Strong SRT 3002 User manual

User Manual
Bedienungsanleitung
Uživatelská příručka
Používateľská príručka
Használa útmutató
Ръководство за употреба
Digital HD Cable Receiver
SRT 3002
Picture similar

Digital HD Cable Receiver SRT 3002
Supplied by STRONG Austria
CABLE IN
500 mA max.USB: 5 V
TV SCART
CABLE OUT
COAXIAL
S/PDIF
12 V ,
0.5 A, max. 6 W
MANUFACTURED UNDER LICENSE FROM DOLBY LABORATORIES.
DOLBY AUDIO AND THE DOUBLE-D SYMBOLARE TRADEMARKS OF DOLBY LABORATORIES
HDMI
Fig. 1
Fig. 2
Fig. 3
45321
1 2 3 4 5 6
2
13
12
Fig. 4Fig. 5
1
45
6
13
7
8
9
10
11
12
14
16
15
19
17
17
20
24
27
28
21 22 23
18
25
28
26
30
29
3

Fig. 6
Fig. 7
Fig. 8
USB
storage device
USB Cable
Digital HD Cable Receiver SRT 3002
Supplied by STRONG Austria
CABLE IN
500 mA max.USB: 5 V
TV SCART
CABLE OUT
COAXIAL
S/PDIF
12 V ,
0.5 A, max. 6 W
MANUFACTURED UNDER LICENSE FROM DOLBY LABORATORIES.
DOLBY AUDIO AND THE DOUBLE-D SYMBOLARE TRADEMARKS OF DOLBY LABORATORIES
HDMI
HDMI
Cable
SCART
Cable
(optional)
Television
Digital Audio
Amplifier S/PDIF
Cable
Cable
Broadcast
2 HDMI
Cables
Digital HD Cable Receiver SRT 3002
Supplied by STRONG Austria
CABLE IN
500 mA max.USB: 5 V
TV SCART
CABLE OUT
COAXIAL
S/PDIF
12 V ,
0.5 A, max. 6 W
MANUFACTURED UNDER LICENSE FROM DOLBY LABORATORIES.
DOLBY AUDIO AND THE DOUBLE-D SYMBOLARE TRADEMARKS OF DOLBY LABORATORIES
HDMI
Digital Audio
Amplifier
Television

16 Aug 2018 17:01
Supplied by STRONG Austria
Represented by
STRONG Ges.m.b.H.
Franz-Josefs-Kai 1
1010 Vienna
Austria
Email: [email protected]

12 Oct 2018 16:15
Your receiver is delivered with USB multimedia support. After downloading the optional software for
recording via USB from our webshop at www.strong.tv, the receiver can be upgraded to support the
recording function via USB. This user manual describes the full functionality including the recording
function and may not be applicable if the software for recording via USB has not yet been installed.
Licenses
THIS PRODUCT IS LICENSED UNDER THE AVC PATENT PORTFOLIO LICENSE FOR THE PERSONAL AND
NONCOMMERCIAL USE OF A CONSUMER TO (i) ENCODE VIDEO IN COMPLIANCE WITH THE AVC STANDARD (“AVC
VIDEO”) AND/OR (ii) DECODE AVC VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN A PERSONAL AND
NON-COMMERCIAL ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED TO PROVIDE AVC VIDEO.
NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER USE. ADDITIONAL INFORMATION MAY BE OBTAINED
FROM MPEG LA, L.L.C. SEE HTTP://WWW.MPEGLA.COM
This product contains one or more programs protected under international and U.S. copyright laws as unpublished
works. They are confidential and proprietary to Dolby Laboratories. Their reproduction or disclosure, in whole or
in part, or the production of derivative works therefrom without the express permission of Dolby Laboratories is
prohibited. Copyright 2003-2009 by Dolby Laboratories. All rights reserved..
1
English

TABLE OF CONTENTS
1.0 INTRODUCTION 3
1.1 Safety Instructions 3
1.2 Storage 4
1.3 Equipment Set-up 4
1.4 Accessories 4
1.5 Usage of external USB devices 4
2.0 YOUR RECEIVER 5
2.1 DEFAULT PIN: 1234 5
2.2 Front Panel 5
2.3 Rear Panel 5
2.4 Remote Control 5
2.5 Installing the batteries 6
2.6 Using the remote control 6
3.0 CONNECTION 6
3.1 Connecting to cable TV 6
3.2 Connecting to TV with HDMI cable 6
3.3 Connecting to TV with SCART cable 7
3.4 Connecting to a Digital Audio Amplifier with S/PDIF 7
3.5 Connecting to a Digital Audio Amplifier and TV using HDMI 7
3.6 Connecting a USB storage device 7
4.0 STARTING UP FOR THE FIRST TIME 7
4.1 DVB-C Installation 8
5.0 QUICK GUIDE TO USING YOUR RECEIVER 8
6.0 OPERATION 9
6.1 Changing channels 9
6.2 Info Banner 9
6.3 Selection of audio language 9
6.4 Teletext 9
6.5 Subtitles 10
6.6 Timeshift* 10
6.7 EPG (Electronic Programme Guide) 10
6.8 Instant Recording* 10
7.0 MAIN MENU 10
7.1 Edit Channel 11
7.2 Installation 12
7.3 System Setup 13
7.4 Tools 15
7.5 Media Player* 17
8.0 TROUBLESHOOTING 19
9.0 TECHNICAL SPECIFICATIONS 20
STRONG declares that this item complies with the basic requirements and other relevant regulations of directives EMC 2014/30/EU, LVD
2014/35/EU and RoHS 2011/65/EU.
The EU declaration of conformity is available at the following internet address: http://www.strong.tv/en/doc
Subject to alterations. In consequence of continuous research and development technical specifications, design and appearance of products
may change. HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC
in the United States and other countries. Manufactured under license from Dolby Laboratories. Dolby Audio, Dolby Digital, Dolby Digital Plus
and the double-D symbol are registered trademarks of Dolby Laboratories. All other product names are trademarks or registered trademarks
of their respective owners.
© STRONG 2018. All rights reserved.
2

