Stryker S3 MEDSURG BED User manual

Medical
Stryker S3™ Quick Start Guide
Always refer to the product label and/or operations manual before using any Stryker product.

A
AD
E
F
G
H
I
Overview
Headboard
Patient Controls
Siderails
Nurse Control
Panel
Footboard
120V AC Outlet (optional)
Caster
Siderail Release
Handle
Brake Pedal
Siderail Controls
Steer Pedal
A
B
C
D
E
F
G
H
I
J
K
BC
J
K

Scales
Notes:

Nurse Controls: Bed Zero/Scale
(optional)
Zero the bed before patient admission. Before you help
the patient onto the bed, place all equipment, linens and
other items needed for the patient on the bed. Press and
hold Zero button and follow the instructions on the digital
display. All items located on the bed at the time the bed is
zeroed will not be added to the weight of the patient.
To take a weight, press and hold the Scale button.
1
21
2

Bed Exit
Notes:

Notes:

Chaperone®Bed Exit System (optional):
Arm/Disarm
The bed exit system is a three-zone center-of-gravity system
that tracks the position of the patient’s body weight and
sounds an alarm when 50 percent of the patient’s body weight
exits a zone.
To Arm
Before arming, make sure the bed has been properly
zeroed without the patient in the bed.
Push and release the Arm/Disarm key. The largest zone
(Zone 1) light will illuminate when armed. The system will
automatically select the largest zone as default.
To change the zone, push the Zone key
until the light indicating the desired zone comes on.
To Disarm
To deactivate Bed Exit, push and hold the Arm/Disarm key.
The selected zone light will turn off.
Note: If the bed was not zeroed at patient admission,
prior to arming, the Chaperone Bed Exit System will not
operate properly.
1
3
3
1
2
2

Zone 1 (default)
Allows the patient to move
freely on the bed, but alarms
when patient moves 50 per-
cent of body weight out of
the designated zone.
Zone 2
Allows limited movement.
Alarms when the patient
approaches the siderail or
foot end of the bed.
Zone 3
Allows very minimal move-
ment. Alarms when patient
moves out of the tightly
restricted zone.
Chaperone Bed Exit System: Zones

iBed™Awareness
Notes:

Nurse Controls: iBed™Awareness (optional)
The iBed Awareness is a bed monitoring system that allows you to monitor the brakes, siderail
position, bed exit, low bed height and 30 degree HOB.
To Arm
Set the desired bed configuration.
Push and release the iBED key (all three green lights on
the footboard will illuminate).
If one of the parameters is changed, an amber light on the
footboard will flash indicating the bed is no longer in the
prescribed position. The digital display and nurse dash-
board will indicate what has been altered.
To Disarm
To deactivate iBed Awareness, push and hold the iBED (1)
key. The footboard lights will turn off.
1
1
2
1
2
2

Controls
Notes:

Notes:

1
3
4 6 8
Nurse Controls: Bed Motion
Push to lower head end/raise foot end of bed.
(Trendelenburg position)
Push to lower foot end/raise head end of bed.
(Reverse Trendelenburg position)
Push to raise bed height.
Push to lower bed height.
Low Height will illuminate on the nurse dashboard
when the bed is at its lowest height.
Push to raise Fowler.
Push to lower Fowler.
Push to raise Knee Gatch.
Push to lower Knee Gatch.
1
3
4
5
6
7
8
2
2
57

Nurse Controls: Bed Motion Locks
Bed Motion Lock*
Locks all motion on bed, including siderail controls and
foot end controls. Button will illuminate when activated.
Fowler 30°+ Lock*
Raises the Fowler to 30° and locks out the Fowler control
at all locations. Fowler 30°+ on the nurse dashboard will
illuminate when activated.
Patient Fowler Lock*
Locks out Fowler control at all siderail locations. The
button will illuminate when activated.
Patient Gatch Lock*
Locks out Gatch control at all locations. The button
will illuminate when activated.
Patient Bed Up/Down Lock*
Locks out Bed Height control at all siderail locations. The
button will illuminate when activated.
* Press and hold the lock button to unlock.
1
3
Note: The Fowler will not go below
30° once the Fowler 30°+ lock is
activated.
4
5
1
3 54
2
2

Nurse Controls: Main Menu Features
Change Scale Units (lb or kg)
Press the Menu button.
Scroll down using the arrow keys to Scale Units and
press the ENTER button.
Select lbs or kg and press the ENTER button.
To Change Equipment
1. Select Change Equip. in the menu then press and hold
the ENTER button.
2. When the Add/Remove screen appears, add or remove
any equipment.
3. Press the ENTER button
4. Equipment Changed will be displayed when the system
completes the Change Equipment Adjustment. The status
screen will then display the weight of the patient only.
1
3
2
1 3
2

Emergency CPR
Button
A CPR button can be found on
the footboard control panel.
To Activate
Press and hold the CPR
button to get the bed to a
full flat position.
Cardiac Chair
Button
To Activate
Press and hold the
Cardiac Chair button to
put the bed into a cardiac
chair position. This button
is located on both head
end siderails and the nurse
controls.
1
1
2
2

Frame
Notes:

Emergency CPR
Release
The CPR release is located
under the sleep deck near the
top of the head end of the bed
on both sides.
To Activate
Squeeze one of the two
release handles, located
beneath the red CPR Release
labels, and the Fowler can be
quickly guided down to a flat
position.
For Your Safety
A CPR compression board
(optional) can be found on the
back of the headboard for
immediate use if a crash cart is
not available.

Integrated Pump
Holder
Located on the footboard and
used to hang additional
equipment to the bed such as
CPMs or SCD machines.
For Your Safety
A 120V AC outlet (optional) is
conveniently located under the
footboard to help prevent trip
hazards.

120V AC Outlet
(optional)
A 120V AC outlet is located
under the footboard at the foot
end of the bed. The 120V AC
outlet has its own power cord
located at the head end of the
bed and marked with a white
tag.
To Activate
Plug desired equipment into
120V AC outlet.
Plug in the power cord that
has a white tag (at the head
end of the bed).