Sub-Zero 427G User manual

INSTALLATION GUIDE
Wine Storage

Contents
Wine Storage ................................... 3
odels 424G and 424FSG Installation ............... 4
odels 427G and 427RG Installation ............... 16
odel WS-30 Installation ........................ 30
Installation Checklist ............................ 54
Service Information ............................. 55
Features and specifications are subject to change at any time
without notice. Visit subzero.com/specs for the most up-to-
date information.
I PORTANT NOTE: Throughout this guide, dimensions in
parentheses are millimeters unless otherwise specified.
Important Note
To ensure the safe and efficient installation of Sub-Zero
equipment, please take note of the following types of
highlighted information throughout this guide:
I PORTANT NOTE highlights information that is especially
relevant to a problem-free installation.
CAUTION signals a situation where minor injury or product
damage may occur if instructions are not followed.
WARNING states a hazard that may cause serious injury or
death if precautions are not followed.

Wine Storage 3
subzero.com
Sub-Zero Wine Storage
The importance of the installation of the Sub-Zero wine
storage unit cannot be overemphasized. Installation
should be done by a qualified installer.
Before you begin the installation process, it is recom-
mended that you read this entire installation guide. There
are key details that you should take special care to
observe during the installation. By reading these instruc-
tions carefully, you will make the installation process
easier, problem-free and, most importantly, safe.
Any questions or problems regarding the installation
should be directed to your authorized Sub-Zero dealer or
Sub-Zero customer care at 800-222-7820. You may also
check the contact & support sectionofour website,
subzero.com.
Important product information, including the model and
serial number of your unit are listed on the product rating
plate. For models 424G and 424FSG, the rating plate is
located on the underside of the top wall. For models
427G, 427RG and WS-30, it is attached to the underside
of the control panel. Refer to the illustrations.
odels 424G and 424FSG.
RATING PLATE
odels 427G, 427RG and
WS-30.
RATING PLATE

Models 424G and 424FSG Installation 4
Door swing clearances are based on stainless steel door
and handle dimensions.
237/8"(606) 24" (610)
34"
(864)
253/8"
(645)
4"(102)
23/8"(60)
ODEL 424G
Models 424G and 424FS
OVERALL DI ENSIONS
241/4"(616) 245/8"(625)
343/16"
(868)
4" (102)
253/8"
(645)
23/8"(60)
ODEL 424FSG

Models 424G and 424FSG Installation 5
subzero.com
Models 424G and 424FSG Installation
The model 424FSG wine storage unit is designed to be
attractive in a stand alone setting. Model 424G must be
built in. Refer to the previous page for overall dimensions
and door swing clearances for models 424G and 424FS.
Make sure that the finished rough opening where the
model 424G wine storage unit is to be installed is properly
prepared. Refer to the illustration. The floor under the unit
must be level with the surrounding finished floor.
I PORTANT NOTE: To operate properly, the door must
open a minimum of 90°. Use a minimum 3" (76) filler in
corner installations to assure a 90° door opening. Allow
enough clearance in front of the unit for full door swing.
TOOLS AND ATERIALS REQUIRED
•Appliance dolly able to support 130 lbs (59 kg) and
adequate manpower to handle the weight of the unit.
•Phillips and slotted screwdrivers.
•Allen, standard and crescent wrenches.
•Various sized pliers.
•5/16" hex bolt nut driver.
•Cordless drill and assorted drill bits.
•Level—2' (.6 m) and 4' (1.2 m) recommended.
•Masonite, plywood, pressed fiberboard, cardboard or
other suitable material to protect finished flooring.
•Appropriate materials to cover and protect the home
and furnishings during installation.
OPENING DI ENSIONS
24" (610)
OPENING WIDTH
24" (610)
OPENING
DEPTH
24" (610)
OPENING DEPTH
341/2"(876)
OPENING
HEIGHT
TOP VIEW
FRONT VIEWSIDE VIEW
ODEL 424G
Do not load wine into the wine storage unit until the
installation is complete.

