Stryker 1588 Series User manual

11558888 AAIIMM VViiddeeoo CCaammeerraa
1588-010-000
1588-210-105
1588-610-122
1588-710-105
I of II
FR
DE
IT
PT
ES
NL
DA
EN FI
P29924F 2019/02

TTaabbllee ooff CCoonntteennttss
Warnings and Cautions........................................................................3
Cautions ...................................................................................3
Warnings: General........................................................................3
Warnings: ENV Mode ....................................................................4
Operating a Light Source ................................................................5
Product Description and Intended Use ...................................................... 6
Indications.................................................................................7
The Camera Console.....................................................................8
Front Panel...........................................................................8
Rear Panel ...........................................................................8
The Camera Head........................................................................9
The C-Mount Coupler ...................................................................10
Setup ...........................................................................................11
Setting Up the Console..................................................................11
Wiring Diagram ..........................................................................13
Setting Up the Camera Head...........................................................13
Setting Up the Coupler..................................................................14
Installing the Soaking Cap..............................................................15
Operation ......................................................................................17
Powering the Console On/Off ..........................................................17
Controlling Remote Video Accessories ...............................................17
Using the Camera Head Buttons.......................................................17
P (Picture) Button...................................................................18
W (White Balance) Button .........................................................18
Up and Down Buttons..............................................................19
Programming Camera Head Buttons..................................................20
Using the Touchscreen Interface ......................................................22
Home Screen .......................................................................22
Menu Screen........................................................................23
DRE Mode Screen .................................................................23
Using the Camera in ENV Mode .......................................................24
Performing the White Balance Test....................................................26
Advanced Features......................................................................26
Troubleshooting...............................................................................27
Reprocessing..................................................................................31
Cleaning the Console ...................................................................31
Cleaning, Disinfecting, and Sterilizing the Camera Head ...........................32
Warnings .................................................................................32
Cautions ..................................................................................32
Limitations on Reprocessing ...........................................................33
Materials and Equipment ...............................................................33
Instructions for Reprocessing ..........................................................35
Point of Use .........................................................................35
Containment and Transportation .................................................35
Cleaning.............................................................................35
High-Level Disinfection (Optional) ................................................37
Sterilization..........................................................................38
Maintenance...................................................................................40
Inspection.................................................................................40
Using Sterile Drapes ....................................................................40
Storage ...................................................................................40
Replacing the Fuses.....................................................................40
Periodic Maintenance Schedule .......................................................40
Expected Service Life ...................................................................41
Disposal...................................................................................41
Recycling Diagrams .....................................................................41
Console..............................................................................41
Camera Head.......................................................................42
P29924F 1 EN

Technical Specifications......................................................................43
Electromagnetic Compatibility..........................................................44
Symbol Definitions............................................................................51
EN 2 P29924F

WWaarrnniinnggss aanndd CCaauuttiioonnss
Please read this manual and follow its instructions carefully. The words warning, caution, and note
carry special meaning and should be carefully reviewed:
Warning Indicates risks to the safety of the patient or user. Failure to follow warnings
may result in injury to the patient or user.
Caution Indicates risks to the equipment. Failure to follow cautions may result in
product damage.
Note Clarifies the instructions or presents additional useful information.
An exclamation mark within a triangle is intended to alert the user to the
presence of important operating and maintenance instructions in the
manual.
A lightning bolt within a triangle is intended to warn of the presence of
hazardous voltage. Refer all service to authorized personnel.
CCaauuttiioonnss
To avoid potential damage to this device, please note the following cautions.
1. Carefully unpack this device and check if any damage occurred during shipment. If damage is
detected, refer to the standard warranty.
2. Never sterilize the camera console, because the delicate electronics cannot withstand this
procedure.
3. Ensure that the electrical installation of the relevant operating room complies with the NEC
and CEC guidelines.
4. Always treat the camera system with care. The camera system contains sensitive parts that
are precisely aligned and may suffer damage if dropped or mistreated.
5. Ensure that readjustments, modifications, and/or repairs are carried out by persons authorized
by Stryker Endoscopy.
WWaarrnniinnggss:: GGeenneerraall
To avoid potential serious injury to the user and the patient and/or damage to this device, please
note the following general warnings.
1. Must be a qualified physician to use this equipment.
2. Read this operating manual thoroughly, especially the warnings, and be familiar with its
contents before connecting and using this device.
3. Test this equipment prior to a surgical procedure. This unit was fully tested at the factory
before shipment.
P29924F 3 EN