1.0 INTRODUCTION
1.1 Safety Instructions
Read all of the instructions before operating the device. Keep these instructions well for later use.
 Only use attachments/accessories specified or provided by the manufacturer (such as the exclusive supply
adapter, battery etc.).
 Please refer to the information on the product enclosure for electrical and safety information before installing or
operating the apparatus.
 To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
 The ventilation should not be impeded by covering the ventilation openings with items, such as newspaper,
table-cloths, curtains, etc.
 The apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall
be placed on the apparatus.
 This mark indicates a risk of electric shock.
 To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation
instructions.
 Danger of explosion if the battery is incorrectly replaced. Replace only with the same or equivalent types.
 The battery (battery or batteries or battery pack) shall not be exposed to excessive heat such as sunshine, fire or
the like.
 Excessive sound pressure from earphones and headphones can cause hearing loss.
Listening to music at high volume levels and for extended durations can damage one's hearing.
 In order to reduce the risk of damage to hearing, one should lower the volume to a safe, comfortable level, and
reduce the amount of time listening at high levels.
 The mains plug or appliance coupler is used as disconnect device, it shall remain readily operable. When not in
use and during movement, please take care of the power cord set, e.g. tie up the power cord set with cable tie
or something like that. It shall be free from sharp edges or similar which can cause abrasion of the power cord
set. When put into use again, please make sure the power cord is not damaged. The absence of a light indication
on the apparatus does not mean that it is fully disconnected from the mains. To disconnect the apparatus
completely, the mains plug must be pulled out.
 Attention should be drawn to environmental aspects of battery disposal.
 No naked flame sources, such as lighted candles, should be placed on the apparatus.
 To prevent the spread of fire, keep candles or other open flames away from this product
at all times.
 Equipment with this symbol is a Class II or double insulated electrical appliance. It has been designed in
such a way that it does not require a safety connection to electrical earth.
Precautions
 Never try to open the device. It is dangerous to touch the inside of the device due to high voltages and possible
electrical hazards. Opening the device will void the warranty of the product. Refer all maintenance or servicing to
suitably qualified personnel.
 When you are connecting cables, be sure that the device is disconnected from the mains supply voltage. Wait a
few seconds after switching off the device before you move the device or disconnect any equipment.
 It is a necessity that you only use an approved extension and compatible wiring that is suitable for the electrical
power consumption of the installed equipment. Please ensure that the electrical power supply corresponds with
the voltage on the electrical identification plate at the back of the device.
Operating Environment
 Do not install this equipment in a confined space such as a bookcase or similar unit.
 Do not use the set near damp, and cold areas, protect the set from overheating.
 Keep away from direct sunlight.
 Do not use the set near dust place.
 Do not place candles near the opening area, to avoid flammable foreign material from entering the device.
3
English

WEEE Directive
Correct Disposal of this product. This marking indicates that this product should not be disposed with other
household wastes throughout the EU. To prevent possible harm to the environment or human health from
uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources.
To return your used device, please use the return and collection systems or contact the retailer where the
product was purchased. They can take this product for environmental safe recycling.
1.2 Storage
Your device has been carefully checked and packed before shipping. When unpacking it, make sure that all the
parts are included and keep the packaging away from children. We recommend that you keep the carton during the
warranty period, to keep your device perfectly protected in the event of repair or warranty.
1.3 Equipment Set-up
We recommend you consult a professional installer to set up your equipment. Otherwise, please follow the instructions
below:
 Refer to the user manual of your TV.
 Make sure that the HDMI cable is in a good condition.
 If you use TV SCART connection, use then well shielded SCART cable.
This manual provides complete instructions for installing and using this receiver. The following symbols will serve as
follow.
Warning Indicates warning information.
Tips Indicates any other additional important or helpful information.
MENU Represents a button on the remote control or the receiver. (Bold characters)
Move to Represents a menu item within a window. (Italic characters)
1.4 Accessories
 Installation Instructions
 Safety instructions/warranty cards
 Troubleshooting
 1 remote control unit
 2x batteries (AAA type)
WARNING The batteries should not be recharged, disassembled, electrically short-circuited, be mixed
or used with other types of batteries. If rechargeable accumulators instead of batteries are
going to be used (e.g. NiMH), we recommend using types with low self-discharge to ensure
long time operation of your remote control.
1.5 Usage of external USB devices
 It is recommended to use USB 2.0 storage devices or higher. If your device is not compatible to USB 2.0
specifications, recording, playback and other multimedia functions of the receiver might not work properly. *
 To ensure best performance of your USB storage device please format it via your receiver (through the menu
“Media Player”) to FAT32 system. Other file systems are not supported. However, it is possible to use already NTFS
formatted disks.
 We cannot guarantee compatibility with all types of USB storage devices.
 If you are going to use external USB HDDs (Hard Disk Drives), please consider that power specifications may
exceed the supported output of your receiver (max. 5 V/500 mA). If so, please connect your USB HDD to an
according external power adapter.
 It is advised not to store important information on USB storage devices used with the receiver. Always make
backups of data on your USB storage device before using it with this receiver. STRONG will not take responsibility
for any loss of information or circumstances caused by loss of information.
4

