Strong SRT 2022 User manual

User Manual
Bedienungsanleitung
Manuel d'u lisa on
Manuale d'uso
Manual del Usuario
Manual do U lizador
Bruksanvisning
Instrukcja obsługi
Návod k obsluze
Používateľská príručka
Használa útmutató
Посібник користувача
Ръководство за употреба
Руководство пользователя
Android IP Box
SRT 2022
Picture similar
user-friendly and
easy to handle
video
streaming
share
contents
video
phone calls
Version 7.1

13 Apr 2018 15:50
Supplied by STRONG Austria
Represented by
STRONG Ges.m.b.H.
Franz-Josefs-Kai 1
1010 Vienna
Austria
Email: [email protected]

LICENSES
THIS PRODUCT IS LICENSED UNDER THE AVC PATENT PORTFOLIO LICENSE FOR THE
PERSONAL AND NONCOMMERCIAL USE OF A CONSUMERTO (i) ENCODE VIDEO IN
COMPLIANCE WITH THE AVC STANDARD (“AVC VIDEO”) AND/OR (ii) DECODE AVC VIDEO
THAT WAS ENCODED BY A CONSUMER ENGAGED IN A PERSONAL AND NON-
COMMERCIAL ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED TO
PROVIDE AVC VIDEO. NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER
USE. ADDITIONAL INFORMATION MAY BE OBTAINED FROM MPEG LA, L.L.C. SEE
HTTP://WWW.MPEGLA.COM
This product contains one or more programs protected under international and U.S. copyright
laws as unpublished works. They are condential and proprietary to Dolby® Laboratories. Their
reproduction or disclosure, in whole or in part, or the production of derivative works therefrom
without the express permission of Dolby® Laboratories is prohibited. Copyright 2003-2009 by Dolby®
Laboratories. All rights reserved.
THIS PRODUCT IS SOLD WITH A LIMITED LICENSE AND IS AUTHORIZED TO BE USED ONLY
IN CONNECTION WITH HEVC CONTENTTHAT MEETS EACH OFTHE THREE FOLLOWING
QUALIFICATIONS: (1) HEVC CONTENT ONLY FOR PERSONAL USE; (2) HEVC CONTENT THAT IS NOT
OFFERED FOR SALE; AND (3) HEVC CONTENT THAT IS CREATED BY THE OWNER OFTHE PRODUCT.
THIS PRODUCT MAY NOT BE USED IN CONNECTION WITH HEVC ENCODED CONTENT CREATED BY A
THIRD PARTY, WHICH THE USER HAS ORDERED OR PURCHASED FROM A THIRD PARTY, UNLESS THE
USER IS SEPARATELY GRANTED RIGHTS TO USE THE PRODUCT WITH SUCH CONTENT BY A LICENSED
SELLER OF THE CONTENT. YOUR USE OF THIS PRODUCT IN CONNECTION WITH HEVC ENCODED
CONTENT IS DEEMED ACCEPTANCE OFTHE LIMITED AUTHORITY TO USE AS NOTED ABOVE.
13 Apr 2018 15:53
1