4. The camera head surface may exceed 41 °C (106 °F) in operating conditions with high
ambient temperatures and it should be handled with caution.
5. The camera head and coupler are shipped non-sterile. You must sterilize these devices before
the first use and after each use. To prevent device damage and infection risk to the patient or
user, follow all cleaning and sterilization instructions in this manual.
6. Do not position the console so that it is difficult to disconnect the power cord from the supply
mains.
7. To avoid the risk of electric shock, this equipment must only be connected to a supply mains
with protective earth.
8. Multiple portable socket-outlets shall not be placed on the floor.
9. Never use the camera system in the presence of flammable or explosive gases.
10.Disconnect the console from the electrical outlet when inspecting fuses.
11.Do not remove covers on the console, as doing so may cause damage to electronics and/or
electric shock.
12.Do not disassemble any part of the camera head; doing so may break the seals, causing
leakage and/or electric shock.
13.Attempt no internal repairs or adjustments not specifically detailed in this operating manual.
WWaarrnniinnggss:: EENNVV MMooddee
WWAARRNNIINNGG -- IIMMPPOORRTTAANNTT SSAAFFEETTYY NNOOTTIICCEE -- LLAASSEERR RRAADDIIAATTIIOONN::
• Endoscopic Near-Infrared Visualization (ENV) mode controls a Class 1M laser emitted from
the L10 LED Light Source with AIM Technology (0220-220-300).
• Use of controls or performance of procedures other than those specified herein can result in
hazardous laser radiation exposure and can cause severe eye injury to the patient or user.
• To avoid exposure to laser radiation, follow all warnings and guidelines presented below and
throughout this user manual.
1. Before using ENV mode, read and be familiar with all instructions and warnings found in this
user manual and in user manual P27006 (English) or P27009 (multilingual) for the L10 LED
Light Source with AIM Technology.
2. Protect the 1588 AIM Video Camera against unqualified use.
3. Wear eye protection as appropriate. Refer to any applicable regional regulations or standards
for personal protective equipment.
4. Do not manipulate tissue while ENV mode is enabled. The camera is intended to visualize
tissue manipulation only while ENV mode is off.
5. When using ENV mode, do not view the light output with optical instruments (for example,
microscopes or magnifiers). Do not direct the light output in ENV mode into an area where
such instruments are likely to be used.
6. Do not enable ENV mode when the endoscope is outside of the patient’s body.
7. When ENV mode is enabled, never look into the following apertures or direct the light emitted
from the apertures toward another person:
• the light cable connection on the light source (if the cable is not attached)
• the end of the light cable (if the SafeLight adapter is attached)
EN 4 P29924F