 We cannot guarantee the playback of all files although extensions are listed, as it depends on file size, codec, bit
rate and resolution.
*This user manual describes the full functionality including the recording function and may not be applicable if the software for recording via
USB has not yet been installed.
2.0 YOUR RECEIVER
2.1 DEFAULT PIN: 1234
2.2 Front Panel
Fig. 1
1. IR Sensor Receives commands from the remote control
2. LED Display Shows channel number in operation and time in standby
3. Mode Indicator LED RED indicates that the receiver is in STANDBY mode.
4. Standby/ON button Switches the receiver ON or into Standby
5. USB To connect your USB storage device.
2.3 Rear Panel
Fig. 2
1. CABLE IN Connect your receiver to the wall connector provided by the cable operator
2. CABLE OUT Connect your receiver to another digital receiver or to a TV to keep using its internal
(analogue) tuner (loop through function)
3. HDMI Connect your receiver with your TV set using an HDMI cable.
4. TV SCART Connect your receiver with your TV set using a SCART cable.
5. S/PDIF (coax.) Connect your receiver to a digital home theatre, AV receiver or digital audio
amplifier.
6. Power connector The receiver requires a wall adapter, mains voltage input 100~240 V AC 50~60Hz
12 V, 0.5 A DC output. Please check the local power conditions before connecting
the receiver to the mains supply.
2.4 Remote Control
Fig. 3
1. qSwitches the receiver On/Standby.
2. !Mutes all audio outputs of the receiver
3. 0~9 Enter channel number in TV mode or value input in menu
4. TV/R Toggles between TV or RADIO mode.
5. No function
6. FAV Opens the favourite group selection.
7. 9One step back in menu or switching between 2 last watched channels.
8. AUDIO Opens the audio language selection*
9. INFO Opens the current channel information; 2x opens the technical information about
the current channel.
10. EPG Opens the EPG (Electronic Programme Guide) in TV mode*
11. p/qChange channel to next/previous. Menu: Moves the cursor up/down.
12. tu Decreases/increases the volume level. Menu: Change settings for specific menus.
13. OK Opens the current channel list in menu: for confirmation
14. MENU Opens the main menu, in a menu you will get one step back.
15. Exits from the menu or sub-menu.
16. VOL+/VOL Increases/decreases the volume level.
17. P+/P Page up/down in all list modes.
18. LIST Opens the current channel list.
19. CH+/CH Channel up/down.
5
English

20. OPT No function.
21. TEXT Opens the Teletext if available*
22. SUB Opens a list of subtitles if available*
23. No function
24. 2Hold play during playback/starting Timeshift mode**
25. 5/6Fast rewind/fast forward.
26. 4Starts recording of the currently watched programme**
27. uIn multimedia menu for starting the playback
28. 78 Jumps to the previous/next file during playback
29. 3Stop playback.
30. COLOUR BUTTONS In different menus for specific functions
* Subtitles, Videotext, EPG (Electronic Programme Guide), and Audio languages are depending on availability in the specific broadcast
**This user manual describes the full functionality including the recording function and may not be applicable if the software for recording via
USB has not yet been installed.
2.5 Installing the batteries
Fig. 4
Open the cover on the remote control and insert 2x AAA batteries into the compartment. Correct position of the polar
diagram shows the batteries inside the compartment.
1. Open the cover.
2. Insert the batteries.
3. Close the lid.
WARNING The batteries should not be recharged, disassembled, electrically short-circuited, be mixed or
used with other types of batteries.
2.6 Using the remote control
Fig. 5
To use the remote control, point it towards the front of your receiver. The remote control supports a range of up to 5
meters distance to the receiver at an angle of up to approx. 30 degrees.
NOTE Managing the receiver will be limited or not possible if there are obstacles between the
remote control sensor (at the front panel of the receiver) and the remote control. Direct
sunlight or very bright light can reduce or disturb the reception of the remote control signals.
3.0 CONNECTION
Fig. 6
3.1 Connecting to cable TV
Connect your receiver to the wall connector provided by your cable operator, using a high quality coaxial cable (75
Ohms). Normally, wall connections could be either F-type or IEC male type. Use a cable with suitable connectors. This
receiver has an IEC female input.
3.2 Connecting to TV with HDMI cable
Fig. 6
The TV set shall be connected with the receiver using a good quality HDMI cable. This connection gives the highest
possible quality.
6

