Sub-Zero UC-15I Guide

IN S TA L L AT I O N &OP E R AT I O N
UNDERCOUNTER IC E MA C H I N E

SUB ZERO®is a registered trademark of Sub Zero, Inc.
As you follow these instructions, you will
notice WARNING and CAUTION symbols.
This blocked information is important for the
safe and efficient installation of Sub-Zero
equipment. There are two types of potential
hazards that may occur during installation.
Another footnote we would like to identify is
IMPORTANT NOTE: This highlights informa-
tion that is especially relevant to a problem-
free installation.
signals a situation where minor injury or
product damage may occur if you do not
follow instructions.
states a hazard that may cause serious
injury or death if precautions are not
followed.
CONTENTS
Ice Machine Installation 4
Installation Checklist 16
Ice Machine Features 17
Ice Machine Operation 18
Ice Machine Care 23
Troubleshooting Guide 28
Service Information 30
Sub-Zero Warranty 31
Features and specifications indicated herein and
on the website are subject to change at any time
without notice. Check our website, subzero.com,
for the most up to date specifications.

3
T H A N K YO U
Congratulations on th purchas of your
Sub-Z ro ic machin . It produc s th sam
high quality cl ar ic that you would xp ct
from Sub-Z ro.
Th importanc of th installation of th ic
machin cannot b ov r mphasiz d. Installa-
tion should b don by a qualifi d install r.
B for you b gin th installation proc ss,
it is r comm nd d that you r ad th ntir
installation instructions. Th r ar k y d tails
that you should tak sp cial car to obs rv
during th installation. By r ading th s
instructions car fully, you will mak th
installation proc ss asi r, probl m-fr and,
most importantly, saf .
Any qu stions or probl ms about th
installation should b dir ct d to your
Sub-Z ro d al r or Sub-Z ro custom r s rvic
at 800-222-7820. You can also visit our w bsit
at subz ro.com.
Th Sub-Z ro ic machin is prot ct d by a
warranty that is on of th fin st in th
industry. Tak a mom nt to r ad th warranty
stat m nt on pag 31 and r f r to it should
s rvic b com n c ssary.
Th op ration information in this book will
answ r most of your qu stions about th
f atur s, op ration and maint nanc of your
ic machin . If you hav qu stions that ar not
addr ss d h r , call Sub-Z ro custom r
s rvic at 800-222-7820 or visit our w bsit
at subz ro.com.
S U B - Z E R O I C E M A C H I N E INSTALLATION AND OPERATION
IMPORTANT NOTE: Your Sub-Z ro ic
machin is d sign d and manufactur d with
th high st r gard for saf ty and p rform-
anc . It m ts or xc ds th standards of UL
and CUL. Sub-Z ro assum s no liability or
r sponsibility of any kind for products manu-
factur d by Sub-Z ro that hav b n alt r d
in any way, including th us of any parts
and/or oth r compon nts not sp cifically
approv d by Sub-Z ro. Sub-Z ro r s rv s th
right to mak d sign chang s and/or
improv m nts at any tim . Sp cifications and
d signs ar subj ct to chang without notic .
CO N TA C T
INFORMATION
Sub-Zero
customer service:
800-222-7820
Website:
subzero.com
Do not operate equipment that has been
misused, abused, neglected, damaged, or
altered/modified from that of original
manufactured specifications.
PRODUCT REGISTRATION C A R D
Th pack t containing this manual also
includ s warranty information. Warranty
cov rag b gins th day your n w ic machin
is install d.
IMPORTANT NOTE: Compl t and mail th
product r gistration card as soon as possibl
to validat th installation dat . If you do not
r turn your product r gistration card, Sub-Z ro
will us th dat of sal to th Sub-Z ro d al r
as th first day of warranty cov rag for your
n w ic machin .

