Stuv 30-in Guide

Replacing refractors 1
Replacing of ashtray grate 2
Replacing of grate shaker 3
Replacing of drum bolt and bolt spring 3
Replacing of drum positioner 4
Rotation of drum 4
Replacing damper and regulator 5
Replacing of upper seal between body & drum 6
Replacing of lower seal between body & drum 8
Door locking 9
Replacing of panes 10
Replacing of anti-convection seals on solid door 11
Replacing of solid door pane 11
Replacing of door seals 12
Spare parts list 13
maintenance en 03-05
30-in
Maintenance

S30-in M. En
03-05
1
1
A
B
D
E
23
5 6
2 Tools needed:
- 1 flat screwdriver
- 1 Allen key n° 3 and 4
- 1 8mm open-end spanner
- 1 Adjustable locking wrench
- 1 socket-head screwdriver with
7mm and 8mm sockets
- 1 spatula
Replacing refractors
3 Open door using cold handgrip.
4 & 5 Remove steel rod supporting
horizontal vermiculite refractors.
It just needs pushing out of its
notches. Remove horizontal
vermiculite refractors (4C)
Then vertically remove smoke
deflector (4D &5).
Then remove horizontal refractors
from back of stove.
Smoke deflector must be removed at
least every other year to avoid soot
clogging flue pipe.
6 Re-assembly sequence:
- vertical refractors (4B)
- horizontal refractors at back of stove (4A)
- smoke deflector (5)
- horizontal vermiculite refractors (4C)
- steel rod
CC
4
1 General view of the Stûv 30-in
A Front panel
B Solid door
C Finishing frame
D Damper regulator
E Ashtray door
F Stove upper panel
F
A 5 parts
B 12 parts
C 2 parts
B
D
A
C
B

2S30-in M. En
03-05
2
2 Open a door.
Remove both front refractors.
4 & 5 Separate the grate in 3 parts. Position the lower grate in place.
Its 3 lugs should fit into half-moon recesses in bottom of stove.
Careful: A-shaped opening fits on the RH side.
1 Grate mechanism.
A Red knob of grate shaker
B Mobile upper grate
C Fixed lower grate
D Fork
3 Remove grate with its pin
6 Refit refractors. Using red knob of
grate shaker (pic. 1A & 6A) twist
fork (pic. 1D) full-lock (135° anti-
clockwise). Then position mobile
upper grate (pic. 1B) and make sure
its rod slides into fork (pic 1 D).
Replacing ashtray grate
1
A
B
C
D
4
A
5
3
1. Removal of grate
A6

2 Unscrew both grate shaker parts
holding red knob with RH and fork
with LH.
12
3
1 Open a door. Remove front refrac-
tors. Remove grate and grate
holder.
3 Unscrew red knob from rod to allow
both rod sections to be removed
from stove.
Replacing ashtray shaker
123
1 Open ashtray door with cold hand-
grip.
4
4 Unscrew red knob to remove spring.
2 Using 8mm key, undo two M5
screws.
3 Remove bolt from drum.
S30-in M. En
03-05
3
Replacing drum bolt & bolt spring

4S30-in M. En
03-05
1 2
2 Using 8mm key, undo 2 screws hold-
ing drum positioner.
To refit, insert positioner using
2 screws with fan-washers. Do not
tighten. Check that door lines up with
front panel and ashtray door before
tightening screws.
1 Open ashtray door with RH.
Replacing drum positioner
The positioner is the fixed female element in which the bolt inserts to immobilise the drum.
123
1 View of drum with :
- support bearings
- guide bearings
2 Rotate drum for easy access to bear-
ing (or to grip hook).
3 Insert a flat screwdriver between rail
and drum lower ring and raise drum
slightly. Using Allen key n°4 loosen
screw 2 or 3 turns and move grip
hook to the right then remove bear-
ing through hole.
Drum rotation
1. Replacing drum support bearing
grip hook
2’
2’