3.3 Connecting to TV with SCART cable
Fig. 6
Your receiver is also equipped with a SCART connector; alternatively, the TV set can be connected to the receiver using
a good quality SCART cable.
3.4 Connecting to a Digital Audio Amplier with S/PDIF
Fig. 6
By connecting your receiver to a digital amplifier or home theatre system, you can enjoy the best possible sound
quality and multi-channel audio (depending on the broadcast). Connect your Digital Audio Amplifier or home theatre
system with a suitable cinch cable to the S/PDIF connector on the back of the receiver.
3.5 Connecting to a Digital Audio Amplier and TV using HDMI
Fig. 7
By connecting your receiver to the latest digital amplifiers or Home Cinema systems you will enjoy the best possible
sound quality and multi-channel audio (depending on the broadcast). Connect the HDMI output of the receiver to an
input of your amplifier, and then connect the HDMI output of the amplifier to your TV set. Select the correct input on
your amplifier to watch and listen to programmes.
3.6 Connecting a USB storage device
Fig. 8
Connecting a USB device to the unit allows you to record TV programmes*, playback movies, music and picture files.
See chapter 7.5.1.
NOTE It is recommended to use USB 2.0 storage devices or higher for playback of recordings or HD
movies.
NOTE Timeshift/recording and playback only works properly when a fast USB storage device such
as a USB 2.0 HDD is connected to the receiver. Timeshift/recording and playback of HD
content requires a sufficient continuous read/write speed of the used USB storage device. *
*This user manual describes the full functionality including the recording function and may not be applicable if the software for recording via
USB has not yet been installed.
4.0 STARTING UP FOR THE FIRST TIME
When you use your receiver for the first time, the Welcome menu appears. Use p/qto move the highlight to the
setting you wish to alter and use tu to change values. Start by selecting your language using tu. Once you have
selected your language, press qto move the highlight to the next item and use tu to change.
Region: Select your region where this receiver is used.
Language Here you can choose your language.
Aspect Mode: Use this option to select the aspect ratio of your TV and the preferred conversion method.
The options are: Auto (automatic detection of aspect ratio), 4:3PS (Panscan) (Displays 16:9
widescreen broadcasts full screen on your 4:3 TV), 4:3LB (letterbox) (black bars on top and
under the picture on a 4:3 TV) and 16:9 (use this setting for 16:9 TV sets).
Subtitle Display: Select On to display subtitles per default. Select Hard of Hearing or Normal to show Hard of
Hearing or Normal subtitles per default. Select Off to hide subtitles per default.
Scan mode: Select All to store scrambled and free to air channels or select Free to store only free to air
channels. Note: Scrambled channels can’t be opened/watched with this receiver.
Provider: Select the “Provider” (Broadcaster, cable network) of your local cable system. If unknown, select
other. From the main menu Installation, more options are available to do different scan types.
When all settings have been made, move the highlight to Search and press OK to continue.
7
English

A search will be executed, this may take some time. A message will be show when finished.
NOTE Wrong region or provider selection can lead to missing channels or channels being stored at
wrong positions in the channel list. The search can be stopped anytime by pressing . From
the main menu Installation, more options are available to do different scan types. See chapter
4.1 DVB-C Installation.
TIP If the Welcome menu does not appear after switching on the receiver the first time, reset the
receiver to factory settings by pressing the MENU button and selecting Load Factory Setting
in the submenu Tools. DEFAULT PIN: 1234.
4.1 DVB-C Installation
Select Installation and press OK to enter the installation menu. Press p/qtu to select Channel Scan or Auto Scan.
Strength and Quality bars are available in each submenu, to provide information about signal presence. Network ID
(NID) and other technical data can be found on the website of your “Provider” (Broadcaster, cable network/your local
cable system) usually.
4.1.1 Channel Scan
Select Channel Scan and press OK to enter the Channel Scan menu. Press pq tuto set Scan mode, Channel No.,
Frequency, Symbol Rate, Scan QAM and Network Search. Highlight Search and press OK to start the channel scan. If you
are missing channels, we recommend to obtain technical data about the cable operator's base channel and start a
Network search from there to find all channels belonging to the network.
4.1.2 Auto Scan
Select Auto Scan and press OK to enter the Auto Scan menu. Press p/qtu to set Country and Network and then
highlight Search. Press OK to start the auto search.
Some operators in Germany are pre-installed.
4.1.3 Network ID scan
Select Network ID scan and press OK to enter the menu. Press pq tuto set Frequency, Symbol Rate, Scan QAM and
Network ID. Obtain technical data about your cable provider's base channel and Network ID from your provider and
start a Network ID scan from there to find all channels belonging to the network corresponding to the Network ID.
Highlight Search and press OK to start the search.
4.1.4 LCN
If LCN (Logical Channel Numbering) is activated and LCN is provided by the operator, channels will be stored in an
provider defined order. Set LCN to On to activate the provider defined channel numbering or Off to store channels
in the found order. This function only applies when a new channel search and only to Channel Scan and Auto Scan
options.
4.1.5 Free/All channels
If Free/All channels is set to Free, only channels will be stored that are signalled as Free-to-Air. Set to All to store all
channels found. This function only applies when a new channel search is performed and only to Channel Scan and
Auto Scan options. Note: Scrambled channels cannot be viewed with this receiver.
5.0 QUICK GUIDE TO USING YOUR RECEIVER
We at STRONG understand that you can’t wait to enjoy your digital HD cable receiver. The following quick guide will
make you familiar with the basic operation of this device. We do, however, advice you to read the full manual to get the
best performance from your receiver.
8