TABLE OF CONTENTS
1.0 INTRODUCTION 3
1.1 Safety Instructions 3
1.2 Equipment Set-up 4
1.3 Accessories 5
1.4 Usage of external USB devices 5
2.0 YOUR IP BOX 5
2.1 DEFAULT PIN: 1234 5
2.2 Front Panel 5
2.3 Rear Panel 6
2.4 Side Panel 6
2.5 Remote control 6
2.6 Installing the batteries 7
2.7 Using the remote control and USB
adapter 7
3.0 CONNECTIONS 8
3.1 Basic connection 8
3.2 Connecting to the Internet 8
3.3 Connecting to a Digital Audio Amplier 8
3.4 Connection of a wireless mouse or key
board* 8
3.5 Connection of a USB web camera* 9
4.0 FIRST INSTALLATION 9
5.0 HOW TO USE THE ANDROID PLATFORM 10
5.1 Connect to wireless networks 10
5.2 Open the browser 11
5.3 Picture gallery 11
5.4 Video player 11
5.5 Music library 11
5.6 File Manager 11
5.7 S link for streaming from other devices 12
5.8 The Store 12
5.9 Applications 12
5.10 Open all applications 13
6.0 SETTING OF SYSTEM 13
6.1 Network 13
6.2 Add accessory (Bluetooth) 14
6.3 Display 14
6.4 Sounds 14
6.5 Language 14
6.6 Storage & Reset 14
6.7 Info (About) 15
6.8 More Settings 16
6.9 HDMI CEC 16
7.0 TROUBLESHOOTING 16
8.0 TECHNICAL SPECIFICATIONS 17
STRONG declares that this item complies with the basic requirements and other relevant regulations of directives
RED 2015/53/EU, EMC 2014/30/EU, LVD 2014/35/EU and RoHS 2011/65/EU
Subject to alterations. In consequence of continuous research and development technical specications, design and
appearance of products may change. Android and Google Wallet are trademarks of Google Inc. Wi-Fi is a registered
trademark of Wi-Fi Alliance®. Skype is a trade mark of Skype and STRONG is not aliated, sponsored, authorised or
otherwise associated by/with the Skype group of companies. HDMI, the HDMI logo and High-Denition Multimedia
Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.
Manufactured under licence from Dolby Laboratories. Dolby Audio and the double-D symbol are registered trademarks of
Dolby Laboratories. All other product names are trademarks or registered trademarks of their respective owners.
© STRONG 2017. All rights reserved.
2

1.0 INTRODUCTION
Thank you for choosing the Android IP Box from STRONG. It has been produced with the latest new
technology and oers extensive entertainment and great versatility. We wish you many hours of new
great experiences exploring the Android world!
1.1 Safety Instructions
Read all of the instructions before operating the device. Keep these instructions well for later use.
˚Only use attachments/accessories specied or provided by the manufacturer (such as the
exclusive supply adapter, battery etc.).
˚Please refer to the information on the product enclosure for electrical and safety information
before installing or operating the apparatus.
˚To reduce the risk of re or electric shock, do not expose this apparatus to rain or moisture.
˚The ventilation should not be impeded by covering the ventilation openings with items, such
as newspaper, table-cloths, curtains, etc.
˚The apparatus shall not be exposed to dripping or splashing and no objects lled with liquids,
such as vases, shall be placed on the apparatus.
˚This mark indicates a risk of electric shock.
˚To prevent injury, this apparatus must be securely attached to the oor/wall in accordance with
the installation instructions.
˚Danger of explosion if the battery is incorrectly replaced. Replace only with the same or
equivalent types.
˚The battery (battery or batteries or battery pack) shall not be exposed to excessive heat such as
sunshine, re or the like.
˚Excessive sound pressure from earphones and headphones can cause hearing loss.
Listening to music at high volume levels and for extended durations can damage one's hearing.
˚In order to reduce the risk of damage to hearing, one should lower the volume to a safe,
comfortable level, and reduce the amount of time listening at high levels.
˚The mains plug or appliance coupler is used as disconnect device, it shall remain readily
operable. When not in use and during movement, please take care of the power cord set, e.g. tie
up the power cord set with cable tie or something like that. It shall be free from sharp edges or
similar which can cause abrasion of the power cord set.When put into use again, please make
sure the power cord is not damaged. The absence of a light indication on the apparatus does
not mean that it is fully disconnected from the mains. To disconnect the apparatus completely,
the mains plug must be pulled out.
˚Attention should be drawn to environmental aspects of battery disposal.
˚No naked ame sources, such as lighted candles, should be placed on the apparatus.
˚To prevent the spread of re, keep candles or other open ames away from this
product at all times.
˚Equipment with this symbol is a Class II or double insulated electrical appliance. It has
been designed in such a way that it does not require a safety connection to electrical
earth.
3