5S30-in M. En
03-05
4 5
4 Remove damper from inside and
regulator from outside stove.
1 2
2 Remove primary air deflector. 3 Using Allen key n°8 undo screw
holding damper regulator.
3
1 Remove both front refractors.
Replacing damper and regulator
2. Replacing drum guide bearing
12
2 Using Allen key n°4 undo bearing
axle pin. Don’t forget to refit washer
between bearing and drum lower
ring.
1 Rotate drum for easy access to bear-
ing

4 Remove front panel.
4
5 Undo 3 hexagonal headed screws to
release stainless-steel seal retainer.
5
6 Remove stainless-steel seal retainer.
6
6S30-in M. En
03-05
Carefully note seal position before removal.
1 2
2 Remove semi-circular panel. 3 Undo both side finishing frames.
3
1 Using Allen key n°3 unscrew semi-
circular panel on stove top.
Replacing upper seal between body & drum
789
7 Using an 8mm open-end spanner
and 8mm socket wrench, undo bolt
holding upper crosspiece.
8 Rotate drum 10cm to the right.
Remove upper crosspiece.
9 Remove both bottom front refrac-
tors from stove.

S30-in M. En
03-05
7
10
10 Remove stainless-steel primary air
deflector.
11
11 Remove 2 vertical protective sec-
tions by raising them through holes
provided for fixing the barbecue
grill.
12
12 Unscrew vertical seal retainer bolts
a few turns.
13 14
14 Fit new seal with flexible edge out-
wards and thin section against stove
face.
First refit the LH vertical seal retainer,
tightening only the bottom bolt, then
pull the seal upwards while tightening
the other 2 bolts. Proceed in the same
way for the RH side, then fit the rest of
the seal evenly along horizontal part.
Check seal tightness by rotating drum
several times.
13 Remove used seal.

Carefully note seal position before removal.
8S30-in M. En
03-05
5 6
5 Remove stainless-steel primary air
deflector.
6 Remove both vertical protective sec-
tions lifting them by holes provided to
fix barbecue grill.
23
3 Rotate drum 10cm to the right, then
remove upper crosspiece.
4 Remove both bottom front refrac-
tors from stove.
4
2 Using an 8mm open-end spanner
and 8mm socket, unscrew bolt hold-
ing upper crosspiece.
Replacing lower seal between body & drum
1
1 Open door slightly. Rotate drum
10cm to the right. Lift door out of
its hinges then push it to the left.
1
2

7 Undo Allen screw and M5 nut holding
lower crosspiece.
7
9S30-in M. En
03-05
8 9
9 Remove seal.
Refitting is in reverse sequence.
8 Position drum on solid door, remove
door by lifting it off its hinges.
Rotate drum to the left to bring the
15mm hole level with vertical body
seal. Hexagonal-head screw holding
lower horizontal seal retainer will
show through hole. Unscrew 2 or 3
turns, then perform same procedure
on RH side.
12
1 Using an 8mm socket undo
2 screws. Fit new striker plate.
2 Using socket spanner undo 2 screws
holding latch.
The door locks with 2 separate components :
A latch fixed to the drum and a striker plate fixed on the door.
Adjusting or replacing door locking mechanism

10 S30-in M. En
03-05
1
1
2
23
1 1. Slightly open door.
4 5 6
5 Replace pane.
2 Rotate drum 10cm to the right. Lift
door off its hinges, then push it to
the left. Rest it on a support to keep
it steady.
3 Remove door striker plate. Note its
position carefully !
8
8 Refit door.
6 Tighten pane clamps while pushing
pane down so as not to damage
pane edge. Barb-less edge should
face pane.
7
7 Refit door striker plate.
Replacing panes
4 Undo pane clamps.
Same procedure applies to glass door and/or “open fire” door.

