Style selections 2165WWMV User manual

1
TENSION POLE
SHOWER CADDY
ITEM #1599749
MODEL #2165WWMV
Español p. 10
Serial Number Purchase Date
Questions, problems, missing parts? Before returning to your retailer, call our customer
service department at 1-877-888-8225, 8 a.m. - 8 p.m., EST, Monday - Sunday.
AR19036
IS2265
Style Selections is a trademark of LF,
LLC. All Rights Reserved.
ATTACH YOUR RECEIPT HERE
ADJUNTE SU RECIBO AQUÍ

2
TABLE OF CONTENTS
PART DESCRIPTION QUANTITY
A3/4 in. Tube 1
BStraight Tube 1
CLong Tapered Tube 1
DMedium Tapered Tube 1
EShort Tapered Tube 1
IS2265
Package Contents .......................................................................................................................... 2
Hardware Contents ........................................................................................................................ 3
Safety Information ........................................................................................................................... 3
Preparation ....................................................................................................................................... 3
Assembly or Installation Instructions ................................................................................................ 4
Care and Maintenance ..................................................................................................................... 9
Replacement Parts List .................................................................................................................... 9
PACKAGE CONTENTS
A
B
G
F
H
I
C
E
spring packed inside
D
PART DESCRIPTION QUANTITY
F Shelf 4
G Mirror 1
H Washcloth Bar 1
I Soap Dish 1
F
F

HARDWARE CONTENTS (shown actual size)
Spacer
Qty. 3
3
IS2265
PREPARATION
SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble, operate or install
the product.
• Before cutting, drilling or hammering into any wall surface, verify the location of electrical,
plumbing and gas lines. Cutting any of these may cause serious injury. If needed, contact
your electrician, plumber or service person.
Before beginning assembly of product, make sure all parts are present. Compare parts with package
contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble
the product.
Estimated Assembly Time: 25 minutes (with assistance of another person)
Tools Required for Assembly (not included): Tape Measure
AA
Small End Cap
Qty. 1
Large End Cap
Qty. 1
Wedge
Qty. 4
Transition Ring
Qty. 1
Spring Stopper
Qty. 2
Tape Strip
Qty. 1
BB CC DD
EE FF
GG

4
IS2265
1. Measure the distance between the tub ledge or
the shower stall oor to the ceiling to the nearest
half inch.
NOTE: See the below chart to determine what
tubes (C), (D) and (E) are needed.
NOTE: No matter the distance, tubes (A) and (B)
are ALWAYS used.
Please write down your measurements, tubes and
spacers needed below, you will need this later.
Opening Height:
Tubes Needed: A + B +
Number of Spacers (AA) Needed:
1
ASSEMBLY INSTRUCTIONS
tub ledge
(opening height)
shower stall oor
(opening height)
DISTANCE
TO CEILING
USE TUBES (C), (D), AND (E)
AS NEEDED
NUMBER OF
SPACERS (AA) USED
60 - 61.5 in. (D) 3
62 - 64 in. (C) 2
64.5 - 67 in. (C) 3
67.5 - 71 in. (C) and (E) 0
71.5 - 73 in. (C) and (E) 1
73.5 - 75 in. (C) and (D) 0
75.5 - 78 in. (C) and (D) 1
78.5 - 81 in. (C) and (D) 2
81.5 - 84.5 in. (C) and (D) 3
85 - 88.5 in. (C), (D) and (E) 0
89 - 91.5 in. (C), (D) and (E) 1
92 - 95 in. (C), (D) and (E) 2
95.5 - 97 in. (C), (D) and (E) 3

ASSEMBLY INSTRUCTIONS
Hardware Used
2. NOTE: THIS ASSEMBLY IS SHOWN FOR 97 IN.
OPENING HEIGHT. The following assembly
should be modied based on your opening height,
SEE CHART ON PAGE 4.
Place a wedge (DD) (tapered or rounded end up)
on a long-tapered tube (C) approximately half
way down and slide a shelf (F) down the tube
and t over the wedge (DD).
Place another wedge (DD) (tapered or rounded
end up) on a long-tapered tube (C) and slide
another shelf (F) down the tube and t over the
wedge (DD).
Repeat this step for the medium tapered
tube (D) and the other shelves (F). NOTE: Shelves
can be adjusted by moving the wedges (DD) up
or down.
Wedge x 4
DD
DD
5
3
3. Decide on which shelf (F) you would like to have the
washcloth bar (H) on.
Look under the shelf and slide the washcloth bar (H)
up into the groove of the left or right side of the
shelf (F) and push into place.
NOTE: The button on the back of the washcloth bar
MUST snap into the hole in the back of the shelf.
F
2
F
DD
H
hole
in shelf
C
IS2265

