Strong SRT 6010 User manual

Picture simulated

PART 1 zEnglish
2
Content
1.0 Introduction 3
1.1 Safety Instructions 3
1.2 Features & Accessories 4
1.3 Safety Precautions 5
1.4 Storage 5
1.5 Equipment Set-up 6
2.0 Your Receiver 6
2.1 Front Panel 6
2.2 Remote Control Unit 7
2.3 Rear Panel 9
3.0 Connections 10
3.1 Connecting to TV & VCR 10
3.2 Connecting to Digital Audio Amplifier 11
3.3 Connecting to Satellite Dish 11
3.4 Connecting to serial cable for downloading software 13
4.0 Starting up 14
5.0 Main Menu 18
5.1 Channel Organiser 19
5.2 Installation 23
5.3 System setting 29
5.4 Timer 39
5.5 Game 40
6.0 Other operation functions 42
6.1 System Information 42
6.2 Mosaic (Nine picture view) 42
6.3 EPG (Electronic Program Guide) 43
6.4 Selection Audio Language 45
6.5 Teletext function 45
A.1 Trouble Shooting 47
A.2 Specifications 48
A.3 Glossary of Terms 50
UM DVB-S English 16/9/05 10:23 AM Page 2

PART 1 zEnglish
3
1.0 Introduction
1.1 Safety Instructions
DO NOT INSTALL YOUR RECEIVER:
In a closed or poorly ventilated cabinet;
Directly on top of or under any another equipment;
On a surface which might obstruct the ventilation slots.
DO NOT EXPOSE THE RECEIVER OR ITS ACCESSORIES:
To direct sunlight or near any other equipment that generates heat;
To rain or intense moisture;
To any shock which may cause permanent damage to your receiver;
To any magnetic objects, such as loudspeakers, transformers, etc.;
To intense vibration;
Never open the cover. It is dangerous to touch the inside of the receiver due to high voltage
currents and possible electrical hazards. Your warranty will be void if the receiver has been
opened.
When the receiver is not used for a long period of time, you should unplug the power cord
from the wall socket.
Do not use a damaged power cord. It may cause a fire or an electrical shock.
Do not touch a power cord with wet hands. It may cause an electric shock.
Place the receiver in a well-ventilated environment.
When you are connecting the cables, be sure that the receiver is disconnected from the
mains supply voltage.
Do not use your receiver in a humid environment.
Make sure you read this user manual before installing your receiver.
How to Use This Manual
This manual provides complete instructions for installing and using this receiver.
The following symbols will serve as follow.
Warning Indicates warning information.
Tips Indicates any other additional important or helpful information.
MENU Represents a button on the remote control or the receiver (Bold Character)
Move to Represents a menu item within a window. (Italic Character)
UM DVB-S English 16/9/05 10:23 AM Page 3

PART 1 zEnglish
4
1.2 Features & Accessories
For all digital Free-To-Air TV and Radio programmes via satellite
Display showing channel number or time 1
Digital sound through coaxial output (S/PDIF) 1
Separate power switch
Set-up supports for first time installation
3200 channel memory capacity for 64 satellites
4 Favourite lists for TV-and Radio programme
Quick and easy installation & user-friendly menu
Excellent Audio & Video quality
Parental lock function for menu and selectable per channel
Teletext via OSD & VBI
Supports DiSEqC 1.0 and DiSEqC 1.2
Electronic Programme Guide (EPG) for present/following event information and up to 7
days for on screen programme information
Full multi-lingual DVB subtitling and audio track support
Multi-lingual support on screen menu (OSD): English, German, French, Italian, Spanish,
Turkish, Bulgarian, Czech
Edit functions for TV or Radio programme name and satellite name
Future-proof: Software update via satellite (OTA)
Signal strength bar for digital transponders
Automatic, Network and manual channel scan options
Power on with last viewed channel
10 Timer for recording and/ or sleep-timer with 3 modes (daily, weekly, once)
1Game (Tetris)
User-friendly remote control with coloured function buttons
Low power consumption
Advanced timer function
Mosaic function: 9 TV Channel in overview
Automatic clock change: summer/ winter time
Connections: SAT IN, SAT OUT, 1 Scart TV (RGB/CVBS), 1 Scart VCR (CVBS)1, S/PDIF 1,
Serial Port RS 232, Power switch
1Only for model SRT 6010
Accessories:
User's Manual
1 Remote control unit
2x Batteries (AAA type)
UM DVB-S English 16/9/05 10:23 AM Page 4

PART 1 zEnglish
5
Note: The batteries should not be recharged, disassembled, electrically short-circuited or be mixed or
used with other types of batteries.
1.3 Safety Precautions
To maintain your receiver's optimum performance, you are advised to apply the following safety precautions:
Read this manual carefully and make sure you fully understand the instructions given.
Refer all maintenance or servicing to suitably qualified personnel
If you wish, you may clean your receiver with a soft lint-free cloth slightly made damp with a
mild soap solution, only after disconnecting from the mains voltage supply.
Do not use alcohol or ammonia based liquids to clean the receiver.
Do not open the receiver cover, as you will be exposed to a shock hazard
Do not open the receiver cover this will void your warranty.
Do not place any objects on top of the receiver because this might prevent proper cooling
of the components inside.
Make sure no foreign objects fall through the ventilation slots because this could cause fire
or an electric shock.
Wait a few seconds after switching off the receiver before you move the receiver or discon-
nect any equipment.
Please ensure that the electrical power supply corresponds with the voltage on the electrical
identification plate at the back of the receiver.
It is a necessity that you only use an approved extension and compatible wiring that is suit-
able for the electrical power consumption of the installed equipment.
If the receiver does not operate normally even after strictly following the instructions in this
user manual, it is recommended to consult your dealer.
1.4 Storage
Your receiver and its accessories are stored and delivered in a packaging designed to protect against
electric shocks and moisture. When unpacking it, make sure that all the parts are included and keep
the packaging away from children. When transporting the receiver from one place to another or if you
are returning it under warranty make sure to repack the receiver in its original packaging with its acces-
sories. Failing to comply with such packaging procedures could void your warranty.
UM DVB-S English 16/9/05 10:23 AM Page 5