Models 424G and 424FSG Installation 6
Electrical Requirements
For models 424G and 424FSG, the electrical supply
should be located within the shaded area shown in the
illustration. Follow the National Electrical Code and local
codes and ordinances when installing the receptacle. A
separate circuit, servicing only this appliance is required.
A ground fault circuit interrupter (GFCI) is not recom-
mended and may cause interruption of operation.
I PORTANT NOTE: For model 424G, the electrical outlet
must be placed so the grounding prong is to the right of
the thinner blades. The outlet must be flush with the back
wall.
Do not use an extension cord or two-prong adapter.
Electrical ground is required on this appliance. Do not
remove the power cord ground prong.
Electrical Requirements
Power Supply 115 V AC, 60 z
Circuit Breaker 15 amp
Receptacle 3-prong grounding-type
FRONT VIEW
151/2"
(394)
3" (76)
2" (51)
LEFT SIDE
OF OPENING
Location of electrical supply.
The outlet must be checked by a qualified electrician to
be sure that it is wired with the correct polarity and is
properly grounded.

Models 424G and 424FSG Installation 7
subzero.com
Electrical Requirements
HO E ALAR SYSTE
If a home alarm system is to be used, refer to home alarm
connections on page 11. In addition to operating power,
the installer may also be required to supply a home
automation system lead to the unit. This is for a low-
voltage, low-current signal similar to door and window
sensor signals. Common, normally open and normally
closed contact configurations are provided.
Three 1/4" female spade connectors are located in the
compressor compartment and are accessible behind the
kickplate on models 424G and 424FS. A minimum of 36"
(914) of lead wire should be provided for each contact,
exiting the back wall near the electrical outlet.
Before moving the wine storage unit in to position,
protect any finished flooring with appropriate materials
and secure the door closed.
Moving the Unit
Before moving the wine storage unit into position, make
sure all opening dimensions and electrical requirements
are complete and accurate.
I PORTANT NOTE: The floor under the undercounter unit
must be at the same level as the surrounding finished floor
to allow for removal of the unit for servicing.
Use an appliance dolly to move the wine storage unit near
the installation opening. Position the dolly at the side of
the unit to prevent damage to finished surfaces. Remove
and discard all packing materials and tape.
I PORTANT NOTE: Do not discard the kickplate, anti-tip
bracket and hardware. These items will be needed for the
installation.
All roller-assembly wine shelves should be removed to
reduce weight and prevent them from rolling. To remove,
pull the shelf out to its full extension, gently and evenly lift
up on both sides of the front of the shelf and remove.
Reverse the procedure to reinstall the shelf.

Anti-Tip Bracket Installation
ODEL 424FSG
If you are installing the model 424FSG in a space deeper
than 245/8"(625), the anti-tip bracket must be installed no
more than 245/8"(625) deep, so it engages the unit
properly. It is important that this measurement be made
from the front surface of the door, to the back of the anti-
tip bracket. Refer to the illustration below.
An anti-tip bracket and hardware is provided with the wine
storage unit. The anti-tip bracket must be installed on a
solid base to prevent tipover in case several loaded wine
shelves are extended at the same time.
ODEL 424G
The anti-tip bracket should be attached to the wall behind
the unit with the bracket flange located immediately above
the top of the unit. Refer to the illustration below.
For installations that cannot accommodate the anti-tip
bracket, the optional countertop bracket (provided) can be
used to secure the model 424G. This bracket will secure
the front of the unit to the underside of the countertop,
above the unit. Refer to the illustration below. If it is not
possible to use the countertop bracket, wedge shims
along the sides and top of the unit to secure.
Models 424G and 424FSG Installation 8
1/4"(6)
ANTI-TIP
BRACKET
Anti-tip bracket (424G). Countertop bracket
COUNTERTOP
BRACKET
To prevent the unit from tipping forward and provide a
stable installation, the unit must be secured in place
with the anti-tip bracket.
ANTI-TIP BRACKET
Anti-tip bracket (424FSG).

