STRIKEWORTH TriSport User manual

3 in 1 Multi-Game Table
Assembly Manual
Please note, a full colour PDF manual complete with step by step
images can be downloaded at www.strikeworth.eu/trisport

Parts Idencaon:- We recommend that all parts are laid out in order on the oor
prior to starng the construcon procedure. Please note that the triangular shaped
panels marked #P4 and #P5 are dierent. Focus on idenfying panel #P4 rst - put
the triangle piece on the oor as shown in the image below. Ensure one goal open-
ing is facing you and the other on your right.
The distance from the goal mouth facing you and the boom edge is shorter on
panel #P4 than panel #P5. You may wish to use a measuring tape as shown below
to make sure. For #P4 the goal mouth facing you should measure approximately
8cm from the boom lip to the end of the panel.
Please note that some tables come with an addional pack of nuts, bolts and
screws that are intended as an upgrade or replacement to the standard ones in this
kit.

PART S IDENTIFIER
(NoT o Scale)
#P1
#P6
#P 11
#P16 #P17 #P18 #P19 #P20
#P12 #P13 #P14 #P15
#P8 #P9 #P10
#P3 #P4 #P5
1 PC
Pool table /Hockey
side apron
1 PC
Hockey Goal Box
2 PCS
Scoccer Goal Box
2 PCS
5 Player (Blue)
RodA ssembled
1 PC
Plastic Washer
8 PCS
3 Player (Blue)
RodA ssembled
1 PC
5 Player (Red)
RodA ssembled
1 P C
3 Player (Red)
RodA ssembled
1 PC
2 PCS
Player rod Stopper
8 PCS
Leg
2 PCS
Position lock
system
2 PCS
Pool table /Scoccer
side apron
1 PC
Hockey /Soccer
side apron
1 PC
Leg support brace
1 PC
6 PCS
1 PC 1 PC
End ApronA
1 PC
End Apron B
1 PC
#P21
#P26 #P27 #P28 #P29 #P30
#P31 #P32 #P33 #P34 #P35
#P22 #P23 #P24 #P25
WARNING:
Choking Hazard - -T able contains small balls and/
or small parts.
!
(A ssembled )(A ssembled )(A ssembled )
(A ssembled)
Manual Slide Scorer
4 PCS
Hand Grips
8 PCS
)delbmessA(
1/4"X65mm Bolt
8 PCS
#P2
Leg leveler
4 P CS
Player Rod Washer set
8 SETS
Foam Bumper
8 PCS
24 PCS
3/16"X45mm Bolt
Soccerend rail
Fixed
6 P CS
3.5X15mm Flat
Head screws
24 PCS
#P7
system
Position lock
2 SET
1 PC
AssembledRod
2 Player (Blue)
Assembled )(
1 Player (Blue)
RodA ssembled
1 PC
Assembled )(
1 PC
AssembledRod
2 Player (Red)
)Assembled( (A ssembled)
1 Player (Red)
RodA ssembled
1 PC

Allen Key
1 PC
Fan
1 PC
Wrench
1 PC
#P36 #P37
#P41 #P42 #P43 #P44 #P45
#P38 #P39 #P40
Inner Nut
8 PCS
1.5” Billard Ball
1 Set
Pusher-Red
2 PCS Round Puck-Red
2PCS
Soccer Ball
2 PCS
Chalk
2 PCS
42" Billard Cue
2 PCS
PlasticT riangle
1 PC
Brush
1 PC
Acorn Nut
8 PCS
Plastic corner pocket
4 P CS
4X45mm
Screws
50 PCS
Plastic side pocket
2 PCS
#A1
#A6 #A7 #A8
#A2 #A3 #A4 #A5
WARNING:
Choking Hazard -- Table contains small balls and/
or small parts.
!
3.5X28mm
Screws
36 PCS
3.5X12mm Flat
Head screws
16 PCS
3.5X18mm Flat
Head screws
8 PCS 8 PCS
#P46
1/4" Washer set
2 PCS
Nut
#P47 #P48 #P49 #P50
M12 Spacer Nut
2 PCS
#P51
M12 Washer
2 PCS
M8 Washer
2 PCS
#P52
PARTS IDENTIFIER
(not to scale)
ACCESSORY IDENTIFIER
(not to scale)
Cable Clip
1 PC
#P53
Long Screw
4 PCS

Step 1 :
a) Place air hockey playeld #P2 face down on a carpeted oor and aach fan #P44
including protecon grill to the circular cut out using P53 screws. NOTE:- ensure air
ow arrow is facing downwards direcng air into the circular opening! - this indica-
tor can be found on the side of the fan. The label on the centre of the fan should
also be facing downwards: TIP : don’t over ghten screws
Air Flow Indicator
b) Aach side apron #P6 to Triangular end apron P4 using P40 screws as shown
in diagram below - please note that the cable from the air hockey fan should be
passed through the hole in the side apron.
c) Next line up the air hockey playeld in the recess of side Apron #P6 and secure
down the side using #P41 screws - TIP, you may nd it easier to stand the struc-
ture on end at this point to line up the playeld - see images of the live procedure
below diagram
d) Finally aach side apron #P8 as shown, again ensure air hockey playeld is
neatly in the recess an ush with the Triangle end apron P4 before securing on
both sides with the screws.