IC E M A C H I N E REQUIREMENTS
Mod ls UC-15I and UC-15IO must hav
op n sit (gravity) drain availabl
(s pag 8).
A ground d, polariz d l ctrical pow r
supply on a s parat circuit s rvicing only
this applianc is r quir d. If GFCI (ground
fault circuit int rrupt r) is r quir d by your
local l ctrical cod or in an outdoor instal-
lation, it must b br ak r typ , not outl t
typ (s pag 7).
Must hav cold wat r supply lin availabl
at ic machin (s pag 8).
Cl aranc and air t mp ratur r quir m nts
must b m t (s pag 6).
If built into a cabin t, ic machin must b
r movabl for y arly cl aning proc dur
(s pag 23).
IMPORTANT NOTE: Failur to follow th s
installation guid lin s may aff ct warranty
cov rag .
Th mod l and s rial numb r ar list d on th
rating plat in th upp r l ft corn r of th ic
bin and on th back of th unit. R f r to th
illustration b low.
Dimensions in parentheses are in
millimeters unless otherwise specified.4
S U B - Z E R O I C E M A C H I N E I N S TA L L AT I O N
ACCESSORIES
Optional acces-
sories are available
through your
Sub-Zero dealer. To
obtain local dealer
information, visit
the Showroom
Locator section of
our website,
subzero.com.
M O D E L / S E R I A L N U M B E R L O C AT I O N
Models UC 15I, UC 15IP, UC 15IO & UC 15IPO
Proper installation requires connection to
the water supply, a drain and a dedicated
electrical circuit. These connections are
the responsibilities of the owner/operator.
Improper connections can result in
personal injury, substantial property
damage and erratic machine operation. If
you are unsure of your ability to safely
connect the ice machine, consult qualified
professionals or contact Sub-Zero.
Rating plat

5
S U B - Z E R O I C E M A C H I N E INSTALLATION
OVERALL DIMENSIONS
Models UC 15I, UC 15IP, UC 15IO & UC 15IPO
335/8"
(854) 335/8" (854)
143/4"
(375)
295/8"
(752)
4"(102)
215/16"
(541)
111/16"*(43)
215/16"
(541)
TOP VIEW
143/4"
(375)
115˚
DOOR SWING
SIDE VIEWFRONT VIEW
*Does not include door panel
61/2"
(165)
18"
(457)
A L L M O D E L S
Ov rall Width 143/4" (375)
Ov rall H ight (l v l rs in) 335/8"(854)
Ov rall D pth 23" (584)
Minimum Door Cl aranc 18" (457)
Rough Op ning Width 151/4" (387)
Rough Op ning H ight 341/2" (876)
Minimum H ight R quir d
(l v l rs in) 335/8" (854)
Rough Op ning D pth 24" (610)
Dimensions may vary ±1/8" (3).
24" (610)
ROUGH
OPENING
DEPTH
LOCATION OF
WATER LINE
8"
(203)
1/2"
(13)
TOP VIEW
341/2"(876)
ROUGH
OPENING
HEIGHT
335/8"(854)
MINIMUM
HEIGHT
REQUIRED
151/4"min (387)
ROUGH
OPENING WIDTH
POSITION OUTLET
WITH GROUNDING
PRONG ON RIGHT
FRONT VIEW
4" (102)
LOCATE
ELECTRICAL
WITHIN
SHADED AREA
INSTALLATION SPECIFICATIONS

6
S U B - Z E R O I C E M A C H I N E I N S TA L L AT I O N
LO C AT I O N O F I C E M A C H I N E
Th location s l ct d for th ic machin must
m t th following crit ria. If any of th s
crit ria ar not m t, s l ct anoth r location.
Th ic machin may b built into a
cabin t, how v r th location must allow
r moval of th ic machin for cl aning and
s rvicing. S rvic diagnostics ar
p rform d from th top of th ic machin .
Th location must b fr of airborn and
oth r contaminants.
Do not plac th unit within 18" (457) of a
trash compactor or trash/r cycling
contain r.
Th air t mp ratur must b at l ast 50°F
(10°C), but must not xc d 100°F (38°C) for
mod ls UC-15I and UC-15IP and 110°F
(43°C) for mod ls UC-15IO and UC-15IPO.
Th location must not b n ar h at-g n rat-
ing quipm nt.
Th location must not obstruct air flow
through th kickplat (airflow is in and out
th front of th ic machin ).
Th location must allow nough cl aranc
for wat r, drain and l ctrical conn ctions
at th r ar of th ic machin .
Mod ls UC-15IO and UC-15IPO may b
install d outsid .
AR E A REQUIREMENTS
Bfor moving th ic machin in plac , b
sur th finish d op ning dim nsions, l c-
trical and plumbing locations ar accurat .
Rf r to pag s 7–11.
B sur your plumb r, l ctrician and
cabin t install r hav this information b for
finishing work is compl t d.
Mod ls UC-15I and UC-15IO ar gravity drain
mod ls that r quir a drain tub that is
pitch d down from th outl t at th back of
th unit to th sanitary s w r conn ction.
Mod ls UC-15IP and UC-15IPO hav a built
in drain pump that will pump wat r up to a
drain point, such as a n arby sink. R f r to
sp cifications on pag s 8–9.
IMPORTANT NOTE: If th ic machin is
install d in a corn r, th door swing may b
limit d du to handl contact with th wall
or cabin t fac .
IMPORTANT NOTE: Th floor und r th
ic machin must b at th sam l v l as th
surrounding finish d floor.
IMPORTANT NOTE: Wh n you mov th
unit using a hand truck or dolly, position th
dolly on th sid of th unit and s cur th
door so it do s not op n whil transporting
th unit.
The ice machine must be protected if it
will be subjected to ambient tempera-
tures below 32°F (0°C). Component failure
caused by exposure to freezing tempera-
tures is not covered by the warranty. See
page 27.
Any finished flooring should be protected
with appropriate material to avoid any
damage from moving the unit.

