Sun microsystems Netra t1 series User manual

Netra™t1 Model 105 Installation

Guide

Part 2

Safety Precautions

For your protection, observe the following safety precautions when setting up

your equipment:

•Follow all cautions and instructions marked on the equipment.

•Never push objects of any kind through openings in the equipment.

Dangerous voltages may be present.

Conductive foreign objects can produce a short circuit that could cause fire,

electric shock, or damage to your equipment.

Symbols

The following symbols may appear in this poster:

Caution – There is a risk of personal injury and equipment damage.

Follow the instructions.

Caution – Harzardous voltages are present. To reduce the risk of

electric shock and danger to personal health, follow the instructions.

Modifications to Equipment

Do not make mechanical or electrical modifications to the equipment. Sun

Microsystems is not responsible for the regulatory compliance of a modified

product.

806-1552-10-A.doc Page 1 Tuesday, July 27, 1999 12:39 PM

Black spot plate

Netra™t1 Model 105 Installation

Guide

Part 2

Safety Precautions

For your protection, observe the following safety precautions when setting up

your equipment:

•Follow all cautions and instructions marked on the equipment.

•Never push objects of any kind through openings in the equipment.

Dangerous voltages may be present.

Conductive foreign objects can produce a short circuit that could cause fire,

electric shock, or damage to your equipment.

Symbols

The following symbols may appear in this poster:

Caution – There is a risk of personal injury and equipment damage.

Follow the instructions.

Caution – Harzardous voltages are present. To reduce the risk of

electric shock and danger to personal health, follow the instructions.

Modifications to Equipment

Do not make mechanical or electrical modifications to the equipment. Sun

Microsystems is not responsible for the regulatory compliance of a modified

product.

806-1552-10-A.doc Page 1 Tuesday, July 27, 1999 12:39 PM

Blue spot plate

Refer to panel 9 for more information.

1Remove the front bezel by squeezing the latches at each end.

2Disassemble the system and remove the PCI card (if fitted) as shown in

panel 5. 3Squeeze and pull out the blanking panel. 4Slide the connector card

into the slot behind the CD-ROM drive bay. 5Connect the cable to the connector

under the PCI card. 6Slide in the CD-ROM drive until the catch clicks. 7

Replace the other components in the reverse order to that in which you removed

them.

Installing the CD-ROM Drive

806-1552-10-A.doc Page 2 Tuesday, July 27, 1999 12:39 PM

Black spot plate

Refer to panel 9 for more information.

1Remove the front bezel by squeezing the latches at each end.

2Disassemble the system and remove the PCI card (if fitted) as shown in

panel 5. 3Squeeze and pull out the blanking panel. 4Slide the connector card

into the slot behind the CD-ROM drive bay. 5Connect the cable to the connector

under the PCI card. 6Slide in the CD-ROM drive until the catch clicks. 7

Replace the other components in the reverse order to that in which you removed

them.

Installing the CD-ROM Drive

806-1552-10-A.doc Page 2 Tuesday, July 27, 1999 12:39 PM

Blue spot plate

Class 1 Laser Product

Luokan 1 Laserlaite

Klasse 1 Laser Apparat

Laser Klasse 1

Caution – Use of controls, adjustments, or the performance of

procedures other than those specified herein may result in hazardous

radiation exposure.

806-1552-10-A.doc Page 3 Tuesday, July 27, 1999 12:39 PM

Black spot plate

Class 1 Laser Product

Luokan 1 Laserlaite

Klasse 1 Laser Apparat

Laser Klasse 1

Caution – Use of controls, adjustments, or the performance of

procedures other than those specified herein may result in hazardous

radiation exposure.

806-1552-10-A.doc Page 3 Tuesday, July 27, 1999 12:39 PM

Blue spot plate

Regulatory Compliance Statements

Your Sun product is marked to indicate its compliance class:

• Federal Communications Commission (FCC) — USA

• Department of Communications (DOC) — Canada

• Voluntary Control Council for Interference (VCCI) — Japan

Please read the appropriate section that corresponds to the marking on your Sun product before

attempting to install the product.

FCC Class A Notice

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may cause

undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction manual, may cause harmful interference to

radio communications. Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at his own expense.

Shielded Cables: Connections between the workstation and peripherals must be made using

shielded cables in order to maintain compliance with FCC radio frequency emission limits.

Networking connections must be made using shielded twisted-pair (TP) cables.

Modifications:Any modifications made to this device that are not approved by Sun Microsystems,

Inc. may void the authority granted to the user by the FCC to operate this equipment.

DOC Class A Notice - Avis DOC, Classe A

This Class A digital apparatus meets all requirements of the Canadian Interference-Causing

Equipment Regulations.

Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel

brouilleur du Canada.

806-1552-10-A.doc Page 4 Tuesday, July 27, 1999 12:39 PM

Black spot plate