Precautions
˚Never try to open the device. It is dangerous to touch the inside of the device due to high
voltages and possible electrical hazards. Opening the device will void the warranty of the
product. Refer all maintenance or servicing to suitably qualied personnel.
˚When you are connecting cables, be sure that the device is disconnected from the mains
supply voltage. Wait a few seconds after switching o the device before you move the device or
disconnect any equipment.
˚It is a necessity that you only use an approved extension and compatible wiring that is suitable
for the electrical power consumption of the installed equipment. Please ensure that the
electrical power supply corresponds with the voltage on the electrical identication plate at the
back of the device.
Operating Environment
˚Do not install this equipment in a conned space such as a bookcase or similar unit.
˚Do not use the set near damp, and cold areas, protect the set from overheating.
˚Keep away from direct sunlight.
˚Do not use the set near dust place.
˚Do not place candles near the opening area, to avoid ammable foreign material from entering
the device.
WEEE Directive
Correct Disposal of this product. This marking indicates that this product should not be
disposed with other household wastes throughout the EU. To prevent possible harm to
the environment or human health from uncontrolled waste disposal, recycle it
responsibly to promote the sustainable reuse of material resources.To return your used
device, please use the return and collection systems or contact the retailer where the
product was purchased. They can take this product for environmental safe recycling.
Storage
Your device has been carefully checked and packed before shipping. When unpacking it, make sure
that all the parts are included and keep the packaging away from children. We recommend that you
keep the carton during the warranty period, to keep your device perfectly protected in the event of
repair or warranty.
1.2 Equipment Set-up
Please follow the instructions below:
˚Use a high quality, well shielded HDMI cable to watch also in highest screen resolutions.
This user manual provides complete instructions for installing and using this IP Box. The symbols will
serve as follows:
Warning Indicates warning information.
Tips Indicates any other additional important or helpful information.
MENU Represents a button on the remote control or the IP Box. (Bold characters)
Move to Represents a menu item within a window. (Italic characters)
4

1.3 Accessories
˚Installation Instructions
˚1 Remote control
˚1 USB adapter for the remote control
˚2x batteries (AAA type)
˚HDMI cable
˚Power adapter (5 V 2 A, max. 10 W)
Warning: The batteries should not be recharged, disassembled, electrically short-
circuited, be mixed or used with other types of batteries.
NOTE: For the appropriate usage with this device, use only power adapters as
listed below (in case of a necessary exchange):
˚Model: ASM-0502000; Manufacturer: Shenzhen Aosimai TechnologyCo.Ltd
The usage of other power adapters may cause damage to the device. Such
damage is not covered under warranty.
1.4 Usage of external USB devices
˚It is recommended to use USB 2.0 storage devices or higher. If your device is not compatible to
USB 2.0 specications, playback and other functions of the IP Box might not work properly.
˚STRONG cannot guarantee compatibility with all types of USB devices such as web cams,
keyboards, mouse devices, storage devices.
˚STRONG cannot guarantee perfect operation when a HDD and a web cam are used at the same
time.
˚If you are going to use external USB HDDs (Hard Disk Drives), please consider that power
specications may exceed the supported output of your box (max. 5 V/500 mA). If so, please
connect your USB HDD to an external power adapter.
˚It is advised not to store important information on USB storage devices used with the box.
Always make backups of data on your USB storage device before using it with this box.
STRONG will not take responsibility for any loss of information or circumstances caused by loss
of information.
2.0 YOUR IP BOX
2.1 DEFAULT PIN: 1234
2.2 Front Panel
Fig. 1
1. Status indicator: Indicates status of ON or OFF modes.
2. IR sensor: Receives Standby/On signal from the remote control.
5