7
Dimensions in parentheses are in
millimeters unless otherwise specified.
S U B - Z E R O I C E M A C H I N E INSTALLATION
IM P O RTA N T
N O T E
You must follow
all National
Electrical Code
regulations. In
addition, be aware
of local codes and
ordinances when
installing your
services.
IMPORTANT NOTE: Obs rv corr ct
polarity of incoming lin voltag .
Incorr ct polarity can l ad to rratic ic
machin op ration and a saf ty issu .
MINIMUM CIRCUIT REQUIREMENT
Th minimum circuit r quir m nt is us d to
h lp s l ct th wir siz of th l ctrical
supply. (Minimum circuit r quir m nt is not
th ic machin ’s running amp load.)
M A X I M U M B R E A K E R S I Z E A N D
M I N I M U M C I R C U I T A M P E R A G E
Voltag /Phas /Cycl 115/1/60
Maximum Fus /Circuit Br ak r 15
Minimum Circuit Amps 4.1
G F C I R E Q U I R E M E N T S
For Mod ls UC-15IO and UC-15IPO or if a
GFCI (ground fault circuit int rrupt r) is
r quir d by local l ctrical cod , it must b
br ak r typ .
ELECTRICAL REQUIREMENTS
Pr par l ctrical circuit b for installation of
your ic machin . Installation r quir s a
ground d (thr -prong), polariz d r c ptacl
with a s parat fus /circuit br ak r in an l c-
trical s rvic box.
V O L T A G E
All l ctrical work, including wir routing and
grounding, must conform to local, stat and
national l ctrical cod s. Th following pr cau-
tions must b obs rv d:
Th ic machin must b ground d.
A s parat fus /circuit br ak r must b
provid d for ach ic machin .
Th maximum allowabl voltag variation
is +/-10% of th rat d voltag at ic
machin start-up (wh n th l ctrical load
is high st).
Th minimum wir siz is #14 for l ss than
100 f t (30.5 m) or #12 for mor than 100
f t (30.5 m) to 200 f t (61 m) (solid
copp r conductor only). Th r comm nd d
br ak r is 15 amp. Local or stat l ctrical
cod , l ngth of run or mat rials us d, can
incr as th minimum wir gaug r quir d.
A qualifi d l ctrician must d t rmin th
prop r wir siz , although #14 is th
minimum siz allow d.
Do not use an extension cord or two-
prong adapter. Electrical ground is
required on this appliance. Do not remove
the power supply cord ground prong.

8
S U B - Z E R O I C E M A C H I N E I N S TA L L AT I O N
P L U M B I N G REQUIREMENTS
AT E R S U P P LY
Pr par wat r supply lin and drain b for
installation of your ic machin . Installation
r quir s a minimum 1/4" ID copp r cold wat r
lin and compr ssion fitting (not suppli d).
Mod ls UC-15I and UC-15IO ar suppli d with
a drain hos for gravity draining. Th optional
drain pump or pump mod ls UC-15IP and
UC-15IPO must b purchas d if a gravity drain
is not possibl . Both drain m thods r quir
routing to an op n sit drain. Do not conn ct
dir ctly to drain lin as bact ria from drain lin
may contaminat th ic machin .
Th includ d wat r filt r is d sign d to inhibit
scal formation, filt r s dim nt, and r mov
chlorin odor and tast . Th lif xp ctancy of
th wat r filt r is 6 months during normal
usag . Th ic machin control board will
monitor wat r usag and indicat wh n
r plac m nt is r quir d.
AT E R I N L E T L I N E S
Follow th s guid lin s to install wat r inl t
lin s:
Do not conn ct th ic machin to a hot
wat r supply. B sur all hot wat r r stric-
tors install d for oth r quipm nt ar
working. (Ch ck valv s on sink fauc ts,
dishwash rs, tc.)
If wat r pr ssur xc ds th maximum
r comm nd d pr ssur (80 psi–551.5 kPA),
obtain a wat r pr ssur r gulator from your
local plumbing contractor.
Install a wat r shut-off valv for th ic
making wat r lin s.
Insulat th wat r inl t lin to pr v nt
cond nsation.
D R A I N C O N N E C T I O N S
Follow th s guid lin s wh n installing drain
lin s to pr v nt drain wat r from flowing
back into th ic machin and storag bin:
Drain lin s must hav a 11/2" drop p r 5
ft of run (2.5 cm p r m t r), and must
not cr at traps.
Th floor drain must b larg nough to
accommodat drainag from all drains.
Drain pump discharg lin must t rmi-
nat at an op n sit drain.
Maximum ris – 12 f t (3.7 m)
Maximum run – 100 f t (30.5 m)
A P P R O X I M A T E H E I G H T O F
I C E M A C H I N E D R A I N
Standard installation 5" (127)
IM P O RTA N T
N O T E
Plumbing must
conform to state
and local codes.
Improper drainage can lead to water
flowing back into ice machine and poor
performance.

