Sunny Health & Fitness P8200 User manual

• •
Important Safety Information
We thank you for choosing our product. To ensure your safety and health, please use
this equipment correctly. Please read the information below carefully before using this
equipment.
1. It is important to read this entire manual before assembling and using the equipment.
Safe and effective use can only be achieved if the equipment is assembled,
maintained and used properly.
2. Before starting any exercise program you should consult your doctor to determine if
you have any medical or physical conditions that could put your health and safety at
risk, or prevent you from using the equipment properly. Your doctor’s advice is
essential if you are taking medication that affects your heart rate, blood pressure or
cholesterol level.
3. Be aware of your body’s signals. Incorrect or excessive exercise can damage your
health. Stop exercising if you experience any of the following symptoms: pain,
tightness in your chest, irregular heartbeat, extreme shortness of breath,
lightheadedness, dizziness or feelings of nausea. If you do experience any of these
conditions, you should consult your doctor before continuing with your exercise
program.
4. Keep children and pets away from the equipment. The equipment is designed for
adult use only.
5. Use the equipment on a solid, flat level surface with a protective cover for your floor
or carpet. To ensure safety, the equipment should have at least 0.5 meters of free
space all around it.
6. Before using the equipment, please make sure all the nuts and bolts are securely
tightened. Always use the equipment as indicated. If you find any defective
components while assembling or checking the equipment, or if you hear any
unusual noises coming from the equipment during use, stop immediately. Do not
use the equipment until the problem has been rectified.
7. There are many functions of the computer; the data will show when using the
equipment and will display information about your exercise routine. Please note that
the heart pulse monitor is solely to provide some reference.
8. Wear suitable clothing while using the equipment. Avoid wearing loose clothing that
may get caught in the equipment or that may restrict or prevent movement.
9. The maximum weight of user:
220LBS.
10.Care must be taken when lifting or moving the equipment so as not to injure your
back.
11.The equipment is not suitable for therapeutic use.
12.Please keep this manual and the assembling tools.
13.This equipment is designed for indoor and home use only, not intended for commercial
use.
1

EXPLODED VIEW
2

PARTS LIST
No. Description Qty. No. Description Qty.
1 Computer 1 27
End cap Φ50 2
1a Computer wire 1 1 28
Saddle 1
2 Trunk line 1 29
Washer d8*Φ16*1.5 3
3 8- Level Tension control 1 30
Nylon Nut M8 3
4 Screw M5*15 1 31
Saddle tube 1
5 Handlebar post 1 32
Stretch pipe 1
6 Arc washer d8*Φ20*2*R30 8 33
Bushing Φ50 1
7 Screw M8*16 4 34
Knob M16*1.5*22 1
8 Sensor wire 1 35
Decoration cover 1
9 Main frame 1 36
Spanner S13-14-15 1
10 Tension control wire (down
side)
1 37
Allen wrench S6 1
11 Crank 1
12 Spring washer d8 2
13 Screw M8*30 2
14 Foam grip Φ23*25*445 2
15 Arc-washer d5*Φ20*1.5*R30 1
16 Crank cover 2
17 Cover 1
18 End cap Φ25*16 2
19L/R Chain cover L/R 2
20 Handlebar 1
21 Rolling end cap Φ50 2
22 Carriage bolt M8*60 4
23 Front stabilizer 1
24 Nut M8 4
25L/R Pedal L/R 2
26 Rear stabilizer 1
3

HARDWARE PACKAGE
4

ASSEMBLY INSTRUCTIONS
Step 1:
A. Attach the Front stabilizer (23) and Rear stabilizer (26) to the Main
frame (9) fixing with the 4 sets Carriage bolt (22), Arc-washers (6) and
Nuts (24).
B. Attach the Pedals（25L/R）to the *left and right side of Crank (11).
* IMPORTANT: Left crank has reversed threading; you must screw pedal
counter-clockwise to tighten. Failure to follow installation instructions may
cause permanent damage to your bike.
5

Step 2:
Fix the Saddle (28) to the Saddle tube (31) with the Nylon nuts (30) and
Washers (29).
6

Step 3:
A. Connect the bottom of the Tension control wire (10) with the Tension
control (3) and connect the Sensor wire (8) with Trunk line (2).
*NOTE : Please make sure the Tension control (3) is at the lowest tension level before you begin.
This will ensure the wires are at their longest reaching points to make the connection easier.
B. Insert the Handlebar post (5) to the Main frame (9) fixing with 4 sets Screws
(7) and Arc-washers (6).
C. Attach the Stretch pipe (32) to the Saddle tube (31), then insert the Saddle
tube (31) to the Main frame (9) fixing with Knob (34).
7

• •
Step 4:
A. Connect the Computer wire (1a) with the Trunk line (2). Connect the
Computer (1) to the top of Handlebar post (5).
B. Fix the Handlebar (20) to the Handlebar post (5) with the Screws (13)
and Spring washer (12) and attach the Cover (17).
Assembly is complete.
Version: Apr 27th,2013