2.3 Rear Panel
Fig. 2
1. AV To connect your IP Box to an audio amplier.
2. LAN To connect to your router with a RJ 45 network cable.
3. HDMI To connect your IP Box to your TV via HDMI cable.
4. Power To connect the included power adapter of 5 V.
2.4 Side Panel
Fig. 3
1. Micro SD card slot To insert an optional Micro SD card.
2. USB: To connect USB devices like: mouse/keyboard/storage devices
2.5 Remote control
Fig. 4
1. qTurns the IP Box ON/Standby
2. !Turns the sound on or o.
3. ASPECT No function
4. FAV No function
5. TV/RADIO No function
6. COLOUR BUTTONS Dierent functions in menu mode
7. Opens selection of wall papers
8. Returns to the Android menu
9. Returns to the previous menu or exits the App
10. pq Moves the highlight up/down in the menu
11. tu Navigates through the menus or changes values of settings in a
menu
12. OK Conrms a selection
13. VOL+/VOL- Increases/decreases the volume level
14. PG+/PG- Switches to the next/previous pages
15. Switches to recently watched apps
16. Turns the air mouse function ON or OFF.
17. 0-9 Numeric value input
18. No function
19. EPG No function
20. SUB No function
21. 4No function
22. TXT No function
23. AUDIO No function
24. 7Jumps to the previous le during playback.
25. 12 Starts/resumes playback
26. 3Stops playback of les
27. 8Jumps to the next le during playback.
28. Standard QWERTY keyboard
6

2.6 Installing the batteries
Fig. 5
Open the cover on the remote control and insert 2x AAA batteries into the compartment.
The correct position of batteries polar diagram is shown inside the batteries compartment.
1. Open the cover.
2. Insert the batteries.
3. Close the lid.
Warning: The batteries should not be recharged, disassembled, electrically short-
circuited, be mixed or used with other types of batteries.
2.7 Using the remote control and USB adapter
Fig. 6
Please rst insert the USB adapter of the remote control in a free USB port. This USB adapter receives
the RF (radio controlled) signals from remote control. Without this adapter only the Standby button
will work via the IR sensor (infrared). The remote control has an in-built“G-sensor” which is used as
pointer on your screen in the Android mode. This is called as “Air mouse”function and allows you to
move the pointer by moving the remote control through the air.
Note: As this function uses more power as normal pressing of buttons we
recommend using Alkaline batteries to ensure longer operation time
of your remote control. When the batteries are almost empty the LED
indication on the remote control will start blinking for 15 seconds after you
press any button.
Under normal conditions your remote control has been paired with the USB adapter in the factory
and therefore the“Air mouse”function of your remote control will directly work for your IP box. In
case you can only use the qbutton on the remote control and none of the other buttons have a
function, or in case the red LED on the remote control keeps blinking, it could be that the pairing
between the remote control and the USB adapter is not correct.
In that case you need to pair the USB adapter to the remote control manually:
1. Remove the USB adapter from the USB slot on the IP box.
2. Make sure the IP box is switched ON.
3. Remove the batteries from the remote control and insert them again. The LED on the remote
control starts ashing.
4. Press and hold the OK and buttons at the same time for a few seconds. The LED on the
remote control ashes more quickly.
5. Insert the USB adapter into a free USB port of the box and wait until the LED on the remote
control stops ashing (g. 6).
6. Now the remote control is paired with the USB adapter.
7

NOTE: The function of Standby on the remote control is limited or not possible if
there are obstacles in front of the remote control sensor on the front panel
of the IP Box. If only the Standby button is working and there is no reaction
when pressing any other button it could be that the batteries are empty
or the USB adapter was removed or, as mentioned above, you need to pair
the USB adapter to the remote control manually.
3.0 CONNECTIONS
3.1 Basic connection
Fig. 7
a. Connect one end of a good quality HDMI cable to the HDMI output on your IP Box and the
other end to the HDMI input of your TV.
b. Connect the LAN cable from your router/Internet connection into the RJ45 LAN input.
c. Plug in the power plug from the 5 V adapter and insert the adapter into a suitable wall outlet.
3.2 Connecting to the Internet
Fig. 7
a. For the best performance we advise using a wired connection to your router.
b. Alternatively, you can use the in-built wireless adapter to connect to the Internet via your
wireless router.
Note: Be aware that the Internet speed will be reduced by walls or long distance
between the IP Box and the router when using wireless connection. This
will lead to lower quality of video streams from the Internet.
3.3 Connecting to a Digital Audio Amplier
Fig. 7
Use the HDMI output to connect your IP Box to the HDMI input of your Hi-Fi system or audio amplier
and connect the HDMI output from your Hi-Fi system to the HDMI input of your TV. In the Android
sounds menu, you can select the Digital sounds option to activate Dolby digital audio by selecting
HDMI or select PCM for downmix to stereo audio.
3.4 Connection of a wireless mouse or key board*
Fig. 8
For optimal usage of the Android part we recommend using also a mouse or wireless mouse for
maximum freedom, besides the remote control. This enables tracking and dropping of functions, just
as you can do on mobile phones.
Switch the main power O and insert a mouse or wireless mouse dongle into one of the free USB
slots. Switch the main power back On. The device will be automatically recognised and you can start
using it.
8