• the endoscope tip
8. When ENV mode is enabled, never leave a SafeLight adapter attached to the light cable
without an endoscope attached. Laser radiation can continue to emit from the adapter.
9. Disconnect the light cable from the light source only when the light source is powered off or in
Standby mode.
OOppeerraattiinngg aa LLiigghhtt SSoouurrccee
Please note the following special warnings to avoid user or patient injury or product damage when
using a system with a light source.
WWAARRNNIINNGG -- IIMMPPOORRTTAANNTT SSAAFFEETTYY NNOOTTIICCEE -- HHIIGGHH TTEEMMPPEERRAATTUURREESS::
• When using a light source, fire and/or severe injury may result to the patient, user or inanimate
objects if the instructions in this manual are not followed.
• All light sources can generate significant amounts of heat (exceeding 41 °C/106 °F) at the
scope tip, the scope light post, the light cable tip, and/or near the light cable adapter. Higher
levels of brightness from the light source result in higher levels of heat. Always adjust the
brightness level of the camera and the monitor before adjusting the brightness level of the light
source. If the brightness level of the light source can be adjusted, set it to the minimum
brightness necessary to adequately illuminate the surgical site.
• In addition, adjust the internal shutter of the camera higher in order to run the light source at a
lower intensity. Avoid touching the scope tip or the light cable tip to the patient, and never
place them on top of the patient, as doing so may result in burns to the patient or user. In
addition, never place the scope tip, the scope light post, the light cable adapter, or the light
cable tip on the surgical drapes or other flammable material, as doing so may result in fire.
• Always place the light source in Standby mode before the scope is removed from the light
cable or the device is unattended. The scope tip, scope light post, light cable adapter, and light
cable tip will take several minutes to cool off after being placed in Standby mode, and
therefore may still result in fire or burns to the patient, user, or inanimate objects.
The warranty is void if any of the above warnings or cautions are disregarded.
P29924F 5 EN

PPrroodduucctt DDeessccrriippttiioonn aanndd IInntteennddeedd UUssee
The Stryker 1588 AIM (Advanced Imaging Modality) Video Camera with Infrared Compatibility (or
“1588 AIM Camera”) is an endoscopic camera system that is used to produce still and video
images in the surgical field during surgical endoscopic procedures. The system is sensitive in the
visible and infrared spectrum. The optical image is transferred from the surgical site to the camera
head by a variety of rigid and flexible scopes which are attached to the camera head. The system
consists of a camera control unit (CCU) and a camera head with an integral cable that connects to
the CCU.
A coupler is also available for attaching a scope to the camera head. The available models for
each part are listed below.
NNoottee -- For complete system requirements to use the camera’s Endoscopic Near-Infrared
Visualization (ENV) mode, see Stryker user manual P27006 (English) or P27009 (multilingual) for
the L10 LED Light Source with AIM Technology (0220-220-300).
CCoonnssoollee
1588-010-000 1588 AIM Camera Control Unit
CCaammeerraa HHeeaaddss
1588-210-105 1588 AIM Camera Head, C-Mount
1588-310-130 1588 Pendulum Camera Head with Integrated Coupler 1,2
1588-610-122 1588 AIM Camera Head with Integrated Coupler
1588-710-105 1588 AIM Inline Camera Head, C-Mount
CCoouupplleerr
1588-020-122 AIM Coupler, 18 mm, C-Mount 3
1Complete instructions are available in Stryker user manual P29925 (English) or P29926
(multilingual).
2Not compatible with ENV mode when the camera is used with the L10 LED Light Source with
AIM Technology.
3Complete instructions are available in Stryker user manual P30104.
The 1588 AIM console is also packaged with the following connection cables:
• Remote cables, 2.5 mm to 3.5 mm (Qty: 2)
• DVI-I cable (Qty: 1)
• Hospital-grade power cord (Qty: 1)
Contact your Stryker representative for availability of other cables that may be required for
alternate configurations.
EN 6 P29924F

IInnddiiccaattiioonnss
The Stryker 1588 AIM (Advanced Imaging Modality) Video Camera with Infrared Compatibility is
indicated for use in general laparoscopy, nasopharyngoscopy, ear endoscopy, sinuscopy, and
plastic surgery wherever a laparoscope/endoscope/arthroscope is indicated for use.
A few examples of the more common endoscopic surgeries are listed below.
• laparoscopic cholecystectomy
• laparoscopic hernia repair
• laparoscopic appendectomy
• laparoscopic pelvic lymph node dissection
• laparoscopically assisted hysterectomy
• laparoscopic and thorascopic anterior spinal fusion
• anterior cruciate ligament reconstruction
• knee arthroscopy
• shoulder arthroscopy
• small joint arthroscopy
• decompression fixation
• wedge resection
• lung biopsy
• pleural biopsy
• dorsal sympathectomy
• pleurodesis
• internal mammary artery dissection for coronary artery bypass
• coronary artery bypass grafting where endoscopic visualization is indicated
• examination of the evacuated cardiac chamber during performance of valve replacement
The users of the Stryker 1588 AIM Video Camera with Infrared Compatibility are general
surgeons, gynecologists, cardiac surgeons, thoracic surgeons, plastic surgeons, orthopedic
surgeons, ENT surgeons and urologists.
P29924F 7 EN