To turn your receiver ON or to Standby, use the qbutton on the remote control.
Choose a channel with the p/qbuttons. Alternatively, you can digit the channel number with the 0~9 buttons on
the remote control or press OK in viewing mode to display the channel list. The volume can be adjusted with the tu
buttons.
6.0 OPERATION
6.1 Changing channels
Following ways are possible for changing channels with your new receiver:
 Via direct access using the 0~9 buttons.
 Via the channel list using OK and the PG+/PG- buttons.
 Via the p/qbuttons.
6.1.1 Direct access via 0~9 buttons
To gain direct access to a certain channel, simply input its number with the 0~9 buttons on the remote control. Channel
numbers can be up to four digits long. Entering a number with less than four digits is possible. Just wait a few seconds
and your receiver will switch to the selected channel or press OK immediately after selecting the channel number.
6.1.2 Channel list
Press OK in viewing mode to display the Channel List. Use p/qin the channel list to highlight your channel of choice
and press OK once to select the highlighted channel. Press OK again to leave the channel list mode. Inside the channel
list it is possible to use the PG+/PG- buttons as well in order to scroll page-wise through the list.
TIP Use tu to toggle between the All Channel list and favourite list(s) or press FAV in viewing
mode for a list of the available favourite lists.
6.1.3 Using the p/qbuttons
pswitches to the next channel.
qswitches to the previous channel.
6.2 Info Banner
While watching TV you can press the INFO button at any time to access current information about the channel and
event*. Press INFO twice for technical details about the current channel.
*Event information is displayed when available. Availability depends on the broadcast.
6.3 Selection of audio language
Some channels support a choice of audio formats and/or languages. To select another audio stream, press AUDIO in
viewing mode. A list with available audio streams will be displayed. Use p/qto select a stream and confirm with OK.
The audio channel as stereo, mono, left and right can be selected with the tu buttons.
6.4 Teletext
Your receiver includes a fully featured Teletext. To access Teletext, press the TEXT button in viewing mode and use the
0~9 buttons to input the number of the page you wish to see. The coloured buttons of the remote control allow you to
jump to selected pages directly, as indicated on the bottom of the Teletext screen. Use the p/qbuttons to select one
page up or down, use the tu buttons to select subpages. Press or TEXT to get back to viewing mode.
9
English

6.5 Subtitles
Some channels support a choice of subtitle languages. Press SUB in viewing mode to display a list of available subtitle
languages. Select your subtitle of choice with p/qand press OK to confirm. Press to leave without making
changes.*
*Availability of DVB/HoH subtitles depends on the broadcast. If subtitles are not supported, they might be activated via Teletext if available.
6.6 Timeshift*
Timeshift allows you to pause live broadcasts and resume playback later. To activate this function set the Timeshift
mode in the DVR Set menu in HDD Information to Timeshift. For details, see 7.5.3. Press 2in viewing mode to activate
Timeshift. The progress information banner appears on screen. Live TV keeps playing for moment and will then pause.
Press uto resume time-shifted playback. Press 3to return to live TV.
NOTE Recording, Timeshift and its playback only work properly when a fast USB storage device
such as a USB 2.0 HDD is connected to the receiver. Recording, Timeshift and playback of HD
content require sufficient read/write speed of the used USB storage device.
*This user manual describes the full functionality including the recording function and may not be applicable if the software for recording via
USB has not yet been installed.
6.7 EPG (Electronic Programme Guide)
The Electronic Programme Guide is a very useful function that allows you to view event schedules and programme
information and to mark events/movies for recording. To access the EPG, press the EPG button in viewing mode. Use
p/qto select a channel and tu to select an event. Press OK to display detailed information of the selected event.
Use to quit the detailed information screen. Press RED to access further step functions. Use tu to select a step and
OK to execute it. Press to quit the step function. Press GREEN to set a timer for a selected event. Refer to section
7.3.4 for details of the timer function.
NOTE Availability of EPG data depends on the broadcast.
6.8 Instant Recording*
Your new receiver allows you to make an instant recording of the programme you are watching. Simply press 4to start
the recording. To enter the duration for the recording, press 4again. Use the 0~9 buttons to enter the recording time
and press OK to confirm.
At the beginning of recording an icon will be shown at the upper right corner of your TV screen. To stop the recording,
press 3then select Yes and press OK again. During recording it is possible to change to another channel as long as it is
broadcasted on same frequency.
*This user manual describes the full functionality including the recording function and may not be applicable if the software for recording via
USB has not yet been installed.
**Please connect a USB storage device with sufficient free space before you start a recording.
NOTE: Recording, Timeshift and its playback only work properly when a fast USB storage device
such as a USB 2.0 HDD is connected. Recording, Timeshift and playback of HD content
require sufficient read/write speed of the used USB storage device.
7.0 MAIN MENU
The main menu gives you access to settings, multimedia functions and games. To access the main menu, press MENU
in viewing mode. The main menu consists of the following sub menus: Edit Channel, Installation, System Setup, Tools and
Media Player.
10

