Sunny Health & Fitness SF-RW522016 User manual

MAGNETIC ROWING MACHINE SMART
ROWER WITH BLUETOOTH
SF-RW522016
USER MANUAL
IMPORTANT! Please retain owner’s manual for maintenance and adjustment instructions. Your satisfaction is
very important to us,PLEASE DO NOT RETURN UNTIL YOU HAVE CONTACTED US:
[email protected] or 1- 877 - 90SUNNY (877-907-8669).

1
IMPORTANT SAFETY INFORMATION
We thank you for choosing our product. To ensure your safety and health, please use this
equipment correctly. It is important to read this entire manual before assembling and using the
equipment. Safe and effective use can only be achieved if the equipment is assembled, maintained,
and used properly. It is your responsibility to ensure that all users of the equipment are informed of
all warnings and precautions.
1. Before starting any exercise program, you should consult your physician to determine if you
have any medical or physical conditions that could put your health and safety at risk or prevent
you from using the equipment properly. Your physician’s advice is essential if you are taking
medication that affects your heart rate, blood pressure, or cholesterol level.
2. Be aware of your body’s signals. Incorrect or excessive exercise can damage your health. Stop
exercising if you experience any of the following symptoms: pain, tightness in your chest,
irregular heartbeat, shortness of breath, lightheadedness, dizziness, or feelings of nausea. If
you do experience any of these conditions, you should consult your physician before continuing
with your exercise program.
3. Keep children and pets away from the equipment. The equipment is designed for adult use
only.
4. Use the equipment on a solid, flat level surface with a protective cover for your floor or carpet.
To ensure safety, the equipment should have at least 2 feet (60 CM) of free space all around it.
5. Ensure that all nuts and bolts are securely tightened before using the equipment. The safety of
the equipment can only be maintained if it is regularly examined for damage and/or wear and
tear.
6. Always use the equipment as indicated. If you find any defective components while assembling
or checking the equipment, or if you hear any unusual noises coming from the equipment
during exercise, discontinue use of the equipment immediately and do not use until the
problem has been rectified.
7. Wear suitable clothing while using the equipment. Avoid wearing loose clothing that may
become entangled in the equipment.
8. Do not place fingers or objects into the moving parts of the equipment.
9. The maximum weight capacity of this unit is 250 pounds (110KG).
10. This equipment is not suitable for therapeutic use.
11. To avoid bodily injury and/or damage to the product or property, proper lifting and moving are
required.
12. Your product is intended for use in cool and dry conditions. You should avoid storage in
extreme cold, hot or damp areas as this may lead to corrosion and other related problems.
13. This equipment is designed for indoor and home use only; it is not intended for commercial
use.

2
PRE-ASSEMBLY CHECK LIST
Before you start to assemble, please make sure all parts are included.
No.
Description
Spec.
Qty.
No.
Description
Spec.
Qty.
44 Main Frame 1 13 Computer 1
62 Sliding Rail 1 A Hardware Package 1
1 Front Stabilizer 1 B Hardware Package 1
69 Rear Stabilizer 1 C Thank You Card 1
71 Seat 1 D Manual
1
67 Computer Support 1 E AAA Battery 2
49L/R Pedal L/R 2

3
HARDWARE PACKAGE

4
HARDWARE PACKAGE
Ordering Replacement Parts (U.S. and Canadian Customers only)
Please provide the following information in order for us to accurately identify the part(s) needed:
The model number (found on cover of manual)
The product name (found on cover of manual)
The part number found on the “EXPLODED DIAGRAM” and “PARTS LIST” (found near the front of
the manual)
Please contact us at [e-mail] or 1- 877 - 90SUNNY (877-907-8669).

5
ASSEMBLY INSTRUCTIONS
We value your experience using Sunny Health and Fitness products. For assistance with parts or
troubleshooting, please contact us at [e-mail] or 1-877-90SUNNY (877-907-
8669).
STEP 1:
Attach Front Stabilizer (No. 1) to
Main Frame
(No. 44) using 2 Bolts (No. 3) and 2 Washers
(No. 2). Tighten and secure with Allen Wrench
(No. 80).
STEP 2:
Attach the 2 Bolts (No. 48) into the bottom hole
in position B of Main Frame (No. 44), with
Spanner (No. 78).
Insert the 2 Bolts (No. 48) into the upper hole in
position A of the Main Frame (No. 44) through
the 2 Pedals (No. 49L/R). Tighten with Spanner
(No. 78).
NOTE: The 2 Pedals (No. 49L/R) should rest on
Bolts (No. 48) that are in position B.

