Sumake HBPFH080 User manual

.
SUMAKE PNEUMATIC TOOLS
High Torque Oil Free Pistol Handle
Air Shut Off Composite Screwdriver
SUMAKE INDUSTRIAL CO., LTD
4F,NO.351,Yangguang St.,Neihu District TAIPEI, TAIWAN, ZIP:114-91
Specification:
Noise and Vibration:
Remark
MODEL
Free
Speed
Torque range
(±3%)
Min. air hose
bore (mm)
Vibration
EN ISO 28927-2
Noise
EN ISO 15744
r/min
Nm
Kgf-cm
6kg/cm²
5kg/cm²
Sound pressure level
Sound power level
HBPFH080
550
1-8
10-80
6.0
6.35
No Load: 1.5 m/s²
No Load: 78.1 dB(A)
No Load: 89.1 dB(A)
Please always wear
ear protector at
environment noise
level > 80 dB(A)
due to risk of
impaired hearing!
HBPFH080H
2200
2-8
20-80
8.0
9.5
No Load: 1.5 m/s²
No Load: 78.1 dB(A)
No Load: 89.1 dB(A)
HBPFH110
1200
2-11
20-110
8.0
9.5
No Load: 1.6 m/s²
No Load: 79.1 dB(A)
No Load: 90.1 dB(A)
HBPFH180
650
7-18
70-180
8.0
9.5
No Load: 1.5 m/s²
No Load: 81.3 dB(A)
No Load: 92.3 dB(A)
HBPFH250
430
5-25
50-250
8.0
9.5
No Load: 1.7 m/s²
No Load: 80.3 dB(A)
No Load: 91.3 dB(A)
Recommend Air Pressure: 6.0 kg/cm²
Uncertainty
K= 1.5 m/s²
Uncertainty K= 3dB
HBPFH080(080H)(110)(180)(250)-S-2303E-MIF

EC DECLARATION OF CONFORMITY
We: SUMAKE INDUSTRIAL CO., LTD.
4F, No. 351, Yangguang St., Neihu District, Taipei City, Taiwan
declare in sole responsibility that the equipment
Equipment：PISTOL TYPE PISTOL HANDLE AIR SHUT OFF COMPOSITE SCREWDRIVER
Model/ Serial No.：HBPFH080(080H)(110)(180)(250)
to which this declaration applies, complies with these normative documents:
Machinery Directive: 2006/42/EC
and conforms to the following EN standard,
EN ISO 12100: 2010
EN ISO 11148-6:2012
Name and Signature/Position Date and Place
2022/12/1
Mike Su –Managing Director Taipei, Taiwan
HBPFH080(080H)(110)(180)(250)-D-2303C-MIF

OPERATION MANUAL
AIR SUPPLY
1. Air tools are adversely affected by moisture. Since air from compressor contains much moisture and dust, it is desirable to provide a filter in
the pipeline to remove such undesirable elements. Also take the drain out from air tank every day.
2. When using brand-new air hose or air pipe, blow and clean the air hose or pipe inside before installation.
3. Keep air hose or air pipe inside clean to prevent airdrop problem caused by lots of drain and dust accumulated, either to avoid possibly
inside diameter smaller problem after long term usage.
4. When disconnect air hose from air tool during operation, do not drop air hose end to the floor as dust or other element may get into air hose.
5. Use air regulator to keep stable air pressure at 6.0kgf-cm²( 80~90 psi) at the toll. It is important to get proper air pressure at the toll.
6. With high quality Oil-free motor, any moisture or lubrication injection may damage the air screwdriver, please keep tool dry and avoid oil
based substances exposing to the products. For avoiding moisture affection, using Air Dryer is necessary in wet area or under moist
weather.
Common Troubleshooting:
Appearance
Possible Cause
Solution
WHEN AIR INTO AIR INLET, THE TOOL
CANNOT WORK
Operating rod has worn and tore or bend.
Disassemble and repair
Spring is in right position
Disassemble and repair
Parts front plate, rotor, cylinder, end plate are rusty.
Disassemble and repair
Parts 15t plant gear, 15t plant gear, fifth gear cage and main
gear, fifth ear cage, internal gear, blade are broken.
Disassemble and repair
WHEN AIR INTO AIR INLET, THE TOOL
RUN WITHOUT PRESS THE TRIGGER
Some of O-rings are loaded or deformed
Disassemble and repair
NON AUTO SHUT-OFF WHEN TORQUE
IS REACHED
Some of O-rings are worn and tore.
Disassemble and repair
Spring (inside of anvil) may not in right position
Disassemble and repair
Parts slide base, rear clutch, bearing, center clutch, retainer,
bushing have worn and tore.
Disassemble and repair
THE MAX TORQUE IS INSUFFICIENT.
Parts front plate, rotor, cylinder, end plate, ball bearing are
rusty.
Disassemble and repair
Motor of blades are worn and tore.
Disassemble and repair
Rear clutch is worn and tore.
Disassemble and repair
Torque spring is elastic fatigued.
Disassemble and repair
WHEN THE FREE SPEED IS TOO LOW
Air pressure may not enough.
Check equipment.
Check air inlet set.
Disassemble and repair
HBPFH series-I-1910E-MI