Anti-Tip Bracket Installation
ODEL 424FSG—WOOD FLOORS
Use the four #12 x 21/2" wood screws and the four 1/4"
flat washers provided. Drill pilot holes 3/16"(5) diameter
maximum, and be sure that the screws penetrate through
the flooring material and into the wall plate a minimum of
3/4"(19). Be sure that the screws hold tight. Refer to the
illustration below.
ODEL 424FSG—CONCRETE FLOORS
Use the two 3/8" x 33/4" concrete wedge anchors, two
#12 x 21/2" wood screws and two 1/4" flat washers
provided. Be sure that the anchors and screws hold tight.
Refer to the illustration below.
I PORTANT NOTE: In some installations the subflooring
or finished floor may require angling the wood screws
used to fasten the anti-tip bracket to the back wall.
Models 424G and 424FSG Installation 9
subzero.com
ake sure that there are no electrical wires in the area
which the screws could penetrate.
12 3/16"
(310)
12 3/16"
(310)
24"
(610)
C
L
FINISHED FLOORING
UNDERLAYMENT
WALL PLATE
SUBFLOORING
WOOD FLOOR
Wood floors. Concrete floors.
24"
(610)
C
L
11/2"
min
(38)
12 3/16"
(310)
12 3/16"
(310)
FINISHED FLOORING
UNDERLAYMENT
WALL PLATE
SUBFLOORING
CONCRETE
FLOOR
INSTALL CONCRETE WEDGE ANCHORS:
1) Drill a 3/8"(10) diameter hole any depth exceeding the
minimum embedment. Clean the hole or continue
drilling additional depth to accommodate drill fines.
Use a carbide drill bit manufactured within ANSI
B94.12-77.
2) Assemble the washer and nut flush with the end of
anchor to protect threads. Drive the anchor through the
material to be fastened until the washer is flush with
the surface material.
3) Expand the anchor by tightening the nut 3–5 turns past
hand-tight position or to 25 foot-pounds of torque.
Always wear safety glasses and use other necessary
protective devices or apparel when installing or
working with anchors.
Anchors are not recommended for use in lightweight
masonry material such as block or brick, or for use in
new concrete which has not had sufficient time to cure.
The use of core drills is not recommended to drill holes
for the anchors.

Models 424G and 424FSG Installation 10
Position the Unit
If you are adding an accessory lock kit to your wine
storage unit, it should be installed before you position the
unit. The accessory lock kit and additional instructions are
available through your authorized Sub-Zero dealer, or call
Sub-Zero at 800-222-7820. You can also visit our website
at subzero.com.
I PORTANT NOTE: If for any reason the wine storage unit
has been laid on its back or side, you must allow the unit
to stand upright for a minimum of 24 hours before con-
necting power.
Plug the power cord into the grounded electrical outlet.
With power applied to the appliance, check for lighting
and cooling before going any further. Once you are satis-
fied that the unit is operating properly, shut off power to
the electrical outlet at the circuit breaker and proceed.
Pre-level the wine storage unit before sliding it into
position. Leveling cannot be completed with the unit
pushed back in the installation opening.
If a home alarm system is to be used with the wine
storage unit, the lead wires should be threaded into the
compressor compartment before you position the unit.
Refer to home alarm connections on the following page,
for the location of these lead wires. After the unit is in
position, the alarm wiring can be completed from the front.
For model 424FSG, adust the leveling legs so the top of
the unit is no more than 345/8"(879) above the floor. This is
to allow the unit to engage the anti-tip bracket properly.
Center the model 424FSG in front of the anti-tip bracket.
Slide the unit into position, making sure the anti-tip
bracket is engaged properly.
When the wine storage unit is installed, the anti-tip
bracket will be positioned just below the engaging bracket
on the unit. It is not necessary to raise the unit up so that
it locks into the anti-tip bracket, but the unit must be in
alignment with the anti-tip bracket.
The wine storage unit provides the best access to its
contents when the front surface of the door panel extends
out from surrounding cabinets approximately 1/4"(6). For
model 424FSG, if there are no surrounding cabinet
surfaces to gauge depth, slide the unit back until it
engages the anti-tip bracket.
I PORTANT NOTE: The floor under the wine storage unit
must be at the same level as the surrounding finished floor
to allow for removal of the unit for servicing.

Level the Unit
Using an adjustable wrench or pliers, turn each of the four
leveling legs clockwise to raise the unit and counterclock-
wise to lower the unit. Refer to the illustration below for
location of the leveling legs.
For model 424G, the countertop bracket should be used
to make a solid installation. Refer to the illustration on
page 8. If this is not possible, wedge shims along the
sides and top.
ome Alarm Connections
Before the kickplate is installed, all necessary wiring
connections in the compressor compartment should be
completed.
If a home alarm system is to be installed on the wine
storage unit, the connections should be made using the
logic supplied with the alarm specifications. Refer to the
illustration for the appliance lead locations, and refer to
the following for color codes:
•Normally open contacts – white with red stripe wire
•Normally closed contacts – white with blue stripe wire
•Common – gray with white stripe wire
Use the 1/4" spade terminals or wire nuts provided to
make the proper wiring connections.
I PORTANT NOTE: If you are not responsible for alarm
system connection, this information should be supplied to
the home security system contractor.
Models 424G and 424FSG Installation 11
subzero.com
The alarm circuit in the unit is intended as a low-
voltage, low-current device only. It should not be used
to switch line power.
Any unused terminals should be completely insulated
and all wires should be secured away from conductive
or moving components.
To reduce the possibility of the unit tipping forward, the
front leveling legs must be in contact with the floor.
LEVELING LEGS
Leveling legs. Home alarm connections.
HOME ALARM
CONNECTIONS