TThhee CCaammeerraa CCoonnssoollee
The camera console—or Camera Control Unit (CCU)—is the control center for the 1588 AIM
Camera, and it processes the video and photographic images produced during the surgical
procedure.
FFrroonntt PPaanneell
The console front panel features a touchscreen, where different menus can be accessed,
including the controls for adjusting the Light Level, Zoom Level, and White Balance, as well as
allowing the selection of Surgical Specialty settings that optimize camera performance for specific
surgical procedures. The touchscreen also allows activation of remote outputs, which are
commonly used with a Stryker digital capture console to record images and video.
See the Operation section for more detail on using the front panel.
321
11.. PPoowweerr SSwwiittcchh Powers the camera ON and OFF
22.. TToouucchhssccrreeeenn Allows navigation through different menus for
controlling the camera and adjusting the video
settings
33.. CCaammeerraa--CCoonnnneeccttoorr PPoorrtt Connects to the 1588 AIM Camera Head
RReeaarr PPaanneell
The console rear panel provides ports for connecting the 1588 AIM Camera to viewing and
recording equipment, such as video monitors and Stryker device control consoles.
9
10
87654321
EN 8 P29924F

11.. DDeevviiccee CCoonnttrrooll PPoorrtt Connects to a Stryker device control console (such as
the SDC3 or SIDNE®) to enable voice operation and/or
graphic tablet control
22.. RReemmoottee OOuutt 11 Connects to a video accessory remote input
33.. RReemmoottee OOuutt 22 Connects to a video accessory remote input
44.. SS--VViiddeeoo OOuutt Analog video output
55.. DDVVII OOuutt 11 Digital video output
66.. DDVVII OOuutt 22 Digital video output
77.. LLiigghhtt SSoouurrccee PPoorrtt Connects to Stryker light source
88.. AACC PPoowweerr IInnlleet Connects to AC mains with separable power cord
99.. FFuussee PPaanneell Contains two 1.6A 250V fuses (slow blow, high breaking
capacity 1500A, size 5 mm x 20 mm)
1100.. EEqquuiippootteennttiiaall
GGrroouunndd PPlluugg Connects to a potential equalization conductor. The resulting medical electrical system shall follow all
applicable IEC 60601-1 requirements.
TThhee CCaammeerraa HHeeaadd
The camera head connects to the camera console and produces video and photographic images,
which it relays to the camera console. Several controls are accessible through a button keypad
located on the top of the camera head (see the Operation section).
41 2 3
P29924F 9 EN

11.. SSooaakkiinngg CCaapp Protects the cable connector during cleaning,
disinfection, and sterilization
22.. CCaabbllee CCoonnnneeccttoorr Connects the camera head to the camera console
33.. CCaammeerraa CCaabbllee The camera cable length is 10 feet (3.05 m)
44.. CCaammeerraa HHeeaadd Produces photographic and video images, provides
camera controls, and connects with a focusing coupler.
TThhee CC--MMoouunntt CCoouupplleerr
The coupler threads onto the face of the camera head, enabling a scope to be attached to the
camera. It provides a focusing ring to adjust image sharpness.
It is recommended to use the camera with the AIM Coupler (1588-020-122). The AIM Coupler
enables use of ENV mode when the camera is connected to the L10 LED Light Source with AIM
Technology. Refer to Stryker user manual P30104 for complete AIM Coupler instructions.
1
23
4
11.. RReeaarr AAddaapptteerr Threads onto the camera head
22.. FFooccuussiinngg RRiinngg Adjusts the coupler focus
33.. EEnnddoobbooddyy CCllaammpp Secures the scope to the coupler
44.. SSccooppee EEnndd Receives the endoscope
EN 10 P29924F