Throughout the main menu, MENU or can be used to get back to the previous screen.
7.1 Edit Channel
Use p/qto select Edit Channel and press OK or uto enter.
Use p/qto highlight the submenu of choice and press OK to select.
Press or tto get back to the main menu.
7.1.1 TV Channel List
In the Edit Channel menu select TV Channel List with p/qand press OK to enter.
Use tu to change the channel group (if you have already set up favourite groups).
Select the channel of choice with p/q. Press OK to view the selected channel in the preview box.
7.1.1.1 Adding channels to favourite lists
Channels from the TV Channel List can be added to up to 8 different favourite groups. Press FAV in TV Channel List
to access this function. The FAV sign on the top of the screen will move up to indicate that the favourite function is
selected. Use p/qto select a channel you wish to add to a favourite group. When the highlight is on the channel of
your choice, press OK. A list with all available favourite lists will now pop up. Use p/qto select the favourite list you
wish to add the channel to and press OK, press to finalize the process. Favourite channels will be marked with a 
symbol. When all changes have been made, press twice. A confirmation banner will pop up. Select Yes to save the
changes or No to discard.
7.1.1.2 Locking channels
Locked channels can only be watched after entering the PIN code. DEFAULT PIN: 1234
To lock or unlock a channel, press RED while in TV Channel List. Press p/qto select a channel and press OK to lock
or unlock it. You are asked to input the PIN code. DEFAULT PIN: 1234 Locked channels will be marked with the 
symbol. Locking/unlocking multiple channels in one session is possible. When all changes have been made, press 
twice. A confirmation banner will pop up. Select Yes to save the changes or No to discard.
7.1.1.3 Skipping channels
Channels marked with Skip will be skipped when zapping channels with the p/qbuttons. The channels will still be
available from the channel list.
To mark channels for skipping, press GREEN while in TV Channel List. Use p/qto select a channel and press OK to
mark or unmark it for skipping. Channels set for skipping will be marked with the symbol. When all changes have
been made, press twice. A confirmation banner will pop up. Select Yes to save the changes or No to discard.
7.1.1.4 Moving channels
To enable the Move function, press YELLOW while in TV Channel List. Use p/qto select a channel and press OK to
select it. Now you can move the selected channel up or down inside the channel list by using p/q. When the channel
is on the position of your choice, press OK again. The channel is now fixed on its new position. When all changes have
been made, press twice. A confirmation banner will pop up. Select Yes to save the changes or No to discard.
7.1.1.5 Editing channels
The Edit function allows you to Sort, Rename or Delete channels. To enter the Edit menu, press BLUE while in TV Channel
List. The Edit Channel menu will appear.
If you made changes in the previous menu, but haven’t saved them yet, you will be asked to do so now.
Sort
Press RED to enter the Sort menu.
Use p/qto select sorting method and press OK to confirm.
Possible methods are:
Name (A-Z): Sorting in alphabetical order from A to Z.
Name (Z-A): Sorting in alphabetical order from Z to A.
11
English

Free/Scramble: First in the list will be Free-To-Air channels.
Lock: All unlocked channels will placed first in the list.
Rename
Press GREEN in Edit Channel to enable the Rename function. The Rename sign will move up to indicate that Rename
is selected. Use p/qto highlight a channel and press OK to select it. A text field will now pop up at the right of the
screen. Use tu p/qto select characters and enter them with OK. When you have finished editing, press YELLOW to
enter the changes. When all changes have been made, press twice. Select Yes to save the changes or No to discard.
Delete
Press BLUE in Edit Channel to enable the Delete function. The Delete sign will move up to indicate that Delete is selected.
Use p/qto highlight a channel and press OK to mark it for deletion. When you have marked all channels you wish
to delete, press twice. A confirmation banner will be displayed. Select Yes to delete the marked channels or No to
cancel.
7.1.2 Radio Channel List
Basically, the operation of the Radio Channel List is the same as in the TV Channel List. The only difference is that in Radio
Channel List there is no video information, so it will always display the background on the preview screen.
7.1.3 Delete all
Use this menu to delete all stored channels. Select Delete All with p/qand press OK. The receiver asks you to enter the
pin code. (DEFAULT PIN: 1234). Inside the confirmation window select Yes with tu and press OK to delete or select
No to cancel.
Warning! The Delete all function will permanently delete all current channels and all favourite lists from
your receiver, and you are not able to leave the menu until you search for channels again.
7.1.4 Rename Favourite list
This menu allows you to personalize the names of the 8 available favourite lists.
Use p/qto select Rename Favourite List from the Edit Channel Menu and press OK to proceed. The names of all groups
are now displayed. Select a favourite group with p/qand press OK to edit its name. A text field will now pop up at the
right of the screen. Use tu p/qto select characters and enter them with OK. When you have finished editing, press
BLUE to save the changes. When all changes have been made, press twice to leave this menu.
7.2 Installation
7.2.1 Channel Scan
Use p/qto select Installation, press OK or uto advance.
Use p/qto select Channel Scan and press OK to enter.
Use tu to toggle between available scan modes: By Channel and By Frequency.
If By Channel is selected, use p/qtu to select Channel No Symbol Rate and Scan QAM. If Network Search is set to On, all
channel belonging to the network of your operator will be found, according to NIT information provided in the signal
of the operator.
If By Frequency is selected, use p/qtu and 0 ~ 9 to select Frequency, Symbol Rate and select the correct Scan QAM
parameter. Highlight Search and press OK to start scanning. Newly found channels will be added to the channel list.
If Network Search is set to On, all channel belonging to the network of your operator will be found, according to NIT
information provided in the signal of the operator.
NOTE: Network ID (NID) and other technical data can be found on the website of your “Provider”
(Broadcaster, cable network/your local cable system) usually. Start a Network search from
there to find all channels belonging to the network.
12