In the same way you can use a keyboard.* It will make typing of information (web addresses,
searching) much more convenient.
*Not included in the packaging.
3.5 Connection of a USB web camera*
Fig. 8
If you like to take pictures or talk to other people and watch with video conference apps as SkypeTM,
you can connect a USB web camera with an in-built microphone to your Android IP Box.
Download and install the latest new video app from the Store rst. Then switch the main power O
and insert the USB webcam connector into one of the free USB slots. Switch the main power back On.
The webcam will be automatically recognised and you can start using it.
*Not included in the packaging.
Note: Please check on our web site www.strong.tv for the supported webcam
models.
If you like to change the login name, camera model or if you don’t get the webcam running, enter
“Settings – Apps – Skype -- Clear data”rst and then login to SkypeTM to test a video call and if the
new login works.
4.0 FIRST INSTALLATION
This procedure will enable you to enjoy and setup your Android IP Box just with a few steps. It is
recommended to follow the First Installation step by step. It will guide you through the basic
installation.
Step 1: Language Select your preferred language for the on screen menu. Use tu to change
language and press OK to conrm your selection.
Step 2: Resolution Select the screen resolution you prefer. Default selection is Automatic, which
already shows the best setting of the connected screen. Press OK to conrm
your selection and the IP Box will follow. A banner appears to conrm the
new setting by selecting OK.Conrm again with OK. If you do not see this
banner immediately, wait a couple of seconds and the screen will return to its
previous state. Then try another resolution.
Step 3: Screen Size Use pq to adjust the size of the screen so it exactly ts the screen you are
using. Press OK to conrm.
Step 4: Network If you have already connected the Ethernet cable to your router, in most
cases the unit nds the correct settings automatically and jumps directly
to Step 5. If you haven’t connected a Ethernet cable, but prefer using Wi-Fi,
select Wi-Fi and press OK to open the menu with the available wireless
networks. Use pq to select your network and enter the key or password.
The 0 ~ 9 buttons on the remote control can also be used for entering.
Step 5: Date&Time: If you have successfully connected to the Internet in Step 4, this screen will
automatically show the date and your local time. If necessary you can select
an item to modify it manually.
9

Step 6: Final step: Select Login to Google Play Store to set up a Google account. Select Home
page to skip this step, go directly to the Android main page and set up your
Google account later.
After the above steps have been made the IP Box will go into operating mode and show the home
screen. Now you can use and enjoy it!
5.0 HOW TO USE THE ANDROID PLATFORM
This chapter describes how to use the Android platform. After turning on your IP Box, Home opens.
The app icons you keep in the tray remain visible on every Home screen. All app icons in the centre
are permanent. Press to see all your apps and widgets. The middle of your Home screen can hold
app and widget icons as well as folders.To open an app, folder or widget, click on its icon.
5.1 Connect to wireless networks
To fully use the Android platform you rst need to setup connection to the Internet. If you missed
this setup in Step 4 of the First Installation you can setup this connection by selecting Settings from
the Home screen and press OK. Select Network and press OK again. In this menu you can setup if
you want to connect via Wi-Fi or Ethernet (LAN cable). Press OK to conrm and to open and select
your network. Enter and store your passwords or gateway ports here. Passwords and IP settings
are provided by your Internet provider (or in-house router). A message appears to inform about a
successfully made setup. Press until you return to the Home screen.
When all settings have been installed, select Browser and press OK access the Internet.
Turn your wireless on and connect it to a wireless network
If a wireless network has been added during the rst time installation, Wi-Fi is turned on
automatically.
1. Click the settings icon Setting on the Home or All Apps screen.
2. Click the icon More and then choose Wi-Fi.
Slide the Wi-Fi switch to the On position.The device scans for available wireless networks and displays
the names of those it nds. Secured networks are indicated with . If the device nds a network that
you have connected to previously, it connects to it.
3. Click a network name to see more details or connect to it. If the network is secured, you will be
prompted to enter a password or other credentials. (Ask your network administrator for details.)
To modify the settings of a network, click and hold the network name.
Forget a wireless network
You can make the device forget about the details of a wireless network that you have added, if you
don’t want your device to connect to it automatically or if it is a network that you use no longer.
1. Turn on Wi-Fi if it is not already on.
2. In the Wi-Fi settings screen, click on the name of the network.
3. Click Forget in the dialogue that opens.
When you connect to a wireless network, the USB device obtains a network address and other
information it needs from the network, using the DHCP protocol.
10