SSeettuupp
Stryker Endoscopy considers instructional training, or inservice, an integral part of the 1588 AIM
Camera. Your local Stryker Endoscopy sales representative will perform at least one inservice at
your convenience to help set up your equipment and instruct you and your staff on its operation
and maintenance. To schedule an inservice, contact your local Stryker Endoscopy representative
after your equipment has arrived.
Setting up the 1588 AIM Camera involves three steps:
1. SSeettttiinngg uupp tthhee ccoonnssoollee
2. SSeettttiinngg uupp tthhee ccaammeerraa hheeaadd
3. SSeettttiinngg uupp tthhee ccoouupplleerr
WWAARRNNIINNGG --
• Always connect the console to an appropriate power source, using a hospital-grade power
cord. Loss of AC power will cause the camera to shut down and the surgical image to be lost.
• Only connect items to the 1588 AIM Camera that have been specified for use with the camera
system. Connecting incompatible equipment may cause unexpected results.
• When the camera system is used with other equipment, leakage currents may be additive.
Ensure that all systems are installed according to the requirements of IEC 60601-1.
• Equipment which employs RF communications may affect the normal function of the 1588 AIM
Camera. When choosing a location for the camera system, consult the Electromagnetic
Compatibility section to ensure proper function.
• Always set up the console in a location that allows adequate ventilation (airflow) to the
console. Insufficient ventilation may cause the console to overheat and shut down.
SSeettttiinngg UUpp tthhee CCoonnssoollee
Refer to the instructions below and the wiring diagram on the following page for a typical
1588 AIM Camera configuration.
1. Connect the console’s AC power to a hospital-grade outlet.
2. Connect one of the console’s DVI outputs to an available DVI input on a Stryker digital capture
console such as the SDC3 (0240–060–100).
• The 1588 AIM console can also be connected to additional SDC video inputs or directly to
one or more display monitors; the rear panel provides one analog and two digital-video
outputs:
OOuuttppuutt TTyyppee OOuuttppuutt CCaabbllee CCoonnnneeccttoorr
Analog S-VHS 1* S-VHS 4 pin Mini-Din
(push-only connectors)
Digital (standard) DVI-I1** and
DVI-I2** DVI 29 pin (push-only connectors, with two
tightening knobs)
P29924F 11 EN

* On some monitors, S-VHS inputs may be labeled Y/C.
** The DVI connectors can also output analog SXGA signals through a DVI-I to VGA adapter.
When using any device with unterminated analog video inputs, connect a cable from the VIDEO OUT of that device to the
VIDEO IN on the monitor.
3. Connect the DVI output from the Stryker digital capture console to the DVI input on the display
monitor. (The VisionPro 26" LED Display (0240-031-020) is shown as an example in the
following diagram.)
4. Using the provided remote cables, connect remote outputs 1 and 2 from the 1588 AIM console
to a Stryker digital capture console. (The remote inputs should be connected to the same
channel as the video input.)
• Devices connected to the remote outputs can be operated using the console touchscreen
or the P button on the camera head. See the Operation section for details.
• Once connected to the 1588 AIM Camera, the SDC3 can control ENV, Dynamic Range
Enhancement, and Strobe functions. The user can also customize button configurations
through the SDC3.
5. Connect a USB A-to-A cable from the Light Source output on the 1588 AIM console to the
CCU input on the L10 LED Light Source with AIM Technology (0220-220-300) or the Precision
LED Light Source (0220-220-000). It is recommended to use the USB cable (P30883)
provided with the Stryker light source, as use of third-party cables may prevent the devices
from properly communicating.
• To use ENV mode, the 1588 AIM Camera requires a connection to the L10 LED Light
Source with AIM Technology.
• The 1588 AIM Camera Head can be programmed to toggle Run/Standby controls on the
light source. Contact a Stryker representative for more information about enabling this
advanced feature.
EN 12 P29924F