11 S30-in M. En
03-05
123
1 Slightly open door.
4 5
5 Remove grey self-adhesive seal, fit
new pane with new self-adhesive
seal.
6
6 Insert screws for thermal shield.
2 Rotate drum 10cm to the right. Lift
door off its hinges, then push it to
the left.
3 Using an 87mm socket undo ther-
mal shield from solid door.
7
7 Insert upper seal between shield and
door. Using a spatula, slide lower
seal under lug, then insert rest of seal
along width of shield. Seals must fill
groove along its full length.
8 Refit thermal shield in place.
8
Replacing anti-convection seals and solid door pane
4 Remove thermal shield.
1
2

12 S30-in M. En
03-05
123
1 Slightly open door.
4
2 Rotate drum 10cm to the right. Lift
door off its hinges, then push it to
the left.
3 Remove door seal simply pulling it
out.
Replacing door seals
4 Using a spatula, replace seal starting
from bottom hinge side. For best
thermal performance, make sure
vertical sections are stretched and
spread remainder on horizontal sec-
tions.
1
2

13 S30-in M. En
03-05
Spare parts list for Stûv 30-in as of 02-05
Parts description Reference Part #
Primary air deflector page 14 pic. 5 A 30P1501NX
Thermal shield page 14 pic. 9 30P1502NX
Drum grip hook page 4 pic. 2 30P1505NX
RH facing page 14 pic. 1 A 30INMONTD
LH facing page 14 pic. 1 B 30INMONTG
Damper regulator page 14 pic. 6 30P201NX
Glass door page 10 pic. 1 30POV
Solid door page 14 pic. 1 C 30POP
“Open fire” door page 14 pic. 1 B 30POB
Front panel page 14 pic. 1 D 30FRON
Ashtray door page 14 pic. 1 E 30PORT
Ashtray page 14 pic. 8 A 30CEN
Upper protective crosspiece page 8 pic. 3 30PROTS
Lower protective crosspiece page 9 pic. 7 30PROTINF
RH vertical protective section page 8 pic. 6 30P312
LH vertical protective section page 8 pic. 6 30P313
Smoke deflector + lower smoke deflector page 1 pic. 5 30P314
Grate shaker page 14 pic. 10 30SGR
Drum positioner page 4 pic. 2’ 30P326
Mobile upper grate page 2 pic. 1 B 30P5003
Grate holder (fixed) page 2 pic. 1 C 30P5006
Complete damper assy page 14 pic. 6 30REG
Half-moon top panel page 14 pic. 1 F
Spray can Senotherm Stûv 930 page 14 pic. 3 A MA010
Handgrip (cold) page 14 pic. 3 B 20MAIN
Support bearing, kit, (3 bearings & 3 supports) page 14 pic. 4 A 30KRSUP
Guide bearing kit with washers & screws page 14 pic. 4 B 30KRGUI
Seal kit, between body & drum page 7 pic. 13 30KJCO
Lower seal kit, between body & drum page 9 photo 9 30KJCOINF
Seal kit, between body & solid door page 12 pic. 4 30KJPP
Seal kit, between glass door & drum page 12 pic. 4 30KJPV
Seal kit, between “open fire” door & drum page 12 pic. 4 30KJPB
Vertical refractor kit (12 pcs) page 14 pic. 2 B 30KREFRG
Horizontal refractor kit (5 pcs) page 14 pic. 2 A 30KREFRP
Horizontal vermiculite refractor kit (2 pcs) page 14 pic. 2 C 30DEVINF
Large curved glass pane 30 Neoceram VIT30
Small curved glass pane 30 Neoceram page 10 pic. 5 VIT301
Neoceram pane for solid door with 8mm self-adhesive sea page 14 pic. 1 F VIT302
Drum latch w/fixing screws page 9 pic. 1 & 2 30VERR
Lock for glass door & solid door SAV30VERROU
Lock for glass door & small door SAV30VERROU
Drum bolt page 14 pic. 7 30VERR
Adjustable leg MA0122

8
S30-in M. En
03-05
Warning !
Stûv stoves being constantly
improved, please give stove
serial number when ordering
spares to make sure the ade-
quate part is supplied.
A
45
6
3
A
A
A
B
14
1
D
C
E
B
A
F
9
7
10
B
2
B
D
A
C
B
F

Concept & Forme sa - rue Jules Borbouse 4 - 5170 Bois-de-Villers - Belgium
tel: [phone] - fax [phone]
[e-mail] - www.stuv.be