6
We value your experience using Sunny Health and Fitness products. For assistance with parts or
troubleshooting, please contact us at [e-mail] or 1-877-90SUNNY (877-907-
8669).
STEP 3:
Insert the Seat (No. 71) onto
Sliding Rail (No.
62).
Insert the Limit Axle (No. 66) into the hole on the
back of the Sliding Rail (No. 62).
Attach the Limit Mat (No. 65) onto the Limit
Axle (No. 66) using 1 Screw (No. 63) and 1
Washer (No. 64), then tighten with Spanner (No.
81).
STEP 4:
Attach Sliding Rail (No. 62) onto Rear Support
(No. 69) using 4 Screws (No. 72), 4 Spring
Washers (No. 52), and 4 Washers (No. 2).
Tighten and secure with Allen Wrench (No. 80).
STEP 5:
Attach the Sliding Rail (No. 62) to Main Frame
(No. 44) using 1 Bolt (No. 58) and 1 Screw (No.
59). Tighten and secure with Allen Wrench (No.
79) and Allen Wrench (No. 80).
Next, secure Sliding Rail (No. 62) to the Main
Frame (No. 44) using 1 Knob (No. 47) and 1
Washer (No. 46), then insert Pull Pin (No. 60).

7
We value your experience using Sunny Health and Fitness products. For assistance with parts or
troubleshooting, please contact us at [e-mail] or 1-877-90SUNNY (877-907-
8669).
STEP 6:
Remove 4 Screws (No. 37) from the back of the
Computer (No. 13)with the Spanner (No. 81).
First insert Couputer Wire A/B (No.13A/B) though
Computer Support (No. 67), then attach the
Computer (No. 13)to the Computer Support
(No. 67) using 4 Screws (No. 37)
that were
removed. Tighten and secure with
Spanner (No.
81).
Connect the Sensor Wire A (No. 45A)
to the
Computer Wire B (No. 13B) and connect the
Sensor Wire B (No. 45B) to the Computer Wire A
(No. 13A). Next, insert the connected wire into Main
Frame (No. 44).
Attach the Computer Support (No. 67) to Main
Frame (No. 44) using 2 Bolts (No. 61) and 2
Spring Washers (No. 52). Tighten and secure
with Allen Wrench (No. 80).

8
ADJUSTMENTS &USAGE GUIDE
CAUTION! Moving parts, such as the seat, can cut and crush. Keep hands clear of the sliding rail
during use!
PEDAL STRAP ADJUSTMENT
The pedal straps
is adjustable and can be
personalized to fit the user’s foot size.
NOTE: To avoid injury, please adjust
the pedal
straps to user’s foot before exercise.
MOVING THE ROWER
To move the rower, lift up the Rear Support (No.
69) until the transportation wheels on the Front
Stabilizer (No. 1) touch the ground.
With the
transportation
wheels on the ground, you can
transport the rower to the desired loc
ation with
ease.
ADJUSTING THE BALANCE AND RESISTANCE
Adjust the End Caps (No. 70) on the rear support
of the rower if the rower is unbalanced during use.
Rotate the Tension Control Knob (No. 14)
clockwise to increase
the level of resistance.
Rotate the Tension Control Knob (No. 14)
counter-clockwise to decrease
the level of
resistance.
Tension levels are set at Level 1 being the lowest
and Level 8 being the highest.

9
FOLDING GUIDE
CAUTION!
Use caution when you
vertically fold the
Sliding Rail (No. 62)
as your head may
touch the Rear
Support (No. 69).
CAUTION!
The Seat (No. 71)
will
glide down
when folding the
Sliding Rail (No.
62)!
When not in use, you can
save space by folding the
Sliding Rail (No. 62).
Disassemble Knob (No.
47) and Washer (No. 46)
and pull out the
Pull Pin
(No. 60). Fold the
Sliding
Rail (No. 62)
to vertical
angle (Figure A).
SAFETY NOTE:the Seat
(No. 71) will
glide down
when folding the
Sliding
Rail (No. 62).
Reinsert Pull Pin (No. 60)
into the hole on the M
ain
Frame (No. 44)
, then
tighten Knob (No. 47)
and
Washer (No. 46)
to
Sliding Rail (No. 62)
.
(Figure B)
Figure B
Figure A