WWiirriinngg DDiiaaggrraamm
SDC/SIDNE CCU
0240-060-100
1588-010-000
0220-220-300
0240-031-020
3
4
2
5
1
SSeettttiinngg UUpp tthhee CCaammeerraa HHeeaadd
WWAARRNNIINNGG -- Do not severely bend the camera cable or damage may result.
1. Unscrew the soaking cap from the cable connector on the camera head.
2. Align the arrow on the cable connector with the arrow above the camera-connector port on the
front console panel.
P29924F 13 EN

3. Push in the connector until it locks in place.
NNoottee -- To unplug the camera from the console, grasp the knobbed portion of the connector and
pull straight out.
SSeettttiinngg UUpp tthhee CCoouupplleerr
Steps 1–3 below provide instructions for connecting 1588 AIM Camera Heads to the AIM Coupler,
18 mm, C-Mount (1588-020-122). Refer to the bullets below for possible system variations:
• When using the 1588 AIM Camera Head with Integrated Coupler (1588-610-122), skip to step
2.
• When using the 1588 Pendulum Camera Head with Integrated Coupler (1588-310-130), see
Stryker user manual P29925 (English) or P29926 (multilingual).
• When using a direct-coupled C-Mount endoscope (a scope that requires no coupler), thread
the endoscope directly into the camera head until it forms a tight seal, and skip to step 3. (C-
Mount endoscopes are not compatible with camera heads that have an integrated coupler.)
WWAARRNNIINNGG --
• When attaching or removing the coupler, grip only the rear adapter, as twisting other parts of
the coupler with force may result in mechanical damage.
• Do not overtighten the coupler (or a direct-coupled C-mount scope), as this may damage the
front window of the camera.
1. Attach the coupler to the camera head.
• Gripping the rear adapter, screw the coupler clockwise onto the camera head until it forms
a tight seal (1588-210-105 and 1588-710-105 only).
EN 14 P29924F

NNoottee -- To remove the coupler, grip the rear adapter and unscrew the coupler
counterclockwise from the camera head.
2. Attach an endoscope to the coupler.
WWAARRNNIINNGG -- BBeeffoorree eeaacchh uussee,, cchheecckk tthhee oouutteerr ssuurrffaaccee ooff tthhee eennddoossccooppee ttoo eennssuurree tthheerree
aarree nnoo rroouugghh ssuurrffaacceess,, sshhaarrpp eeddggeess,, oorr pprroottrruussiioonnss..
NNoottee -- For a list of endoscopes that are compatible with ENV mode, see Stryker user manual
P27006 (English) or P27009 (multilingual) for the L10 LED Light Source with AIM Technology.
1
2
3
• Remove the coupler dust cap if it is present.
• Depress the endobody clamp
1
and insert a scope into the endobody
2
.
• Release the endobody clamp to secure the endoscope.
3. Attach a light cable from the light source to the light post on the endoscope
3
.
NNoottee -- A scope adapter may be required to connect the cable to the endoscope. See the light
cable user manual for more detail.
NNoottee -- Only the Stryker AIM SafeLight™ cable (0233-050-300) is compatible with ENV mode.
ENV mode will not function if other cables are used. Refer to the AIM SafeLight cable user
manual (P27701) for complete cable instructions.
WWAARRNNIINNGG -- WWhheenn ccoonnnneeccttiinngg aann AAIIMM SSaaffeeLLiigghhtt ccaabbllee ttoo tthhee eennddoossccooppee,, aallwwaayyss
ccoonnnneecctt tthhee ssccooppee aaddaapptteerr ttoo tthhee eennddoossccooppee bbeeffoorree ccoonnnneeccttiinngg tthhee aaddaapptteerr ttoo tthhee
ccaabbllee.. IIff EENNVV mmooddee iiss eennaabblleedd aanndd tthhee aaddaapptteerr iiss nnoott ccoonnnneecctteedd ttoo tthhee ssccooppee,, llaasseerr
rraaddiiaattiioonn wwiillll eemmiitt ffrroomm tthhee aaddaapptteerr tthhaatt ccaann ccaauussee sseevveerree eeyyee iinnjjuurryy ttoo tthhee ppaattiieenntt oorr
uusseerr..
IInnssttaalllliinngg tthhee SSooaakkiinngg CCaapp
Before reprocessing the camera head, the soaking cap must be installed to avoid damaging the
cable connector.
CCAAUUTTIIOONN --
Failure to properly tighten the soaking cap will corrode the connector pins and void the warranty.
• To install the soaking cap, screw the cap onto the threads of the cable connector until it forms
a tight seal.
• To remove the soaking cap, unscrew the cap and pull it away from the cable connector.
P29924F 15 EN