5.2 Open the browser
Click on the Browser icon at the bottom of the Home screen or on the Application icon in the launcher.
The browser also opens when you click on a web link in an email or text message. Use pqtu
to select an item, menu or web address search bar to enter a website address (URL) of your wish.
Alternatively you can press on the button to simulate pqtu with the mouse function. Press OK
to conrm or to go one step back. You can press this button more times until you to return to the
Home screen.
5.3 Picture gallery
Click on the Pictures icon in the launcher or on the Home screen. The gallery presents pictures stored
on your Micro SD card or USB storage device including pictures which have been downloaded from
the web or other locations or that are stored in web albums. You can also edit the pictures on your
USB device and share them with friends. Press to stop until you to return to the Home screen.
5.3.1 View and browse pictures
1. Open an album in the Gallery with a mouse click or press OK on one of the folders/pictures.
2. The folder gallery opens and on top of this screen you can select the picture grid view to
change between Film strip or Grid view.
3. Select a picture to show it in full on your screen.
4. Use now tu to step through the pictures collection.
5. Press the button to start a slideshow.
6. Click to zoom in or out.
7. You can call more functions like Rotate, Edit, Crop and Slideshow setup with .
5.4 Video player
Click the Video player icon in the launcher or on the Home screen, then press OK.
Choose a video and press OK to display the video.The Video player presents the video on your Micro
SD card or USB storage device including videos which have been downloaded from the web or
streamed from other locations.
5.5 Music library
Click on the Music icon in the launcher or on the Home screen. If you have copied music to your
Micro SD card or USB storage device and connected the Micro SD card or USB storage device to one
of the ports, it will search for music les and build a catalogue of your music, based on information
about each le that is stored in the le itself. Depending on the number of les it can take from a few
seconds to several minutes. When the catalogue is complete, the music library screen opens with
tabs so you can click to view your music library sorted by artists, albums, songs or playlists. Choose
the song you want to listen to and press OK.
5.6 File Manager
Click the File Manager icon in the launcher or on the Home screen, then press OK. In this menu you
can see folders and les on the external and internal memory. If you like you can Delete, Edit, Copy
les and Paste those to other folders. Also copy from external and internal memory or vice versa.
11

5.7 S link for streaming from other devices
Click on the S link icon in the launcher or on the Home screen. You will conveniently be able to
connect your mobile phone or tablet with your TV screen to watch pictures, videos and music from
these devices. You must also install apps from the Store on these devices to make it functioning.
5.8 The Store
Click on the Store icon in the launcher or on the Home screen. When you open the Store for the rst
time, please read and accept the terms of service to continue.
You need to create a Google Account or enter your existing account and password before you can
use the Store. This menu will guide you through the steps. Once ready you can start using the Store
market by following the steps below.
5.9 Applications
Note: STRONG cannot warrant and cannot be hold responsible of the (mal-)
function and working of third party apps. Some applications function only
well in devices with GPS.
5.9.1 Browse for applications
You can browse for apps by category and sort them in dierent ways.
1. Click a top-level category, such as Apps or Games. Click on a subcategory to view its list of apps.
2. Scroll to view subcategories and click on the one you want to explore. Click to view top paid,
top free or the most recent apps in this subcategory. Click on an app to open its details screen.
3. Click Top paid, Top free or Just in to sort the subcategory further.
5.9.2 Search for applications
1. Click the Search icon at the top right-hand side of the screen
2. Enter what you want to search for and click Search again. You can enter all or only a part of an
app’s name or description or the developer’s name which you want to search for. When you
nd an app you like, you can install it on your SD card or USB storage device.
3. Click on the Search result to open the details screen of that app.
The details screen describes the app and contains buttons for downloading it and performing other
tasks. You can also press and enter Setting.
5.9.3 Download and install an application
Find an app you want and open its details screen. In the details screen of the app, you can read more
about it including costs, rating and user comments and information about the developer. Click to
download and install the app. (If it is a paid app, the button is labelled with the price.) Wait until it is
installed and shows“open” to use this new app.
12

