STW TC3G User manual

QUICK START GUIDE FOR STARTING UP
TC3G with machines.cloud

1 Check the scope of delivery
Connect the antennas to the SMA plugs.
2 Configuring the SIM card
1. Press the yellow button
beside the card tray
2. Remove the SIM card holder
(for micro SIM cards or smaller
cards a corresponding
adapter is required)
3. Place the SIM card into the tray
4. Slide in the fitted holder carefully
TC3Gi Breakout cables
Cable
harness
adapter Power supply
TC3Ge 2G/3G/4G Wi-Fi/Bluetooth GPS/GLONASS
Optional:

3 Starting up TC3G
1. Supply the TC3G with power:
a. Set the power supply to 12 V
b. Connect the TC3G to the breakout cables
c. Connect the breakout cables to
the cable harness adapter
d. Connect the power supply unit to
the cable harness adapter
e. ATTENTION: Select the correct power
supply output connectors
f. ATTENTION: Check the polarity of the power
supply output connectors
2. Switch on the cable harness adapter
3. Wait for the status LED of the TC3G
ATTENTION: For (optimal) GPS and GSM reception, the
TC3G must be positioned outside buildings

4 Status detection by LED light
Yellow Ready for use no Internet
access; GPS not active
or no GPS reception
The TC3G lights up yellow
after switching on
Blue No Internet access;
GPS active After booting the TC3G,
it may take a few minutes
for a GPS signal to be
received or for Internet
access to be established
Pink Internet access available;
GPS not active or no
GPS reception
Green Internet access
available; GPS active
Flashing Data traffic via CAN The flashing can occur
with all colors
Red
flashing
Error signal (see
operating instructions)
A restart of the TC3G
is recommended
5 Establish a connection with
machines.insight
1. Connect your smart phone, tablet or PC to the TC3G WiFi
network: Network name: TC3G-"serial number“
Password: see label on the TC3G
2. Open address
"192.168.201.1"
in your browser
3. Click on "Login" in the left menu bar
4. Login data: Username: admin
Passwort: admin
machines.insight

6 Configuring machines.insight
1. Select "System" in the left menu bar
2. Switch to Wi-Fi within
"Network Configuration“
3. Select the "Access Point"
window on the right
4. Change the password
for Wi-Fi access
5. Click on "Save"
6. Switch to "machines.cloud"
within the "Network
Configuration"
7. Switch the Activate
connector to "ON"
8. Click on "Save"
9. Switch to GSM within
"Network Configuration"
10. Does the SIM card
already have a PIN?
Set the PIN switch
in the GSM window to "Yes" and enter the PIN
11. Set GSM status to "ON"
12. Click on "Save" and restart the TC3G (switch
off/on the cable harness adapter)
ATTENTION: With M2M SIM cards further
configurations are necessary (Point 7 )

7 Configuring a M2M SIM card (only
necessary for M2M SIM cards)
1. Login as "admin" in machines.insight
2. Navigate to "System" "Network Configuration" "GSM"
3. Select the "Custom Configuration" field on the right
4. Enter M2M parameters (source: SIM card provider)
5. Click on “Save" and restart the TC3G (switch
off/on the cable harness adapter)

8 Registration in machines.cloud and
first steps
1. Open the e-mail from
no-[email protected]
with the link to the cloud
2. Click on the link and change your
password on the web page
3. Log in with the new access data
User name: tenantname_admin
4. Top right click on "<<"
5. In the area of “Help & Support” click on “T.O.N.I.”
(Toni the Guide) and then on “Show Tours”
6. The following tours are available:
a. Register Device
b. m.a Welcome Page
c. Create / Use VPN
d. Track Evaluation
e. Data Explorer

Sensor-Technik Wiedemann GmbH (STW)
Am Bärenwald 6
87600 Kaufbeuren
Telephone: [phone]
Telefax: [phone]
[email protected]
www.stw-mm.com
Further Information
Video Tutorials:
German: youtu.be/UTl4E_I39sE
English: youtu.be/dJcDs7t28yw
All Manuals and Tutorials here:
stw-digitalization.com
Password: connectivity
T.O.N.I. Tours:
Available in machines.cloud and machines.access
Top right click on „<<“
20190123–86876-EN–Irrtümer und Änderungen vorbehalten