EN 16 P29924F

OOppeerraattiioonn
NNoottee -- Before operating the device, ensure all system components have been set up according to
the instructions in the Setup section.
PPoowweerriinngg tthhee CCoonnssoollee OOnn//OOffff
WWAARRNNIINNGG -- Before using the camera in a surgical procedure, test all system components to
ensure proper function. Ensure that a video image appears on all video monitors before beginning
any procedure.
1. Power on the monitor.
2. Press the power switch on the console to power the console on or off.
NNoottee -- A color bar pattern will appear on the monitor if the camera head is not connected to the
camera console. If the color bar appears, refer to the Setting Up the Camera Head section to
connect the camera head.
CCoonnttrroolllliinngg RReemmoottee VViiddeeoo AAcccceessssoorriieess
The camera can remotely control up to two functions of a video accessory, such as a Stryker
digital capture console. Commonly this enables the user to capture images or start and stop video
recording.
Remote video accessories can be controlled with the camera head’s P button or the console
touchscreen. See the following sections, Using the Camera Head Buttons and Using the
Touchscreen Interface.
NNoottee -- Controls for capturing photos or recording video require connecting a video accessory to
the console. See the Setup section for more detail.
UUssiinngg tthhee CCaammeerraa HHeeaadd BBuuttttoonnss
The camera head features a four-button keypad for controlling the device. The default button
functions are described below.
The camera head buttons can be customized differently for each surgical specialty. See the
Programming Camera Head Buttons section for more detail. The button configuration for the
P29924F 17 EN

selected surgical speciality will appear on the display monitor when the camera head is connected
to the console. The button configuration will disappear once the P button is pressed.
PP ((PPiiccttuurree)) BBuuttttoonn
The P button controls up to two functions of a remote video accessory. Commonly this enables
the user to capture images or start and stop video recording. (See the Controlling Remote Video
Accessories section for connection requirements.)
• Press the P button for less than two seconds to select Remote 1. One beep will sound. When
the camera is connected to a Stryker digital capture console, this will CCaappttuurree aa PPhhoottoo.
• Press the P button for more than two seconds to select Remote 2. Two beeps will sound.
When the camera is connected to a Stryker digital capture console, this will SSttaarrtt oorr SSttoopp
VViiddeeoo RReeccoorrddiinngg.
WW ((WWhhiittee BBaallaannccee)) BBuuttttoonn
The W button activates the White Balance function or the Zoom Cycle function.
• Press the W button for less than two seconds to activate the ZZoooomm CCyyccllee function. Each press
raises the Zoom Level in eight steps. When the Zoom Level reaches its maximum, pressing
the button again cycles the level back to the lowest setting.
• Press the W button for more than two seconds to activate the WWhhiittee BBaallaannccee function. White
Balancing will correct slight color differences that exist between different light sources or
endoscopes. See the Performing the White Balance Test section below.
EN 18 P29924F