#P4
#P40
#P8
#P6
#P2
#P41
#P41
#P53
#P44
IMPORTANT!
Ensure triangle piece
is correct
[see page 1]
Step 1
Live build images:

Step 2 :
a) Aach the playeld support braces as shown in the diagram, be sure to check
the orientaon of the bar in queson to check if it is to be secured on its side or in
a more upright posion. For those bars desned to support the football pitch en-
sure they are secured in line with the grooves. You may wish to rotate the structure
to get beer access. Helpful images on the next page.
b) Once support braces are in place, oer up side apron P7 to be aached.
#P40
#P40
#P40
#P40
#P7
#P9
#P16
#P4

Step 3 :
a) before sliding the football pitch into place as per the diagram below, ensure that
one of the football end rails P16 is aached & seated in place using P40 screws.
b) When inserng the football pitch you may nd it easier to slightly loosen o the
screws aaching panel P7 to the support braces - these can be re ghtened when
the pitch is in place
c) When the pitch is in place insert the second goal end panel P16 and aach to P7
and P8 using P40 screws as indicated
#P3
#P40
#P16
#P40
#P40
#P40

Step 4 :
a) Aach triangle end apron P5 to the structure making clear note of its orienta-
on shown in the diagram.
b) Aach both P11 (hockey goal box) and P12 (football goal boxes) as indicated us-
ing P41 screws, note that this must be completed on both ends of the table
c) aach P34 metal plates using P33 screws to both Triangle end Aprons P4 and P5
as indicated
d) This is also the me to double check that the air hockey power lead and plug
have been passed through the exit hole
#P40
#P5
#P7
#P6
#P11
#P12
#P41
#P34
#P33

Step 5 :
a) Screw in levelling feet into P13 metal leg structure by hand
b) Take P13 leg structure and push P15 lock through the upper central hole. Now
put nut P49 on and spin down the thread.
c) Place washer P50 over the thread and with the body of the table on end, oer
up the leg structure pushing P15 into the central hole in the triangle end apron P4/
P5
d) Reaching inside the table put P15 spacer over the protruding thread and up into
the hole, secure the spacer with Nut 46 and naly with wing nut P46 - see photo
images below main illustraon
Repeat the above on both sides of the table
e) bolt on leg support pannels P10 to the legs using P30 bolts and P45 washer
#P14
#P13
#P17
#P45
#P30
#P10
#P46
#P15
#P15
#P51
#P50
#P49

Step 6 :
a) Now put the structure on to its legs - best way is to li the body of the table up
and the legs will swing down into posion - we recommend loosely inserng lock-
ing nut P14 to keep the table stable.
b) Insert the pool table playeld P1 into the structure. Introduce the board evenly
being careful not to catch the nets. You can loosen o P40 screws as shown below
to help. Once in place use your ngers to pull up any cushions that have sunk be-
low the level of the side aprons so they are ush.
P.5
#P40
#P1
#P9
(loosen o if required)

Step 6(b) :
Please use cable clip P52 to secure air hockey mains lead and plug

Step 7 :
a) Ensuring it is ush with the edges, secure pool table playeld using x18 P41
screws as indicated in the diagram
b) Insert the rubber pocket liners into each pocket cavity behind the metal wires.
Secure these to the MDF using the small screws P42. There are no pilot holes but
generally orientate the screw to the top corners of the rubber and don’t over ght-
en. A screw can also be used vercally on the top lip of the liners to secure them.
b) Now rotate table onto air hockey side and lock in place ready to aach scoring
sliders P31 to the table using P43 screws
#P38
#P39
#P42
#P1
#P43
#P31
#P41
#P41

Step 7 :
a) rotate table and lock into place at football table side - now aach scoring sliders
P31 to the table using P43 screws
Rod inseron procedure
b) Starng with the goalie /single player rod and face player correct way. insert the
thick/ handle through the hole with the plasc trim (double check both sides of
this rod have a spring aached)
c) Now locate the thin rod and slide washer P18 over the spiked end
d) Insert spiked end into the cavity of the thicker rod
e) Find the at end of the thin rod and use part 36 (inner nut) to surround it, push-
ing both sides into place
f) Now push the completed inner nut though the hole with no trim
g) take Part P37 and ghten onto the inner nut from the outside edge – use span-
ner to complete
h) Use a rubber mallet to knock handle onto the rod.
#P32
#P27
#P28
#P25
#P26
#P24
#P22
#P37
#P19
#P23
#P21
STEP8A
#P20
#P32
#P22
#P18
#P36
#P37
#P29
#P43
#P31