9
Dimensions in parentheses are in
millimeters unless otherwise specified.
S U B - Z E R O I C E M A C H I N E INSTALLATION
IM P O RTA N T
N O T E
Plumbing must
conform to state
and local codes.
PLUMBING REQUIREMENTS
ATER SUPPLY AND DRAIN LINE SIZING/CONNECTIONS
Water Water Ice Machine Tubing Size up to
Temperature Pressure Fitting Ice Machine Fitting
Ice Making
50°F (10°C) Min. 20 psi (137.9 kPA) Min. 1/4" (6.4) ID 1/4" (6.4) minimum
Water Inlet 80°F (27°C) Max. 80 psi (551.5 kPA) Max. Copp r Tubing insid diam t r
Water Outlet
3/4"(19) 3/4"(19) minimum
UC-15I and —— Hos Barb insid diam t r
UC-15IO
Water Outlet
3/8" (9.5) 3/8" (9.5)
UC-15IP and ——Hos ID minimum
UC-15IPO
NOTE: If air temperature is less than 60°F (16°C), water temperature must be equal to or greater than 50°F (10°C).
IMPORTANT NOTE: Although th ic
machin has b n d sign d to b s rvic d in
plac , in som cas s it may b n c ssary to
pull th unit out for s rvic . For that r ason
do not r strict acc ss to th unit at th front,
top and bottom.
If a floor is to b install d aft r th ic
machin , shims th thickn ss of th floor
should b install d und r th unit to k p th
ic machin l v l with th floor. Also, allow
1/8" (3) cl aranc on ach sid of th unit for
protruding scr w h ads.
Installations on a slab: Us a Mod l
UC-15IPO or UC-15IP, with built-in drain
pump and pump th wat r to th point of
drainag . Drain pump mod ls will pump
12 f t (3.7 m) high.
Installations over a crawl space or
basement:
If th r is not nough room
b hind th ic machin for a drain/wast
wat r r c ptacl , th drain will hav to b
b low th floor.

Dimensions in parentheses are in
millimeters unless otherwise specified.10
S U B - Z E R O I C E M A C H I N E I N S TA L L AT I O N
I N S TA L L AT I O N
INSTALLATION PROCEDURE
1) Pr par th sit by following th instruc-
tions und r El ctrical R quir m nts and
Plumbing R quir m nts on pag s 7–9.
2) R mov ic machin from carton.
3) Insp ct for damag .
4) R mov lit ratur /warranty pack t and
drain hos from insid th ic machin .
5) Adjust l g l v l rs. R f r to L v ling on
pag 12.
6) R v rs door if d sir d. S pag s 12–13.
7) Gravity drain model: Install drain hos to
drain on back of ic machin and rout to
op n sit drain. R f r to Plumbing R quir -
m nts on pag s 8–9.
Pump model: Rout drain tubing through
drain fitting on th back of th ic machin
and install drain hos on drain pump.
Rout oth r nd of drain tubing to drain
sit . R f r to Plumbing R quir m nts on
pag s 8–9.
8) Us compr ssion fitting to conn ct th
Wat r Inl t on back of ic machin to th
pr par d 1/4" ID cold wat r lin . R f r to
Plumbing R quir m nts on pag s 8–9.
9) Op n th shut-off valv on th wat r lin .
10) Ch ck all visibl conn ctions for wat r
l akag . Failur to do so could caus
flooding.
11) Conn ct l ctrical plug to ground d (thr -
prong), polariz d outl t. S El ctrical
R quir m nts on pag 7.
12) Plac ic machin back in position and
ch ck l v ling again. Mak any n c ssary
adjustm nts.
Connect to drain
The ice machine must be grounded in
accordance with national and local
electrical codes. Do not use an extension
cord or adapter.
Improper water supply and drain connec-
tions can result in personal injury and
substantial property damage. These
connections are the responsibility of the
owner/operator.
Drain
Fitting
Wat r
Inl t