Kickplate Installation
Once the unit is leveled and wiring connections made,
the kickplate can be installed. Use the two #10 x 1/2"
stainless steel screws that are provided with the kickplate.
Refer to the illustration below.
I PORTANT NOTE: The kickplate must be removed for
servicing. The floor cannot interfere with removal. The
louvered section of the kickplate must not be covered so
as to prevent air circulation.
Turn power back on to the electrical outlet.
Door Panel
ODEL 424G
Model 424G is offered in two design applications; stain-
less steel (/S) and overlay (/O). Each of these designs have
a full-view glass door.
The stainless steel model 424G/S is shipped from the
factory with the decorative stainless steel door panel and
matching handle in place.
The overlay model 424G/O is designed to accept a deco-
rative door panel to match surrounding cabinetry. The
door panel and the handle will be provided by the
customer.
Before beginning installation, check for the correct com-
ponents for the fit and finish desired. All overlay doors
require a decorative panel 233/4"(603) x 301/16"(764), a
minimum 5/8"(16) thick.
I PORTANT NOTE: For installations at or above 5,000'
(1524 m) in altitude, a special high altitude glass door unit
( AG) must be ordered.
If you have questions, contact your authorized Sub-Zero
dealer or cabinet supplier. Additional panel information
can be found in the Sub-Zero design guide.
Models 424G and 424FSG Installation 12
KICKPLATE
Kickplate installation.
A solid panel cannot be installed over the glass door,
as this may cause moisture to form behind the panel.

Overlay Door Panel
ODEL 424G
Inspect the door panel for the minimum 5/8"(16) thickness,
the finished inside edge. The glass door has a 10 lbs (5 kg)
weight limit. Refer to the wine storage section of the
Sub-Zero design guide for additional panel information.
Decide if the handle will be attached through the glass
door frame or just through the decorative door panel. If it
is just through the door panel, the handle must be
attached first.
Decorative panels are attached to the model 424G door
using #8 x 5/8" square drive screws passing through the
door frame from the rear, behind the gasket into the panel.
The door panel is marked for screw locations by the use of
tenon centers, which are temporarily inserted into the
1/4"(6) diameter holes in the front of the glass door frame.
Refer to the illustration below.
With the wine storage unit secured in position and the
door closed, the panel is held in the desired position on
the door and rapped by hand from the front, putting center
marks on the rear surface of the panel. If the door panel is
made of such a material that pre-drilling is needed, all of
the mounting holes should be marked. If not, only enough
holes to hold the panel in place temporarily, are necessary.
The door panel is then lowered from the door frame, tenon
centers removed, the door opened and the screws driven
into the panel through the black tape on the door frame,
using the center marks to locate the screws.
The screw holes inside the door are hidden under a cover
flap on the door gasket. It is necessary to lift the flap to
insert the screws. Use as many screws as necessary to
hold the door panel in place properly.
I PORTANT NOTE: After the first three or four mounting
screws are in place, but not completely tightened, close
the door and check your panel fit. This is the time to make
small adjustments. Once you are satisfied with the appear-
ance, open the door and apply the remainder of the
screws. Check all screws for tightness.
The metal frame on the glass door has numerous
mounting holes on each side of the door. This is to
accommodate the Sub-Zero accessory handles and
provide for easy attachment of the handle through the
door frame.
If you choose not to use the pre-drilled handle mounting
holes, it will be necessary to fasten the handle from the
rear of the door panel only, or drill one or more additional
holes through the metal frame of the glass door.
The cross section illustration shows how this hole passes
through the door frame. The hole center is on the small
locator groove in the front of the frame. A 1/4"(6) diameter
hole is made in the front wall of the extrusion and a 13/32"
(11) diameter hole through the rest of the frame.
Models 424G and 424FSG Installation 13
subzero.com
Overlay panel. Door frame cross section.
GASKET
GLASS
13/32"(11)
DIAMETER
1/4"(6)
DIAMETER
OVERLAY
PANEL
DOOR
FRAME
TENON CENTER

