Sunjoy A301002300 User manual

ROBSON RND WOOD
BURNING FIRE BOWL
ASSEMBLY INSTRUCTIONS
ITEM#: A301002300
SKU#:810540926
Production Number: 2021200011
ASS
EMB
L
Y INSTRUCTION
S
L
L
I
TEM#
:
A
30
1
002300
S
K
U
#
:
8
1
0
5
4
0
9
2
6
Pr
oductio
n N
u
m
be
r
:
202
1
2000
1
1

2/8
WARRANTY:
WARNINGS:
MAINTENANCE
GENERAL BEST PRACTICES FOR ASSEMBLY:
WHAT IS COVERED?
The limited warranty is extended to the original purchaser and applies to material and manufacturer’s defect provided
the item is maintained with care and used only for personal, residential purposes.
Warranty: 1 Year
• Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and
hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.
• Place all parts from the box in a cleared area and position them on the floor in front of you. Remove all packing materials and
place them back into the box. Do not dispose of the packing materials until assembly is complete.
• Some parts may contain sharp edges. Wear protective gloves if necessary during assembly.
• Pay attention to the parts orientation
• Keep fingers away from the places where they can be pinched or trapped.
• Check all screws and nuts periodically for tightness, fastening them again as required.
Lighting
• Make sure there is only a small amount of ash in the bottom of the bowl.
• Place a layer of dry seasoned hardwood that covers no more than 3/4 of the bowl.
• Use a match to light kindling or fire starter.
• Use the poker that is provided to operate. Please wear heat-resistant gloves during use. Extinguishing
• Allow fire burn itself out.
• DO NOT use water to extinguish as this is dangerous and can damage th is fire bowl.
Cleaning
• This fire bowl should be cleaned on a regular basis to promote safer experience and long product life.
• DO NOT attempt to clean this fire bowl until the fire is COMPLETELY out and cool to touch.
• DO NOT use oven cleaner or abrasive cleaner as this will damage the fire bowl.
Storage
• DO NOT move or store this fire bowl until the fire is COMPLETELY out and cool to touch.
• Store the fire bowl in a dry location to maximize product life.
• Store assembled fire bowl in a location away from children and pets.
• This fire bowl is intended for outdoor use only. NEVER LEAVE A FIRE UNATTENDED.
• DO NOT use the fire bowl to cook food. The fire bowl is not designed for grilling food.
• DO NOT allow children or pets near the fire bowl without supervision.
• DO NOT touch the surface of the fire bowl while in use as it may cause burns.
• NEVER burn in vehicles, tents or indoors. CARBON MONOXIDE HAZARD.
• Use a poker and / or heat-resistant gloves to open / close the mesh cover while in use.
• DO NOT use water to extinguish as this is dangerous and can cause damage to the fire bowl.
• Burn only untreated wood or fire logs in this fire bowl.
• DO NOT use gasoline or kerosene to start the fire in this fire bowl.
• DO NOT use this fire bowl on a wood deck, long or dry grass and / or leaves, or on a combustible surface.
• DO NOT attempt to move the fire bowl while it is hot or in use.
• Place the fire bowl no closer than 8' (2.4 m) from walls or combustibles during. use
• Adequate fire extinguishing material should be readily available.
• Always ensure that the mesh cover is secured over the fire bowl while in use.
• The poker handle may become hot during and after use.
• Check local fire regulations and municipal by-laws for information regarding the safe use of this fire bowl.

EXPLODED DRAWING


PARTS LIST
Label Part Number Description Qty Part Image
$ 3 6FUHHQ+DQGOH 
% 3 0HVK6FUHHQ 
' 3 *UDWH 
( 3 %RZO 
) 3 5LQJ 
* 3 /HJ 
+ 3 3RNHU 


HARDWARE LIST
Label Part Number Description Qty Add Part Image
$$ + 1XW0  
%% + %ROW0  
&& + )ODWZDVKHU
0  
'' + %ROW0  
:: + :UHQFK0  


HELPFUL HINTS
• Separating parts before starting
How many people needed for the installation

Tool needed 3URYLGHGLQKDUGZDUHSDFN

STEP 1
Assembled View:
7/8
Attach Leg(G) to the Bowl(E) with Bolt
M6*10(BB),Flat washerM6(CC) and
Nut M6(AA),tighten the Bolts to 100%
depth with Wrench M6(WW); Attach
Leg(G) to Ring(F) with Bolt M6*20(DD)
and Flat washer M6(CC),tighten all the
Bolts.
1x 1x
4x
8x 12x 8x
4x

Assembled View:
8/8
Attach Screen Handle(A) to Mesh Screen(B)
with Nut M6(AA); Put the Grate(D) into the
Bowl(E), then put the assembled Mesh
Screen(A/B) on the Bowl(E), and finally
match the Poker(H).The product assembly is
completed.
STEP 2
1x 1x
1x
1x
1x