Sullivans Sew & Go User manual

Many thanks for your purchase!
Please nd the instructions for setting up your
Sew & Go Table.
Step #1: Basic Set Up (Figure 1)
• Remove board “H”. (Figure 1A)
• Carefully cut the strap tie used to hold the leg
assembly during shipping. (Figure 1B)
• Using a Phillips screwdriver and the screws
provided, attach the two wheel sets into the
pre-drilled holes on part “F”. (Figure 1C)
Sew & Go Sewing Table
Adjustable Height – Foldable
Instructions
Step #2: Leg Height Adjustment if Used at Seated
Height (Figure 2)
• Press in the push pin (Figure 2A) and insert
part “E” leg assembly into part “D”. (Figure 2A)
Repeat on each side.
• Center Tensioning Tube.
• Once the height is selected then take part “A”
and insert into part “B”. Once inserted use
the push-pin to lock part “A” into part “B”.
(Figure 2B) Always extend to the maximum
allowable hole. THIS ADJUSTMENT WILL VARY
DEPENDING ON THE HEIGHT OF THE TABLE.
Step #3: Individual Fine Leg Adjustment (Figure 2C)
• Remove the foot cover. Using a screwdriver raise
or lower according to oor conditions.
Figure 1A
Figure 2A
Figure 2B
Figure 2C
Item # 39276
Figure 1
Figure 2
Figure 1B
Figure 1C

Step #4: Adjusting Machine Bed (Figure 3)
•The height of the machine bed can be adjusted
by tightening or loosening the adjustment with
the Allen screws on the top of part “G”.
(Figure 3A)
•At the inside corners of machine bed there are 6
steel brackets under the tabletop part “G”.
Pull these brackets to hold the insert part “H”.
(Figure 3B)
Figure 3
If you have any questions you can contact our
helpline via email
[email protected]
or
toll free 800-862-8586.
Figure 3B
Figure 3A
Safety:
This table is not a toy – do not let children play on, under or around it. Do not place more than 30 pounds on the table. Never rest a hot iron
directly on the surface.
Cleaning:
Using a sponge or soft cloth with mild soap. Do not use any abrasive cleaners or pads.
Sullivans USA
4341 Middaugh Ave
Downers Grove, IL 60515
M.T. Sullivans & Co. Pty.Ltd.
40 Parramatta Road Underwood, Brisbane, Queensland Australia
Sullivans Enterprises (N.Z) Ltd.
28 Sir William Ave.
East Tamaki, Auckland New Zealand
Sullivans USA Inc. will replace any missing or defective parts within 30 days of purchase. Fax or email a dated receipt to 630-435-1532, along
with your request. This policy does not apply to damages due to shipping. For further assistance, please call 800-862-8586. Some restrictions
apply. See website for details.
Item # 39276

Item # 39276
Sullivans Sew & Go Table
Travel Instructions
3. Your Sullivans Sew & Go Table
is ready for travel.
2. Release the table legs using the
push pins and rotate the center
bar to slide it between your table
surface and Part F, the machine
bed.
1. Flip your table over and locate
the center bar.
To keep the Sullivans Sew & Go Table legs secure while traveling, follow these steps.
If you have any questions, you can contact us at
[email protected]
or
toll free 800-862-8586.

DO NOT RETURN
TO THE STORE
800.862.8586
PLEASE CALL US AT
FOR ASSISTANCE WITH MISSING OR REPLACEMENT
PARTS, INSTALLATION, OR INFORMATION
4341 MIDDAUGH AVENUE • DOWNERS GROVE, IL 60515 • ORDERS: 800.862.8586 • FAX: [phone]
www.sullivansusa.net www.sullivansusa.net