Models 424G and 424FSG Installation 14
Overlay Door Panel
I PORTANT NOTE: Install screws in all the mounting
holes in the door frame. The nature of the door panel with
a narrow outer rim and no connecting center member
requires the support provided by the glass door.
After the door panel installation is complete, apply the
cover patches or plugs provided over the holes on the
inside surface of the door.
The cover patches or plugs are part of the insulation
system on the door of the wine storage unit. Be sure to
cover all the holes in the door that were used.
The wine storage unit door is made with a sealed
double wall tempered glass core. The drill must not
contact this core when drilling. Be sure the hole is
centered on the small groove in the front of the door
frame and the drill passes squarely through the frame.
If you are inexperienced with drilling, fasten the handle
from the rear of the door panel only.

inge Adjustment
I PORTANT NOTE: The wine storage unit must be
installed and leveled before door hinge adjustments can
be made.
The top and bottom cabinet hinges on models 424G and
424FSG are held in place with three permanent adjust-
ment screws and two shipping screws. Refer to the illus-
trations below. The shipping screws must be removed and
discarded to adjust the door alignment and fit. If no
adjustments are necessary, it is recommended that all five
screws remain in place.
On the model 424FSG, only the bottom door hinge can be
adjusted. Remove and discard the two shipping screws
and loosen the three hinge screws to adjust the door.
Models 424G and 424FSG Installation 15
subzero.com
Complete the Installation
When you have completed installation of the model 424G
or 424FSG wine storage unit, refer to page 54 for an
installation checklist and page 55 for service information.
TOP DOOR HINGE
SHIPPING
SCREWS
Top hinge. Bottom hinge.
BOTTOM
DOOR HINGE
SHIPPING
SCREWS

Models 427G and 427RG Installation 16
Models 427G and 427R
OVERALL DI ENSIONS
ODEL 427G ODEL 427RG
WIT BULK STORAGE DRAWERS
27" (686)
14"(356)
13/16"
(21)
80"
(2032)
OPENING
HEIGHT
24" (610)
789/16"
(1995)
815/16"
(227)
4"
(102)
HEIGHT DIMENSIONS ± 1/2"(13)
24"
(610)
DIMENSIONS WILL VARY WITH PANEL THICKNESS
251/2"
(648)
45/8"
(117)
27" (686)
14"(356)
13/16"
(21)
341/2"
(876)
203/8"
(518)
101/4"
(260)
131/4"
(337)
1/2"
(13)
3/8"
(10)
80"
(2032)
OPENING
HEIGHT
24" (610)
789/16"
(1995)
93/4"
(248)
4"
(102)
HEIGHT DIMENSIONS ± 1/2"(13)
24"
(610)
DIMENSIONS WILL VARY WITH PANEL THICKNESS
191/2"
(495)
251/2"
(648)
45/8"
(117)
Overall dimensions do not include panels or handles.

Models 427G and 427RG Installation 17
subzero.com
Models 427G and 427RG Installation
Make sure that the finished rough opening where the wine
storage unit is to be installed is properly prepared. Refer
to the opening dimensions illustrations for models 427G
and 427R on the previous page.
I PORTANT NOTE: The floor under the wine storage unit
must be at the same level as the surrounding finished floor
to allow for removal of the unit for servicing.
I PORTANT NOTE: To operate properly, the door must
open a minimum of 90°. Use a minimum 2" (51) filler in
corner installations to assure a 90° door opening. Allow
enough clearance in front of the unit for full door swing.
I PORTANT NOTE: The inside edges of the rough
opening, as well as the sides and a portion of the
backside of the decorative panels will need to be finished,
as they will be exposed when the doors are open.
TOOLS AND ATERIALS REQUIRED
•Appliance dolly able to support 500 lbs (227 kg) and
adequate manpower to handle the weight of the unit.
•Phillips and slotted screwdrivers.
•Allen, standard and crescent wrenches.
•Various sized pliers.
•5/16" hex bolt nut driver.
•Cordless drill and assorted drill bits.
•Level—2' (.6 m) and 4' (1.2 m) recommended.
•Masonite, plywood, pressed fiberboard, cardboard or
other suitable material to protect finished flooring.
•Appropriate materials to cover and protect the home
and furnishings during installation. I PORTANT NOTE: The depth of each integrated model is
24" (610) from the front of the unit to its back. Your design
may necessitate moving the unit back or cabinets forward to
achieve a flush fit. This will require a minimum rough opening
depth of 25" (635).
25" (635)
OPENING
DEPTH
27" (686)
OPENING WIDTH
25" (635)
OPENING DEPTH
80" (2032)
OPENING
HEIGHT
TOP VIEW
FRONT VIEWSIDE VIEW
OPENING DI ENSIONS
Do not load wine into the wine storage unit until the
installation is complete.