7.2.2 Auto Scan
Use p/qto select Installation and press OK or uto advance.
Select Auto Scan with p/qand press OK to enter.
Select your country and network.
Use p/qto highlight Search. Now press OK to start auto scan.
The receiver will store all found channels in the channel list.
NOTE: Network ID (NID) and other technical data can be found on the website of your “Provider”
(Broadcaster, cable network/your local cable system) usually. Start a Network search from
there to find all channels belonging to the network.
7.2.3 Network ID scan
Select Network ID scan and press OK to enter the Network ID scan menu. Press pq tuto set Frequency, Symbol Rate,
Scan QAM and Network ID. Obtain technical data about your cable provider's base channel and Network ID from your
provider and start a Network ID scan from there to find all channels belonging to the network corresponding to the
Network ID. Highlight Search and press OK to start the search. Network ID (NID) and other technical data can be found
on the website of your “Provider” (Broadcaster, cable network/your local cable system) usually. Start a Network search
from there to find all channels belonging to the network.
7.2.4 LCN (Logical Channel Numbering)
If LCN (Logical Channel Numbering) is activated and an LCN signal is provided by the provider, channels will be stored
in a provider defined order. Set LCN to On to activate provider defined channel numbering or Off to store channels in
found order. This function only applies when a new channel search is performed.
7.2.5 Free/All channels.
If Free is selected, only “Free-to-air” channels are stored.
If [All} is selected, scrambled channels will also be stored.
NOTE: Only Free channels can be watched with this unit.
7.3 System Setup
This menu allows you to manage the system settings of your receiver. It consists of the following sub-menus: Language,
TV System, Local Time Setting, Timer Setting, Parental Lock, OSD Setting, Audio Description Setting and Auto Standby.
Press p/qto highlight the menu of choice and press OK advance to the next screen. Use p/qto move the highlight
to the setting of choice. Values can be changed with tu. Press to leave.
7.3.1 Language
This menu allows you to set up your language preferences.
Language: Use tu to select the language for the On Screen Display.
First Audio: Use tu to select Audio language.
Second Audio: Use tu to select a language that will be played when the language selected at First Audio isn’t
available.
Subtitle Display: Use tu to select the use of subtitle Normal, Hard of Hearing or Off.
Subtitle Language : Use tu to select the preferred subtitle language.
2nd Subtitle Language: Use tu to select the preferred 2nd subtitle language if the 1st preference is not available.
Teletext: Use tu to select the preferred Teletext language (when available).
*Availability of DVB/Hard of Hearing subtitles depends on the broadcast. If subtitles are not supported, they might be activated via Teletext if
available.
13
English

7.3.2 TV System
Use this menu to match your receiver to your TV set. The following settings are available:
Video Resolution: Use this option to select the video resolution of your TV screen. The options are: By Source
(automatic detection of video resolution offered to the receiver), By Native TV (automatic
detection of maximal resolution of TV screen), and manual selections 480i, 576i up to 1080p.
Please use a setting that matches the specifications of your TV. After a selection is made, you
will be asked to confirm. Selection above 576i is only applicable on HDMI output.
Aspect Mode: Use this option to select the aspect ratio of your TV and the preferred conversion method.
The options are: Auto (automatic detection of aspect ratio), 4:3PS (Panscan) (Displays 16:9
widescreen broadcasts full screen on your 4:3 TV), 4:3LB (letterbox) (black bars on top and
under the picture on a 4:3 TV) and 16:9 (use this setting for 16:9 TV sets).
Digital Audio Output: Toggles between PCM and Bitstream output. When PCM is selected, all digital audio will be
converted to stereo audio. Bitstream enables you to listen or transfer Dolby® Digital/Dolby®
Digital Plus* audio to the TV via HDMI or to a Home entertainment system (for example)
through coaxial S/PDIF.
NOTE: Dolby® Digital Plus* is only available on the HDMI output.
*Dolby and the double-D symbol are registered trademarks of Dolby Laboratories
7.3.3 Local Time Setting
Here you can set up your region and time zone.
Region: Use tu to select the region you live in.
GMT Usage: Set to By Region for broadcaster defined time, User Define to select manual a GMT zone or to Off
to input time and date manually.
GMT Offset: Allows you to adjust your time zone. This option is only available when GMT Usage is set to User
Define.The GMT Offset range is "-11:30 ~ +12:00", increasing by half hours progressively. The
cities matching the set GMT Offset are displayed at the bottom of the screen.
Summer time: Select On to add one hour for summer time.
Date: Date and Time settings are available only when GMT Usage is set to Off. Use the 0~9 buttons to
enter the date. Press to proceed.
Time: Date and Time settings are available only when GMT Usage is set to Off. Use the 0~9 buttons to
enter the time. Press to proceed.
7.3.4 Timer Setting
This menu allows you to set up to 8 timed events for recording or waking up the receiver.
Use pq to select Timer Setting from the System Setup menu and press OK to enter.
The receiver will display a list with 8 timers, followed by their respective status. Select the timer you wish to set with
pq and press OK to proceed.
The timer setup menu will now be displayed.
The following settings are available:
Timer Mode: Choose between Off the timer is inactive, Once, Daily (the timer will be executed every day,
same time) or Weekly (the timer will be executed every week, same day, same time) and
Monthly (the timer will be executed every month, same day, same time).
Timer Service: Choose between Channel (the timer will wake up the receiver) or Record (Timer will start
recording the scheduled event).
Wakeup Channel: Use tuor OK to call up channel list, therein use pq or P+/P and press OK again to select
the channel the timer should switch to or record on.
Wakeup Date: Use the 0~9 buttons to enter the date for the timed event.
On time: Use the 0~9 buttons to enter the starting time.
Duration: Use the 0~9 buttons to enter the duration of the timer.
14