6
ASSEMBLY INSTRUCTIONS
4. Peel the paper backing off the double stick tape
on the mirror frame (G).
Slide the frame tab under the desired shelf (F)
and attach to the underside of the shelf front,
as shown.
IMPORTANT: Be sure of the mirror’s location,
once the mirror is in place, it is permanent.
5
5. Place the tapered end of the medium tube (D) into
the untapered end of the long tube (C), as shown.
4
F
tapered end
at the top
G
double
stick tape
D
C
tapered end
at the top
IS2265

ASSEMBLY INSTRUCTIONS
Hardware Used
6. Place the large end cap (CC) onto the short
tapered tube (E).
Place the tapered end of the short tapered tube (E)
into the untapered end of the bottom tube
assembly, as shown.
Large End Cap x 1
CC CC
7
7
Hardware Used
7. NOTE: ASSEMBLY SHOWN FOR 96 IN. OPENING
HEIGHT. The following assembly should be modied
based on your opening height, SEE CHART ON
PAGE 4.
Insert the spring stoppers (FF) into the ends of the
spring, as shown. NOTE: Spring is packed inside
straight tube (B).
Place straight tube (B) on top of the assembly and
insert three spacers (AA) into the straight tube (B),
as shown.
Spring Stopper x 2
FF
6
E
tapered end
at the top
bottom tube
assembly
Spacer x 3
AA
spring
B
tapered end
at the top
FF
FF
FF
AA
IS2265

8
8
Hardware Used
8. Place the small end cap (BB) onto the 3/4 in. tube (A).
Insert the transition ring (EE) into the straight tube (B).
Slide the 3/4 in. tube (A) through the transition
ring (EE) and into the straight tube (B), as shown.
Place the tape strips (GG) around the seams of
the tubes.
NOTE: After inserting the 3/4 in. tube (A) into
the straight tube (B) ensure that the transition
ring (EE) ts snuggly over the straight tube (B).
Transition Ring x 1
EE
Small End Cap x 1
BB B
BB
EE
GG Tape Strip x 1
A
B
A
B
C
GG
9. NOTE: Make sure you are installing in a clean,
dry and safe environment.
Compress the TOP of the unit against the ceiling in
the desired location, g 1.
Now, move the BOTTOM end into place so that the
unit is in a vertical position, g 2.
9g. 1
g. 2
ASSEMBLY INSTRUCTIONS
IS2265

ASSEMBLY INSTRUCTIONS
10. Install the soap dish (I) on any shelf (F). The tabs
on the bottom of soap dish (I) snap into place in
the holes in the shelves (F).
NOTE: The soap dish can be inserted in various
locations on each shelf according to your
preference. (Once installed, the soap dish
can be removed by rmly pressing in and up
on the tabs from under the shelf.)
GG
9
Printed in USA
10
F
I
CARE AND MAINTENANCE
Cleaning with a dry cloth may be sufcient, but for other stains or marks wipe gently with a damp cloth.
DO NOT use strong detergents or abrasive cleaners; they may damage the surface of the product.
PART DESCRIPTION PART #
AA Spacer
YP5346
BB Small End Cap
CC Large End Cap
DD Wedge
EE Transition Ring
FF Spring Stopper
REPLACEMENT PARTS LIST
For replacement parts, call our customer service department at 1-877-888-8225, 8 a.m. - 8 p.m., EST,
Monday - Sunday.
AA BB
CC DD EE FF GG
PART DESCRIPTION PART #
GG Tape Strip JWJF0222E
IS2265

10
POSTE ORGANIZADOR
PARA DUCHA
ARTÍCULO #1599749
MODELO #2165WWMV
IS2265
Style Selections es una marca de LF,
LLC. Todos los derechos reservados.
Número de serie Fecha de compra
¿Preguntas, problemas, piezas faltantes? Antes de volver a la tienda, llame a nuestro
Departamento de Servicio al Cliente al 1-877-888-8225, de lunes a domingo de 8 a.m. a 8 p.m.,
hora estándar del Este.