Sumake SA-22030 User manual

1
Operation Manual
SA-22030, SA-22050, SA-22070
Read this manual before use
Do not fasten the hanger
Always attached a
secondary support
cable or chain.
Turn CW. ( )
For increasing the
spring tension by
allen key.
When the spring
breaks, the sage pin
pops out from the
spring case and
collides with one of
the pins, to stop the
drum rotating.
Turn CW.( )
For decreasing about 1.0cm
(Keep the hex and turn
slowly, even don’t adjust
under its capacity)
Bottom hook
SA-22030(22050)(22070)-I-2206H-YM

2
Caution
Prohibition
Incorrect use of the spring balancer
could cause personal injury.
Observe instruction in the manual and
use the balancer correctly.
Never stand under the spring
balancer.
Prohibition of disassembly.
Never put the spring
balancer in fluid.

3
1. Take the tools off while remove the spring balancer, prevent the devise drop down.
2. Please remove the spring balancer and tools if rest for a long time.
3. Remove the spring balancer and devise before arranging the tension.
Application area:
Indoor and normal atmospheric conditions. Temperature range : -10℃ ~ +40℃
Don’t twist and rub the cordage with cable
during travel.
Don’t load over its capacity.
Large angle using will debase the wire
rope's life, Under ±20∘is better.

4
Leave some slack in the secondary
support cable or chain to allow the
balancer to rotate freely.
The slack must be a suitable length
so that the balancer will stop within
10cm when falling in case of failure of
the hanger or the fitting.

5
Model
Capacity
Weight
Travel
SA-22030
1.5 – 3.0 kg
1.73 kg
1.3 m
SA-22050
3.0 – 5.0 kg
1.82 kg
1.3 m
SA-22070
5.0 – 7.0 kg
1.85 kg
1.3 m
1. Installation
(1)Attached the spring balancer to the steady place.
(2)Please attached a secondary support cable and install to the steady position.
(3)Install the devise within the capacity to the bottom hook.
(4)Please adjust the tension within the capacity after install the devise.
2. Checks before use
(1)The hanger and bottom hook is steady and turn swivel.
(2)The cable is complete.
(3)The ratchet spring and spindle is steady.
(4)The appearance is complete, no any damage.

EC DECLARATION OF CONFORMITY
We: SUMAKE INDUSTRIAL CO., LTD.
4F, No. 351, Yangguang St., Neihu District, Taipei City, Taiwan
declare in sole responsibility that the equipment
Equipment：SPRING BALANCER
Model/ Serial No.：SA-22030(22050)(22070)
to which this declaration applies, complies with these normative documents:
Machinery Directive: 2006/42/EC
and conforms to the following EN standard,
EN ISO 12100: 2010
Name and Signature/Position Date and Place
2022/12/1
Mike Su –Managing Director Taipei, Taiwan
SA-22030(22050)(22070)-D-2306E-YMF

SA-22030 SPRING BALANCER
(
1.5-3KG
)
SA-22050 SPRING BALANCER
(
3-5KG
)
SA-22070 SPRING BALANCER
(
5.0-7.0KGS
)
PARTS LIST
No. Parts No. Description Q'ty
1 SA22030-01 Spindle 1
2 SA22030-02 Screw 1
3 SA22030-03 Ratchet 1
3A SA22030-03A Ratchet Spring 1
SA22030-13S Spring Plate Set [Incl. 11, 13] [SA-22030] 1
SA22050-13S Spring Plate Set [Incl. 11, 13] [SA-22050] 1
SA22070-13S Spring Plate Set [Incl. 11, 13] [SA-22070] 1
12 SA22030-12 Screw 1
14 SA22030-14 Spring Cover 1
15 SA22030-15 Screw 6
17 SA22030-17 Cover 1
20 SA22030-20 Hex Spanner / rod 1
SA-22030(22050)(22070)-P-1510G-YM
11&13
4~10
16~19
SA22030-09AS Casing Set [Incl. 4, 5, 6, 7, 8, 9A, 10] 1
SA22030-19S Cable Set [Incl. 16(2), 18, 19] 1

NOTE
www.SUMAKE.com
www.AIRCOMPRESSOR.com.tw