTALL THE PRODUCT ON SITE (continued)
Check which leg and mounting options are applicable with your selected
configurations. There are multiple leg designs that are presented in this
section, each has different mounting options. Make sure to follow the
one that you have ordered.
Fig. 7: Wall Mount
Fig. 8: Tee Table
Fig. 7
Fig. 8
Fastener by
Installer
40 180
140
125
260 TO FGL.
165
180
395
07 WALL MOUNT
08 TEE TABLE
MOUNTING
MOUNTING
Plan
Elevation
Elevation
Plan
Surface Fixed
Surface Fixed
(Dynabolt M12 x 120mm
recommended)
3 Holes Ø14
615
550
550
615
5
80
32
Nylon Skid
Fastener by
Installer
(Dynabolt M12 x 120mm
recommended)

© Street Furniture Australia Pty Limited ABN 46 070 910 100
Version 2 @ 25.06.21 MDP-07 streetfurniture.com
Australia 1800 027 799
United States [phone]
International [phone]
Email [email protected]
N6 391 Park Road, Regents Park
NSW 2143, Australia
A. HOW TO INSTALL THE PRODUCT ON SITE (continued)
Fig. 9: Tee Narrow (Only for Mall Slim Bench and Classic Galleria Slim Bench)
Fig. 10: Wall Narrow (Only for Mall Slim Bench and Classic Galleria Slim Bench)
Fig. 11: Plinth Mount Fig. 11
80
270 TO FGL.
160
200
36
160 40 40
45
12
11 PLINTH MOUNT MOUNTING
Plan
Elevation
Surface Fixed
Fastener by
Installer
(Dynabolt M12 x 120mm
recommended)
2 Holes Ø14
Fig. 10
Fastener by
Installer
40 150
110
100
260 TO FGL.
140
150
315
10 WALL NARROW MOUNTING
Plan
Elevation
Surface Fixed
(Dynabolt M12 x 120mm
recommended)
3 Holes Ø14
Fig. 9
65
375
440
5
80
32
09 TEE NARROW MOUNTING OPTIONS
Freestanding
Nylon Skid
Fastener by
Installer
Plan
Elevation
Surface Fixed Sub-surface Fixed
(Dynabolt M12 x 120mm
recommended)
2 Holes Ø14

© Street Furniture Australia Pty Limited ABN 46 070 910 100
Version 2 @ 25.06.21 MDP-07 streetfurniture.com
Australia 1800 027 799
United States [phone]
International [phone]
Email [email protected]
N6 391 Park Road, Regents Park
NSW 2143, Australia
additional information
‘SLUG’ SEAT DIVIDER (RETROFIT ONLY)
‘Slug’ is a seat divider designed to minimise damage to battens from
skateboard use. ‘Slug’ may be ordered assembled with the SFA seat or
bench, or ordered separately to be installed on site. The box on the right
shows how to retrofit the seat divider.
Top Perspective Bottom Perspective
Typical set-out for 3-seater (1750mm)
HOW TO INSTALL
WHERE TO INSTALL
Use indicator groove to
mark out distance back
from front of batten Drill Ø 12 blind hole. Drill Ø 7 through hole.
Note: The divider must face outwards
Classic Galleria / Promenade range
Detail Detail
Mall range
PARTS REQUIRED:
• 6mm screws (button head)
• Thread adhesive equal to Loctite 271
• Flat washers where appropriate
Note: SFA recommends security screws, equal to
Post Hexagon Socket Buttonhead Machine screws,
metric thread
TOOLS REQUIRED:
• Hand drill
• Drill bits (12dia and 7dia)
• Drill bit stop
• Suitable screwdriver
For extra strength, add a drop of
adhesive (ie Loctite 271) to thread
of slug. Insert screw.
Push ‘slug’
hard against
batten face
Ø 12
16
50 50550 550 550
7 min.
8 min.
M6 screw
Seat SeatBench BenchSlim Bench Slim Bench

© Street Furniture Australia Pty Limited ABN 46 070 910 100
Version 2 @ 25.06.21 MDP-07 streetfurniture.com
Australia 1800 027 799
United States [phone]
International [phone]
Email [email protected]
N6 391 Park Road, Regents Park
NSW 2143, Australia
assembly instructions
C. HOW TO ASSEMBLE AN ELLIPTICAL ARM
1. Please check that you have all the components Fig.1.
2. Make sure that you have the tool required Fig. 2.
3. Align arm holes with seat casting holes Fig. 3.
4. Thread bolts through arm and seat casting holes Fig. 4. Fig. 3 Fig. 4
Fig. 2
Your components:
1. Seat Arms x1
2. Bolts x2
3. Washer x2
4. Nuts x4
Fig. 1
Your tools (not included):
1. 6mm Ball Point Hex Key
2. Torx Allen Key