5.9.4 Create a Google WalletTM account
You can pay for the items you purchase from the Store with a Google WalletTM account. Set up a
Google WalletTM account the rst time you purchase an item from the Store or prior in a web browser.
In a web browser, go to https://wallet.google.com/ to establish a Google WalletTM account. Another
possibility is to set up a Google WalletTM account the rst time you use your Android IP Box to buy an
item from the Store when you are asked to enter your billing information.
Warning: When you have used Google WalletTM account once to purchase an app
from the Store, the Android IP Box remembers your password. For this
reason, you should secure your Android IP Box to prevent others from
using it without your permission.
5.9.5 Managing your downloads
After downloading and installation of an app, you can access the Store and enter the app name
again. Here you can rate it, view it in a list with your other downloaded apps and congure it
to update itself automatically and much more. Also you have the option to uninstall the app.
Alternatively you can select Settings, More Settings from the Home screen and click on Apps. In this
menu you can clear data, force stop or even uninstall the selected app.
Note: Be careful what you do in these menus as it can lead to deletion of settings,
app or users data.
5.9.6 View your downloaded applications
You can view a list of the apps that you have downloaded from the Store and use the list for a number
of purposes. On the Home screen, select the All App icon and press OK to see the installed apps.
5.10 Open all applications
Click on the All Apps icon in the launcher or on the home screen. This menu displays all your apps
short links on one or more screens. Press qonce and then use tu to see all apps. If you select one,
you can open it by pressing OK or press to manage apps or go directly to the Settings menu.
6.0 SETTING OF SYSTEM
Click on the Setting icon in the launcher or in the home screen. This menu allows you to set up all your
important settings such as Network, Bluetooth, Display, Sounds, Language and more.
6.1 Network
In this menu you can change or setup connection to the Internet by Wi-Fi or LAN (RJ45 cable). Enter
and store your passwords and/or gateway ports here.
13

6.2 Add accessory (Bluetooth)
This menu allows you to open the Bluetooth search detection ON or OFF, to setup new connections
to other Bluetooth devices.
If you like to make connection you need to open on both devices this function. With a conrmation
by numeric key you make a secured connection.
6.3 Display
Here you can set your Screen resolution, Screen position and Daydream.
6.3.1 Screen resolution
In this menu you can select your preferred HDMI output resolution which is supported by the
connected TV. The AUTO mode automatically selects the best output resolution of the combination
(so called 'handshake').
6.3.2 Screen position
Select Screen position if the size of the displayed screen is a bit too large or too small for the
connected screen.
6.3.3 Daydream
You can set your Daydream screen in None or Colours.
Choose the period of inactivity to start Daydream: (5, 10, 15, 30, 60 minutes, Never).
When to sleep: Screen turns OFF after this period of inactivity: (30minutes, 1, 3, 6, 12 hours, Never).
6.4 Sounds
In this menu you can setup the correct audio output setting if you like to use Dolby audio to connect
to a digital amplier.
System sounds: Select On to hear every time a click of remote buttons as conrmation. Select
O for no click sound.
Digital sounds: The selection HDMI sends Dolby audio. The selection PCM gives only Stereo
to all outputs.
6.5 Language
Select the OSD language which shall be used for the menus on screen.
6.6 Storage & Reset
This menu gives you an overview of your storage device.
You can also do a Factory data reset.
6.6.1 Storage
Here you get an overview from the used space on your storage device.
You can also clear your cached data for all apps in Cached data.
14