11
S U B - Z E R O I C E M A C H I N E INSTALLATION
I N S TA L L AT I O N
13) Pr par sanitiz r solution and sanitiz
th ic machin according to In Plac
Cl aning/Sanitizing St ps 6 and 7 on
pag 25.
14) Put on gallon (4 L) of cold wat r into a
contain r that will asily pour und r th
lift d wat r shutt rs. R f r to pag 17 to
id ntify wat r shutt rs. Op n shutt rs
and add on gallon (4 L) of cold wat r.
Watch for prop r drainag .
15) Pr ss POWER button.
16) At initial start-up, ic machin will n d
approximat ly 30 minut s to fr z ic
and up to 5 minut s to harv st th ic .
Wait for first cycl of cub s to drop to
nsur prop r installation.
Th unit must b allow d to hav v ntilation
through th s fins. Th door pan l may hang
in front of th fins, but a d corativ kickplat
must not cov r th fins.
Th kickplat can b paint d anoth r color, if
you choos . Follow th s asy st ps:
Rough up surfac to b paint d with fin
grit sandpap r.
Wip with alcohol to nsur it is cl an
and dry.
Us an applianc or industrial grad , oil
bas , high gloss nam l paint.
Do not cover the kickplate area.
151/4"min
(387)
OPENING WIDTH
TOP VIEW
TOP VIEW
FRONT VIEW
1/8"(3)
DRAIN
TUBE
WATER
INLET TUBE SHUT-OFF
VALVE
DRAIN
TUBE
WATER
INLET
TUBE
SHUT-OFF
VALVE
DRAIN
INSTALLATION SPECIFICATIONS
Gravity drain model
151/4"min
(387)
OPENING WIDTH
TOP VIEW
TOP VIEW
FRONT VIEW
1/8"(3)
DRAIN TUBE
SHUT-OFF
VALVE
AIR GAP
DEVICE
DRAIN TUBE
AIR GAP
DEVICE
WATER
INLET TUBE
SHUT-OFF
VALVE
WATER
INLET TUBE
I N S TA L L AT I O N S P E C I F I C A T I O N S
Pump model

12
S U B - Z E R O I C E M A C H I N E I N S TA L L AT I O N
I N S TA L L AT I O N
L E V E L I N G
1) Adjust th l v l rs clos to d sir d h ight.
2) Mov th bin into its final position.
3) L v l th ic machin to assur that th bin
door clos s and s als prop rly. Us a l v l
on top of th bin. Turn th bas of ach foot
as n c ssary to l v l th bin. R f r to th
illustration b low.
S E C U R E T H E I C E M A C H I N E
To s cur th ic machin , install two
#8 x 1/2" flat h ad scr ws through ach hing .
R f r to th illustration b low.
S I D E P A N E L S
With th Sub-Z ro ic machin , you must
s cur ly fast n th sid pan ls to th adjac nt
cabin ts and floor.
Pan ls should b fast n d to th floor and walls
using ’L’ brack ts (hardwar not provid d). To
h lp you mov th unit into plac , rout out an
ar a in th floor so th ‘L’ brack t will sit flush
with th floor l v l. Brack ts and scr ws ar
provid d for mounting th unit to adjoining
cabin ts and sid pan ls.
R E V E R S E T H E D O O R S I N G
Th hing d sid of th door may b r v rs d
to th oth r sid if d sir d.
Th Sub-Z ro ic machin is shipp d with th
door hing d at th right. Th door and hing s
ar d sign d for placing th hing s on ith r
th right or th l ft sid of th unit. Moving th
hing s to th l ft in th pr -drill d hol s,
allows th door to pivot from th l ft sid .
R f r to th illustrations b low.
IMPORTANT NOTE: Th plastic molding
which cov rs th top ar a of th door,
packag d with th ic machin , is r quir d for
this proc dur .
1) To b gin, r mov th four scr ws that
s cur th door hing s to th ic machin .
R f r to th illustration b low.
NOTE: R mov th shim locat d b tw n
th cabin t and bottom hing , this shim
will transf r to th l ft sid bottom hing .
2) R mov th hing s from th door by
r moving th four scr ws (two ach hing )
that s cur th hing s to th door. R f r to
th illustration b low.
Leg leveler
Flat Head
Screws
Securing the ice machine Remove door Remove hinges and plastic
trim piece
St p 1 St p 2
St p 2
St p 3