When all settings have been made, use pq to highlight Save and press OK to confirm. To quit the timer without
saving your settings, highlight Cancel.
7.3.5 Parental Lock
This menu allows you to protect the installation menu and/or channels with a PIN code. You can also enter a new PIN
code in the Parental Lock menu.
Use p/qto select Parental Lock from the System Setup menu and press OK to proceed. You will be asked to enter your
PIN code. (DEFAULT PIN: 1234)
Menu Lock: Locks the installation menu. You can set Menu Lock to On or Off.
Parental Rating: Choose between: Off, 10 years and up to 18 years. Channels with a parental rating above the
chosen age will be protected with a PIN code (if rating is available in your local broadcast).
New Password: Enter your new PIN code (4 digits) here.
Confirm Password: Re-enter your PIN code here to confirm.
7.3.6 OSD Setting
This menu allows you to change settings for: OSD Timeout and OSD Transparency.
OSD Timeout: Sets the duration time of on screen banners and messages remove. The range is 1~10 seconds
or Always On.
OSD Transparency: To set the OSD transparency from Off ~ 40% with 10% steps.
7.3.7 Audio Description
Audio Description is a service, which some broadcasters are supporting to describe the content on screen for the
visually impaired people. Select AD Service On and Use AD as default also On to activate the service. With AD Volume
Offset the level of the AD text can be adjusted.
NOTE Availability of Audio Description depends on the broadcast.
7.3.8 Auto Standby
Auto Standby is a new feature that helps you reducing power consumption. When set to 3, 4 or 5 hours, the receiver
will switch to standby if it doesn’t receive any commands during this time. Set Auto Standby to Off to deactivate the
automatic standby function.
Default is 3 hours.
7.4 Tools
Press MENU in viewing mode to enter the Main Menu.
Select the Tools submenu with p/qand press OK or uto enter.
Use p/qto highlight the submenu of choice and press OK proceed.
Press to leave.
7.4.1 Information
This submenu shows receiver specific information such as hardware version and software version. Please open the
Information screen when you call our hotline. The person who answers your call might ask for the information given in
this screen.
7.4.2 Load Factory Settings
This option allows you to reset the receiver to factory settings, which clear all stored channels.
Warning! By resetting your receiver to factory default, all your settings and stored channels will be
permanently deleted. Please use this option with care.
15
English

Use p/qto select Load Factory Settings in the Tools menu and press OK. You are asked to input your PIN code.
Input the correct PIN code using the 0~9 (DEFAULT PIN: 1234). A confirmation window is displayed.
Select Yes to return to factory settings.
The receiver will return to its initial state and show the Welcome page.
Select No to cancel.
Press to leave.
7.4.3 Upgrade by USB
This feature allows you to upgrade receiver software via the USB port. When new software is available for your receiver,
it can be downloaded from our website www.strong.tv.
Place the software file (unzipped) in the root directory of your USB storage device (HDD, memory stick etc.) and connect
the device to the USB port of the receiver.
Select Upgrade by USB from the Tools menu and press OK to proceed.
The upgrade menu will now be displayed.
Use p/qto select Upgrade Mode and choose option Allcode.
Use p/qto select Upgrade File and choose the file containing the latest and correct software.
When all settings have been made, move the highlight to Start and press OK to start the upgrade process. The receiver
will show a warning message.
Select Yes to finalize the upgrade or No to quit without upgrading.
NOTE: If, after a software upgrade, the receiver should behave in an unexpected way, please
perform a factory reset as well. See chapter 7.4.2.
Warning! Be sure to have the correct software update for your brand and model available. Trying to
update to any other software may damage the unit and will void the warranty. After an
update the receiver restarts automatically. During the upgrade process NEVER disconnect the
receiver from the mains or switch off the power! Doing so might damage your receiver and
will void warranty!
Channel Dump and Load function
This feature allows you to load a channels list quickly and use a channel list that previously was created on this (backup)
or another receiver from the same model via the USB port.
This is useful when more receivers have to be installed on the same network, thus omitting a full scan and (optional)
sorting of channels. It is also useful as a backup for your own unit.
Channel Dump function (backup to USB)
Have a storage device connected to the USB port of the receiver. Select Upgrade by USB from the Tools menu and press
OK to proceed. The upgrade menu will now be displayed.
Use pq to select Upgrade Mode and choose the option Dump channel list.
A DataBase file name containing date and time will be presented, format DBMMHHDDMMYYYY
(DatebaseMinuteHourDayMonthYear.udf).
Use pq to select Start and press OK to proceed. The channel list and favourites will be saved.
Update Channel list function (load from USB)
Have the storage device connected to the USB port of the receiver, containing a previously made channel list on this
unit or another of the same model. Select Upgrade by USB from the Tools menu and press OK to proceed. The upgrade
menu will now be displayed.
Use pq to select Upgrade Mode and choose the option Update Channel list.
Use pq to select Upgrade File. Select the correct database file name, format DBMMHHDDMMYYYY
(DatebaseMinuteHourDayMonthYear.udf).
Use pq to select Start and press OK to proceed. Confirm the upgrade with OK to proceed.
16