Sumake SA-22015T User manual

1
Operation Manual
SA-22015T, SA-22030T, SA-22050T
Read this manual before use
This hook was used for hang,
not to lock tightly.
Always attached a
secondary support
cable or chain.
Turn CW. ( )
For increasing the
spring tension by
allen key.
To loose the two
screw and tighttn, to
adjust the wire
Turn CW.( )
For decreasing about 1.0cm
(Keep the allen key and turn
slowly, even don’t adjust
under its capacity)
A sling, suspend
the tool here.
SA-22015T(22030T)(22050T)-I-2209C-YM

2
Caution
Prohibition
Incorrect use of the spring balancer
could cause personal injury.
Observe instruction in the manual and
use the balancer correctly.
Never stand under the spring
balancer.
Prohibition of disassembly.
Never put the spring balancer
in fluid.

3
1. Take the tools off while remove the spring balancer, prevent the devise drop down.
2. Please remove the spring balancer and tools if rest for a long time.
3. Remove the spring balancer and devise before arranging the tension.
Application area:
Indoor and normal atmospheric conditions. Temperature range : -10℃~ +40℃
Don’t twist and rub the cordage with cable
during travel.
Don’t load over its capacity.
Large angle using will debase the wire
rope's life, Under ±20∘is better.

4
Leave some slack in the secondary
support cable or chain to allow the
balancer to rotate freely.
The slack must be a suitable length so
that the balancer will stop within 10cm
when falling in case of failure of the
hanger or the fitting.

5
Model
Capacity
Weight
Travel
SA-22015T
0.5 –1.5 kg
1.8 kg
1.4 m
SA-22030T
1.5 –3.0 kg
1.9 kg
1.4 m
SA-22050T
3.0 –5.0 kg
2.1 kg
1.4 m
1. Installation
(1)Attached the spring balancer to the steady place.
(2)Please attached a secondary support cable and install to the steady position.
(3)Install the devise within the capacity to the bottom hook.
(4)Please adjust the tension within the capacity after install the devise.
2. Checks before use
(1)The hanger and bottom hook is steady and turn swivel.
(2)The cable is complete.
(3)The ratchet spring and spindle is steady.
(4)The appearance is complete, no any damage.

ECDECLARATION OF CONFORMITY
We: SUMAKE INDUSTRIAL CO., LTD.
4F, No. 351, Yangguang St., Neihu District, Taipei City, Taiwan
declare in sole responsibility that the equipment
Equipment：AIR PU HOSE BALANCER
Model/ Serial No.：SA-22015T(22030T)(22050T)
to which this declaration applies, complies with these normative documents:
Machinery Directive: 2006/42/EC
and conforms to the following EN standard,
EN ISO 12100: 2010
Name and Signature/Position Date and Place
2013/2/22
MikeSu–ManagingDirector Taipei, Taiwan
SA-22015T(22030T)(22050T)-D-1308C-YMF

SA-22015T AIR PU HOSE BALANCER (0.5-1.5KG)
SA-22030T AIR PU HOSE BALANCER (1.5-3.0KG)
SA-22050T AIR PU HOSE BALANCER (3-5KG)
PARTS LIST
No. Parts No. Description Q'ty
1 SA22030T-01 Spindle 1
2 SA22030T-02 Screw 1
3 SA22030T-03 Ratchet 1
4 SA22030T-04 Ratchet Spring 1
Spring Plate Set [Incl. 13, 14, 15]
[SA-22015T]
Spring Plate Set [Incl. 13, 14, 15]
[SA-22030T]
Spring Plate Set [Incl. 13, 14, 15]
[SA-22050T]
16 SA22030T-16 Spring Cover 1
17 SA22030T-17 Screw 3
33 SA22030T-33 Cover 1
35A SA22030T-35A Joint 1
36 SA22030T-36 Spanner Key 6 mm 1
37 SA22030T-37 C-Ring 1
38 SA22030T-38 Safety Loop 1
39 SA22030T-39 Screw 4
40 SA22030T-40 Rivet 1
SA-22015T(22030T)(22050T)-P-2306F-YM
6~-12
13~15
SA22015T-13
SA22030T-13
SA22050T-13
Hose Assembly [Incl. 18, 19(2), 20, 21(2), 22, 23,
24, 25, 26, 27, 28, 29, 30(3), 31, 32]
18~32
SA22030T-18
1
1
SA22030T-11S
Casing Set [Incl. 6, 7, 8, 9, 10, 11, 12]
1
1
1

NOTE
www.SUMAKE.com
www.aircompressors.com.tw