13
S U B - Z E R O I C E M A C H I N E INSTALLATION
IN S TA L L AT I O N
3) Rmov th upp r plastic trim pi c (right
hand configur d) from th door by r moving
th two scr ws that s cur it to th door.
Th n r plac it with l ft hand trim pi c .
R f r to th illustration on pag 12.
4) Transf r th hing s to th l ft sid of th
door and r -attach. Th upp r hing will
n d to b com th low r hing and th
low r hing will now n d to b com th
upp r. R f r to th illustration b low.
5) R mov th top ic machin cov r by
r moving th two scr ws along th back of
th unit. R f r to th illustration b low.
6) Rmov four scr ws from th front top rail.
R f r to th illustration b low.
7) Pivot top rail nd for nd to xpos th two
l ft hand top hing scr w hol s and r install.
8) R mov 2 scr ws from bottom trim plat
and slid to cov r right hand hing
mounting scr w hol s and xpos l ft
hand hing mounting scr w hol s. R f r to
illustration b low.
9) Install th door using th l ft-hand door
mounting hol s. Install shim r mov d in
st p 1 b tw n th hing and cabin t.
10) Ch ck th op ration of th door by op ning.
Transfer hinges and reattach Remove top cover Remove front top rail Slide bottom trim plate
St p 4 St p 5
St p 6
St p 8

14
IN S TA L L AT I O N
DOOR PANEL INSTALLATION
You should b sur of th door pan l siz and
plac m nt b for proc ding with th installa-
tion. If you hav qu stions, contact your
Sub-Z ro d al r or cabin t suppli r. Instruc-
tions r garding sizing of th door pan l ar
provid d in th Sub-Z ro d sign guid .
For door handl hardwar , a D-styl pull
c nt r d on th dg opposit th door hing
sid is r comm nd d. Scr w h ads may hav
to b count rsunk to nsur that th hardwar
do s not int rf r with th pan l fitting flush
with th unit door.
Rmov th handl sid brack t attach d to
th front of th door and s t asid .
Plac th door pan l lying fac down on a
prot ct d surfac to nsur th front is not
scratch d or damag d.
Position th t mplat provid d flush with th
upp r dg of th door. B sur you ar
following th xact location for th RH or LH
door position. R f r to th illustration b low.
IMPORTANT NOTE: R m mb r you ar
vi wing th door pan l from th back sid in
th illustration. Th ov rall siz of th pan l
shown is th minimum siz n c ssary to cov r
th door of th unit. Th xact m asur m nts
of your door pan l may vary d p nding on th
particular installation you ar following.
Onc you hav locat d th prop r position for
th hardwar , mark th hol s, r mov
t mplat , and drill pilot hol s for mounting of
th hardwar . W r comm nd starting th first
f w hol s, positioning th hardwar , drilling
r maining pilot hol s, and s curing th
mounting brack ts with th #8 x 1/2" scr ws.
R f r to th illustrations b low.
Flush with Top and Side
of Panel
Template position
Right-hand door panel Left-hand door panel
PANEL
DESIGN
Additional panel
design information
can be found in
the Sub-Zero
design guide.
Check our website
at subzero.com.
DOOR PANEL DIMENSIONS
Door Pan l Width – 1/8" (3) r v al 15" (381)
Door Pan l H ight – 1/8" (3) r v al
4" (102) to spac 303/8" (772)
Door Pan l Thickn ss 5/8" (16) min
Door Pan l W ight 15 lbs (6.8 kg) max
Dimensions may vary +_ 1/8" (3).
S U B - Z E R O I C E M A C H I N E I N S TA L L AT I O N

15
Dimensions in parentheses are in
millimeters unless otherwise specified.
Install th door pan l by ngaging th tabb d
brack t to th door first and th n sliding th
hing sid hardwar ov r th positioning
scr ws. You will hav a 1/4" inch adjustm nt,
up and down, sid to sid , with this hardwar .
Onc you hav th door in plac , attach th
r maining #8 x 1/2" scr ws to th hing sid
mounting brack t and install d corativ caps.
90-DEGREE DOOR STOP
Th Sub-Z ro ic machin has a 90-d gr
door stop. Follow th s st ps for installation:
1) Op n th door approximat ly 80 d gr s.
2) Ins rt th stop pin into th bottom door
hing (pin nt rs from th top). Th pin
must b ins rt d until th h ad has mad
contact with th hing body. R f r to th
illustration b low.
3) Ins rt th stop pin into th top door hing
(pin nt rs from th bottom).
4) Ch ck for prop r op ration.
H I N G E C O V E R I N S T A L L A T I O N
IMPORTANT NOTE: Install th hing cov rs
aft r installation of th ic machin is
compl t . Th 90-d gr door stop must b
install d prior to installing th hing cov rs.
1) R mov th backing pap r of th adh siv
pads and bond to th hing .
2) Install c nt r cov rs (magn ts will s cur
th s cov rs). R f r to th illustration
b low.
IMPORTANT NOTE: Hing s must b fr of
dirt or gr as b for applying cov rs.
IMPORTANT NOTE: It will b n c ssary to
r mov th knock-out in th hing cov r wh n
th 90-d gr door stop is us d.
Door Stop Pin
Knock-Out
90-degree door stop Hinge cover installation
If the reveal on the hinge side of the door
panel is less than
1
/ 4 ", and the panel has
a square corner, severe finger pinching or
damage to the unit may occur.
Exercise caution when drilling holes for
mounting hardware. This is especially
critical with inset panels.
IN S TA L L AT I O N
S U B - Z E R O I C E M A C H I N E INSTALLATION