Models 427G and 427RG Installation 18
Electrical Requirements
For models 427G and 427RG, the electrical supply should
be located within the shaded area shown in the illustration
below. Follow the National Electrical Code and local codes
and ordinances when installing the receptacle. A separate
circuit, servicing only this appliance is required. A ground
fault circuit interrupter (GFCI) is not recommended and
may cause interruption of operation.
I PORTANT NOTE: For models 427G and 427RG, the
electrical outlet must be placed so the grounding prong is
to the right of the thinner blades. The outlet must be flush
with the back wall.
Electrical Requirements
Power Supply 115 V AC, 60 z
Circuit Breaker 15 amp
Receptacle 3-prong grounding-type
Do not use an extension cord or two-prong adapter.
Do not remove the power supply cord ground prong.
The outlet must be checked by a qualified electrician
to be sure that it is wired with the correct polarity. Verify
that the outlet is properly grounded.
13" (330)
1/4"
(6)
41/2"
(114)
LEFT SIDE
OF OPENING
FLOOR
21/2"
(64)
FRONT VIEW
Location of electrical supply.

Models 427G and 427RG Installation 19
subzero.com
Electrical Requirements
HO E ALAR SYSTE
If a home alarm system is to be used, refer to wiring
connections on page 24. In addition to operating power,
the installer may also be required to supply a home
automation system lead to the unit. This is for a low-
voltage, low-current signal similar to door and window
sensor signals. Common, normally open and normally
closed contact configurations are provided.
Three 1/4" female spade connectors are located in the
compressor compartment and are accessible behind the
kickplate/grille on models 427G and 427R. A minimum of
36" (914) of lead wire should be provided for each contact,
exiting the back wall near the electrical outlet.
An anti-tip bracket and hardware is provided with the wine
storage unit. The anti-tip bracket must be installed on a
solid base to prevent tipover in case several loaded wine
shelves are extended at the same time.
If you are installing the model 427G or 427RG in a space
deeper than 24" (610), the anti-tip bracket must be
installed no more than 24" (610) deep, so it engages the
unit properly. It is important that this measurement be
made from the front of the unit without panels, to the back
of the anti-tip bracket.
I PORTANT NOTE: In some installations the subflooring
or finished floor may require angling the wood screws
used to fasten the anti-tip bracket to the back wall.
Anti-Tip Bracket Installation
ake sure there are no electrical wires or plumbing
in the area which the screws could penetrate.
To prevent the unit from tipping forward and provide
a stable installation, the unit must be secured in place
with the anti-tip bracket provided with the unit.

Models 427G and 427RG Installation 20
Anti-Tip Bracket Installation
WOOD FLOOR APPLICATIONS
Use the six #12 x 21/2" wood screws and the six 1/4" flat
washers provided. Drill pilot holes 3/16"(5) diameter
maximum, and make sure the screws penetrate through
the flooring material and into the wall plate a minimum of
3/4"(19). Make sure the screws hold tight. Refer to the
illustration below.
CONCRETE FLOOR APPLICATIONS
Use the two 3/8" x 33/4" concrete wedge anchors, two
#12 x 21/2" wood screws and two 1/4" flat washers
provided. Make sure the anchors and screws hold tight.
Refer to the illustration below.
Anti-Tip Bracket Placement A
Wood Floor 131/2"(343)
Concrete Floor 131/2"(343)
A
A
SUBFLOORING
WOOD FLOOR
WALL PLATE
FINISHED
FLOORING
A
A
SUBFLOORING
CONCRETE
FLOOR
WALL PLATE
FINISHED
FLOORING
11/2"(38)
min
Wood floor. Concrete floor.
INSTALL CONCRETE WEDGE ANCHORS:
1) Drill a 3/8"(10) diameter hole any depth exceeding the
minimum embedment. Clean the hole or continue
drilling additional depth to accommodate drill fines.
Use a carbide drill bit manufactured within ANSI
B94.12-77.
2) Assemble the washer and nut flush with the end of
anchor to protect threads. Drive the anchor through the
material to be fastened until the washer is flush with
the surface material.
3) Expand the anchor by tightening the nut 3–5 turns past
hand-tight position or to 25 foot-pounds of torque.
Always wear safety glasses and use other necessary
protective devices or apparel when installing or
working with anchors.
Anchors are not recommended for use in lightweight
masonry material such as block or brick, or for use in
new concrete which has not had sufficient time to cure.
The use of core drills is not recommended to drill holes
for the anchors.