6.6.2 Factory data reset
Select this ONLY if you want to restore all settings back to factory default. All personal data will be
erased from the internal memory storage, including information about your Google WalletTM account,
other accounts, system and app settings and downloaded apps. When resetting the Android IP Box,
the system software updates you have downloaded and installed will not be deleted.
6.6.3 System Password
Default PIN code 1234.
6.6.4 System Password Change
To change the default password 1234 into a personal password:
Go to Settings -- Personal -- Security & Restrictions -- Change Password.
Here you have to enter the old PIN code and if accepted, you can enter the new PIN code.
You will be asked to enter the new PIN code again and the message Success will be shown.
6.7 Info (About)
Select this menu to see technical details of the IP Box as model name, software version, Wi-Fi MAC
address, Ethernet MAC address, IP address and serial number. You can also nd options to upgrade
the software.
6.7.1 Update
From time to time you can check if there is an improved software version available. This can be
checked and downloaded from our website www.strong.tv. Enter the type number into the service
support on our website. If there is an improved software version you can download the le and copy
it to the root of a USB device. Once ready insert the USB device to one of the free USB slots of the
Android IP Box. Select Local update and select the USB device and the upgrade le. Press OK and the
upgrade process will start.
Alternatively you can select Online update to upgrade the software directly from the server online.
This service is not available in all regions. Please, check information from your local dealer or visit our
website www.strong.tv for more information.
Note: Upgrades reset the Android IP Box back to the factory settings. Make
sure that you make a backup of the apps, or note the apps you have
downloaded before.
Warning: During the upgrade and ash process, do not switch o the main power!
Wait until the Android IP Box reboots and restarts automatically.
15

6.8 More Settings
In this menu you can set up, modify and change many settings of the Android part like you are used
to from your tablet or smartphone. All basic functions can be modied as Wi-Fi, Bluetooth, Ethernet,
Sounds, Display, Storage, Permissions and Managing installed apps.
6.9 HDMI CEC
CEC (Consumer Electronics Control) can be used for controlling your equipment with only 1 remote
control.
Set One key play to ON to use all connected CEC supported equipment that shall be switched ON
when SRT 2022 is switched ON by the remote control.*
Set One key power o to ON to use all connected CEC supported equipment that shall be switched
OFF when SRT 2022 is switched OFF by the remote control.*
* CEC supported equipment is NOT always compatible with each other.
7.0 TROUBLESHOOTING
There may be many reasons that aect the correct operation of your Android IP Box. If the IP Box does
not work as you expect, please follow the steps outlined below. If after performing these operations
the IP Box still does not work well, contact your dealer or service centre in your area or write an email
to our support via our website www.strong.tv.
If you experience problems, rst check whether it is caused by an application.Try to clear the data or
remove the app and check if this solves the problem. Please enter Settings – Apps -- (select the app) –
Clear data and then return to the menu and test if all works again.
If not successful you can reset the IP Box back to the factory settings and try to install it again. Refer to
chapter 6.6.2 of this user manual.
Warning:Do not open the IP Box cover. This action will damage the warranty seals
and warranty repairs will be denied.
Problem Possible reason Remedy
The remote control is not
working. The remote LED
is blinking 15 seconds after
pressing a button.
The battery is exhausted
The remote control is
incorrectly aimed. The USB
adapter of the remote control
has been removed.
Change the batteries
Aim the remote control at the IP
Box, or check that nothing blocks
the path to the IP Box front. Insert
the USB adapter belonging to the
remote control.
Some buttons of the remote
control are not working
The Air mouse function is
activated
Press to switch this function
OFF.
Cannot turn on the IP Box The power adapter is not
connected to the 230 V outlet
or 5 V plug into IP Box.
Check whether the power
connector is completely
plugged into the DC socket of
the IP Box.
16