Has th ic machin b n install d wh r
th incoming wat r t mp ratur will r main
in th rang of 50–80°F (10–27°C)?
Is th ic machin drain lin rout d to an
op n sit drain for gravity drains and p r
instructions for pump units?
Has th own r/op rator b n instruct d
r garding maint nanc and th us of
cl an r and sanitiz r?
Has th ic machin and bin b n sani-
tiz d?
Hav th wat r and drain conn ctions b n
xamin d for l aks?
NOTE: If air t mp ratur is l ss than 60°F
(16°C), wat r t mp ratur must b qual to or
gr at r than 50°F (10°C).
16
If you are storing or disposing of your old
refrigerator, freezer or ice machine please
do it safely. Remove the doors or tightly
secure the doors closed. Child entrap-
ment accidents can be tragic.
CO N TA C T
INFORMATION
Sub-Zero
customer service:
800-222-7820
Website:
subzero.com
I N S TA L L AT I O N CHECKLIST
IMPORTANT NOTE: To nsur a saf and
prop r installation, th following ch cklist
should b compl t d by th install r to nsur
that no part of th installation has b n
ov rlook d.
Any qu stions or probl ms about th installa-
tion should b dir ct d to your Sub-Z ro
d al r or Sub-Z ro custom r s rvic at
800-222-7820. You can also visit our w bsit
at subz ro.com.
Ch ck to s if th unit is op rating b for
you install. If not, is th unit plugg d in? Is
th wat r turn d on?
If applicabl , is th door pan l install d
prop rly?
Hav any installation or s rvic probl ms
b n not d on th product r gistration
card? Instruct th own r to r gist r th
product.
Is th ic machin l v l?
Has all of th int rnal packing b n
r mov d?
Hav all of th l ctrical and wat r conn c-
tions b n mad ?
Has th supply voltag b n t st d and
v rifi d against th information on th
rating plat ?
Is th r prop r cl aranc in front of th
kickplat for air circulation?
Has th ic machin b n install d wh r
ambi nt t mp ratur s will r main in th
rang of 50–100°F (10–38°C) for mod ls
UC-15I and UC-15IP, and 50–110°F (10–43°C)
for mod ls UC-15IO and UC-15IPO?
S U B - Z E R O I C E M A C H I N E I N S TA L L AT I O N

17
Dimensions in parentheses are in
millimeters unless otherwise specified.
S U B - Z E R O I C E M A C H I N E FEATURES
A R R A N T Y
Sub-Zero products
are covered by a
two, five and
twelve year resi-
dential warranty
(exclusions apply).
See warranty
details at the end
of this guide.
Bin light
Wat r shutt rs
IC E M A C H I N E FEATURES
Und rcount r ic machin
Mod ls UC-15I and UC-15IO hav a gravity
drain, whil Mod ls UC-15IP and UC-15IPO
hav a built-in pump to allow gr at r instal-
lation fl xibility.
24" (610) d pth d sign for a compl t
int grat d look
Door acc pts custom pan ls
Automatic ic mak r provid s high-quality,
cl ar ic
Ic storag bin capacity of up to 25 lbs
(11 kg)
MODELS UC-15I, UC-15IP, UC-15IO & UC-15IPO
Ice Machine
Automatic d frost
R v rsibl door swing
Front v nting with r movabl kickplat
allows unit to b s rvic d from th front
Solid cor door with gask t and door clos r
UL approv d for US and Canada
Two, fiv and tw lv y ar r sid ntial
warranty – xclusions apply, s warranty
at th nd of this guid
Larg capacity
ic storag bin
Wat r r s rvoir
Control pan l
Ic scoop
R v rsibl door hing
Kickplat Rating plat
Wat r filt r
Gask t

18
BEFORE STARTING THE ICE MACHINE
S A N I T I Z E
It is important to cl an and sanitiz th ic
machin prior to us to nsur optimum ic
quality.
To nsur prop r op ration, follow th Op ra-
tional Ch cks on pag s 20–22. Starting th ic
machin and compl ting th Op rational
Ch cks ar th r sponsibiliti s of th
own r/op rator.
Adjustm nts and maint nanc proc dur s
outlin d in this manual ar not cov r d by th
warranty.
S U B - Z E R O I C E M A C H I N E OPERATION
Do not operate equipment that has been
misused, abused, neglected, damaged, or
altered/modified from that of original
manufactured specifications.
Do not store food or beverage in the ice
machine.