PART 1 zEnglish
6
1.5 Equipment Set-up
We recommend you consult a professional installer to set up your equipment. Otherwise, please follow
the instructions below:
Refer to the user manual of your TV and your antenna.
Make sure that the SCART cable is in a good condition.
Make sure that the SCART cable connections are well shielded
Make sure that the outdoor components of the antenna are in good condition.
2.0 Your Receiver
2.1 Front Panel
FIGURE 1. Front Panel
1. Mode indicator
The RED light indicates that the receiver is in STAND-BY mode.
The GREEN light indicates that the receiver is in AWAKE mode.
2. 4 digits display 1
In STAND-BY mode this indicates current time
In AWAKE mode this indicates current channel number
1Only for model SRT 6010
UM DVB-S English 16/9/05 10:23 AM Page 6

PART 1 zEnglish
7
2.2 Remote Control Unit
All features of the set-top box can be controlled with the remote control unit.
K. 
Change the current program to the previous/next program
when menu is off. Moves the cursor to upward/downward
when menu is on.
L.. 
Increases/decreases the volume level when menu is off. Change the setting values in specific
Menu item when menu is on.
M. OK
Activates the highlighted menu item. Displays a channel list according to TV /Radio Mode.
N. V+ / V-
Use to increase or decrease the receiver volume level.
O. P+ / P-
Page up and down in menu list.
FIGURE 2.
Remote Control Unit
C. AV
Toggle between TV and AV mode.
D. 0~9
Changes channel and controls numeric functions.
E. FAV
Toggle Favorite mode ON / OFF.
F. TV/R
Toggle between TV or RADIO mode.
G. MENU
Shows the main menu and exits from any level of menu
to view mode.
H. INFO
Shows information of the current channel.
I. EPG
Shows the EPG (Electronic Program Guide) only when
menu is off.
J. EXIT
Exits from the menu or sub-menu and cancels the
progressing function if applicable.
A. Turns the receiver On/Off.
B. Mutes audio output of the receiver.
UM DVB-S English 10/14/05 12:57 PM Page 7

PART 1 zEnglish
8
O. P+ / P-
Page up and down in menu list.
P. MOSAIC
Show pictures of 9 channels on the screen simultaneously
Q. PAUSE
Freeze/Resume picture.
R. AUDIO
Shows the list of available audio languages for the channel you are watching. In addition it sets
the current channel audio to stereo ((z)), left-mono ((zor right-mono z)).
S. EDIT
Program edit
T. SAT
Switch the satellite
U. TEXT
Shows current service's Teletext on OSD
V. SUB
Show the list of subtitled languages the current channel supports.
W. RECALL
Switches back to last channel viewed
UM DVB-S English 16/9/05 10:23 AM Page 8

PART 1 zEnglish
9
2.3 Rear Panel
FIGURE 3. Rear Panel
1. SAT IN
Connect the digital signal from your LNB on the satellite dish to this connector.
2. SAT OUT
Gives you the possibility to connect an extra receiver (analogue or digital).
3. TV SCART Connector
To connect your receiver to your TV set using a SCART cable.
4. VCR SCART Connector 1
To connect your receiver to your video recorder using a scart cable. Your video signal will now
be looped through your receiver to your TV set.
5. RS 232 Serial Port
This serial port can be used to connect your PC with your receiver, to download new versions
of software to your receiver.
6. S/PDIF Digital audio output 1
Use this coaxial output to connect your receiver to the input of your digital audio amplifier.
7. Power ON/OFF Switch
8. Power Cord
Your receiver requires a current of 90~240V AC (Auto-selectable), 50~60Hz +/-5%.
Make sure to check the power specification before connecting your receiver to the wall outlet.
1Only for model SRT 6010.
UM DVB-S English 16/9/05 10:23 AM Page 9

PART 1 zEnglish
10
3.0 Connections
3.1 Connecting to TV & VCR
< Basic connection with a Scart cable >
1. Connect the satellite signal from the LNB to the LNB IN connector.
2. Connect the TV scart connector at the back of the receiver to the scart - in connector on your TV set.
FIGURE 4. Basic connection with a Scart cable
<Advanced connection of the receiver to the TV set and VCR>
1. Connect the satellite signal from the LNB to the LNB IN connector.
2. Connect the TV scart connector at the back of the receiver to the scart-in connector on your TV set.
3. Connect the VCR scart connector at the back of the receiver to the scart-in connector on your VCR.
FIGURE 5. Advanced connection of the receiver to the TV set and VCR
UM DVB-S English 16/9/05 10:23 AM Page 10