HBPFH080H
HBPFH080H-P-1203A-MI
HIGH TORQUE OIL FREE PISTOL HANDLE AIR SHUT OFF COMPOSITE SCREWDRIVER

HBPFH080H
PARTS LIST
No. Parts No. Description Q'ty No. Parts No. Description Q'ty
1 5L2100 Pistol Housing (Green) 1 42 3S5231 Ball Race 1
2 2C2002 Blank Cap 1 43 6N2006 C Ring 1
2-1 7Q2008 O Ring 1 44 3S5032 Anvil [PULL] 1
2-2 7S2106-1 Screw 1 44-1 7Q2002 Regulate Screw 1
2-3 7S2156 Screw 4 45 7S2105 Ball 2
3 7Q2006 O Ring 1 46 6N5110 Spring 1
4 7Q6112 Valve O-Ring 1 47 3S2227 Slide Base 1
5 6S2023 Valve Pin 1 48 6N5002 Torque Spring 1
6 6N2106 Cone Spring 1 49 2S5121 Washer 1
7 6S2024 Valve Bushing 1 50 3S2101 Bushing 1
7-1 7Q2009 O-Ring 2 51 2S2241 Anvil Bushing 1
8 5L2116 Cap (Black) 2 52 3A5202 Clutch Housing 1
9 5L2701 Button (Black) 1 52-1 2Q2003 O Ring 1
10 7Q2011 Valve O-Ring 1 53 6S2010 Needle Pin 3
11 6S6104 Valve 1 54 3S5101 Regulation Washer 1
11-1 6N5006 Spring 1 55 3A6001 Torque Ring 1
12 7S2107 Set Screw And Washer 1 56 7S3107 Ball 1
13 2L6026 Switch (Iron) 1 56-1 3S2122 Bushing 1
14 7S5001 Ball Bearing 1 57 5S2009 Bit Slide Sleeve [PULL] 1
15 1S6001-A End Plate 1 58 6N2003 Spring 1
16 1P6005 Cylinder 1 58-1 2S2109 Washer 1
16-1 2S2023 Key 1 59 6N2001 C Ring 1
18 1S6041 Rotor 1 60 5A3212 Housing Cap 1
19 1P6052 Oil-Free Blade 6 61 5A6516 Torque Cover (Black) 1
20 1P6063 Front Plate 1 62 6S2005 Operating Rod 1
21 7S2002 Ball Bearing 1 63 7Q2006 O Ring 1
22 6N2020 C Ring 1 64 6S2021 Valve Plate 1
25 1P6123 15T Plate Gear 3 65 6N2107 Cone Spring 1
26 1P6302 Seventh Gear Cage 1 66 2Q5001 O Ring 2
27 1S3053 Connect 1 67 2S2011 Screw Cap 2
28 1S3201 Internal Gear Washer 1 68 2P3040 Silencer 2
30 1S3158 First Internal Gear 1 69 5L2204 Pistol Cover (Black) 1
30-1 2S2201 Washer 2 70 2Q2003 O Ring 1
31 5A6041 Front Housing 1 71 2P3029 Base For Pistol 1
32 7S6003 Ball Bearing 1 72 2P3030 Silencer 1
33 2S6103 Retainer 1 73 2P3032 Silencer For Pistol 1
34 7S2102 Ball 32 74 2Q5001 O Ring 1
35 3S5001 Pilot Pin 1 2S2068 Air Inlet Bushing [PT] 1
36 3S5211 Rear Clutch 1 2S2069 Air Inlet Bushing [NPT] 1
37 6N2006 C Ring 1 77 6N6001 Spring 1
38 3S5217 Center Clutch 1 78 7S2111 Screw 1
39 7S2112 Ball 2 79 7S2102 Ball 2
40 3S5221 End Clutch 1 80 7S2111 Screw 1
41 7S2102 Ball 25 HBPFH080H-P-1203A-MI
HIGH TORQUE OIL FREE PISTOL HANDLE AIR SHUT OFF COMPOSITE SCREWDRIVER
76