19
S U B - Z E R O I C E M A C H I N E OPERATION
CLEAN Button (Green)
Pr ssing th CLEAN button will initiat a cl an
cycl and d -activat th
ICE light. Th CLEAN
light will flash during th cl an cycl to
indicat th prop r tim to add ic machin
cl an r or sanitiz r.
Replace Filter (Red)
Wh n th ic machin compl t s 8000
fr z /harv st cycl s th light will illuminat to
indicat th filt r n ds r plac m nt. D pr ss-
ing th
CLEAN button for 6 s conds will r s t
th count r and light.
C O N T R O L P A N E L
FUNCTIONS
POWER Button (Green)
Pr ssing th POWER button onc will activat
th ic machin and gr n
POWER light.
Pr ssing th
POWER button a s cond tim will
d-activat th ic machin .
Automatic Ice Making Light (Blue)
Th ICE light is illuminat d wh n th ic
machin is in th ic making position. Th light
is off wh n th ic machin is in th cl an
cycl .
Delay Start
Pr ssing th DELAY button will initiat a d lay
cycl . Th ic machin will not run until th
d lay tim xpir s.
Pr ssing th button onc will illuminat th
2 hour light and initiat a two hour d lay
p riod.
Pr ssing th button a s cond tim will illu-
minat th 4 hour light and initiat a four
hour d lay p riod.
Pr ssing th button a third tim will illumi-
nat th
8 hour light and initiat an ight
hour d lay p riod.
Pr ssing th button a fourth tim will canc l
th d lay cycl .
I C E M A C H I N E C O N T R O L P A N E L

20
S E Q U E N C E O F OPERATION
D p nding on ambi nt conditions and cold
wat r supply t mp ratur , th ic making
proc ss will tak approximat ly 30 minut s.
1) Initial Start-Up or Start-Up After
Automatic Shut-Off Water Fill
B for th compr ssor starts, th wat r inl t
valv will purg old wat r from th syst m for
about 3 minut s.
2) Refrigeration System Start-Up
Th compr ssor starts aft r th Wat r Fill cycl
and r mains on throughout th Fr z and
Harv st cycl s. Th cond ns r fan motor starts
and runs throughout th Fr z cycl .
3) Freeze
Th wat r pump sprays wat r into th inv rt d
cups.
Th wat r fr z s lay r by lay r, until an ic
cub forms in ach cup. Th control syst m
will adjust th l ngth of th Fr z cycl to
conditions.
4) Harvest
Th wat r pump shuts off and th wat r inl t
valv starts up to assist harv st and r fill th
wat r sump.
Th vaporator is warm d, allowing th cub s
to r l as from th vaporator and drop into
th storag bin. Th control syst m will adjust
th l ngth of th Harv st cycl to conditions
and r gulat wh th r th cond ns r fan will
run.
At th nd of th Harv st cycl , th ic
machin will start anoth r Fr z cycl
(St p 3).
5) Automatic Shut-Off
Th l v l of ic in th storag bin controls th
ic machin shut-off. Wh n th bin is full, ic
will contact th bin th rmostat bulb hold r.
Th bin th rmostat bulb cools, which stops th
ic machin .
Th ic machin r mains off until ic no long r
contacts th bin th rmostat bulb hold r and
th th rmostat bulb warms up. Th incr as in
t mp ratur will r start th ic machin
(St p 1).
OPERATIONAL C H E C K S
Sub-Z ro ic machin s ar factory-op rat d
and adjust d b for shipm nt. Normally, n w
installations do not r quir any adjustm nt.
To nsur prop r op ration, always follow th
Op rational Ch cks:
wh n starting th ic machin for th first
tim
aft r a prolong d out of s rvic p riod
aft r cl aning and sanitizing
NOTE: Routin adjustm nts and maint nanc
proc dur s ar not cov r d by th warranty.
AT E R L E V E L
Th ic machin maintains th corr ct wat r
l v l. Th wat r l v l is not adjustabl .
B I N T H E R M O S TA T A D J U S T M E N T
Th bin th rmostat stops th ic machin
wh n th bin is full. Turn th th rmostat to th
l ft to d cr as th l v l of ic in bin or to th
right to incr as th l v l of ic in bin.
S U B - Z E R O I C E M A C H I N E OPERATION