10
UNFOLDING GUIDE
When in use, you can put the
Sliding Rail (No. 62)
down.
Pull outPull Pin (No. 60) from the hole on the M
ain
Frame (No. 44), then remove Knob (No. 47)
and
Washer (No. 46) from Sliding Rail (No. 62). (
Figure
A)
Slightly lay down the Sliding Rail (No. 62), the
n
tighten Knob (No. 47) and Washer (No. 46) to M
ain
Frame (No. 44). and insert the Pull Pin (No. 60)
to
Main Frame (No. 44). (Figure B).
Figure A
Figure B

11
BATTERY INSTALLATION & REPLACEMENT
BATTERY INSTALLATION:
1.Take out 2 AAA batteries from meter box.
2.Press the buckle of battery cover on the back of the Computer (No. 13), then remove battery cover.
3.Install 2 AAA batteries into the battery case on the back of the Computer (No. 13). Pay attention to the
battery + and – poles before installing.
4.Press the buckle of battery cover, then put the battery cover back to the back of the Computer (No. 13).
The installation is complete!
BATTERY REPLACEMENT:
1.Press the buckle of battery cover on the back of the Computer (No. 13), then remove battery cover.
2.Remove the 2 old AAA batteries in the battery case and install 2 new AAA batteries into the battery case
on the back of the Computer (No. 13). Pay attention to the battery + and – poles before installing.
3.Press the buckle of battery cover, then put the battery cover back to the back of the Computer (No. 13).
The replacement is complete!
NOTE: Always change both batteries at the same time. Do not mix battery types and do not mix old and new
batteries. Dispose batteries according to your state and regional guidelines.

12
EXERCISE COMPUTER
■KEY FUNCTIONS：
Pressing the MODE key to select and lock on a function for following sequence:
SCANTIMECOUNTDISTCALTOTAL COUNT (TOT) SPMT/500M SCAN
Pressing and hold the MODE key with 3 seconds to reset the value to zero (without TOT).
■SLEEP MODE:
The system turns on when MODE key is pressed and system senses a signal input from the sensor.
All of the value will be reset to zero (without TOT)
The system turns off automatically when the sensor has no signal input or no key are pressed for approximately 4 minutes.
■FUNCTIONS:
SCAN: Display changes according to the next diagram every 6 seconds.
COUNT: The current count from starting exercise.
DIST: The current distance from starting exercise.
TIME: The total working times elapsed from starting exercise.
TOTAL COUNT (TOT): The total count from first inserting batteries
CALORIES: The calorie burned from starting exercise.
SPM: Number of strokes per minute, indicating the stroke speed during exercise.
T/500M: The time for 500 meters during exercise
■BATTERY INSTALLATION & REPLACEMENT
SPECIFICATION
SCAN
6S
TIME
99M:59S
COUNT
0~9999
DIST
0~9999 Meters
TOT
0~9999
CALORIES
0.0~999.9 Kcal
SPM
0~299
BATTYERY
SIZE-AAA *2
Operating temperature
0~40
℃
(32
℉
-104
℉
)
Storage temperature
-10~60
℃
(14
℉
-140
℉
)

13
APP CONNECTION:
1. Scan the QR code below to download the SunnyFit app onto your mobile device.
2. If this is your first time using the SunnyFit app, follow the in-app instructions to register for your
free SunnyFit account and log in.
3. Ensure that the Bluetooth function is turned on from your mobile device.
4. To connect the equipment to the SunnyFit app:
a. From the “Workout” tab, press on the “Search” button to search for your equipment.
b. Once your equipment appears on the list, tap the “Select” button to confirm.
c. Note: If your equipment does not appear on the "Searching for Equipment" list, check
the EXERCISE COMPUTER on your equipment to ensure that it is not in sleep mode
and your phone's Bluetooth function is on, then tap "Retry" to search again.
d. Once your equipment shows up on the “Workout” tab as “Currently Selected”, your
equipment is now ready to display, track, and record your equipment’s workout stats
on the app!
5. If you are unable to replicate these steps, or have any other issues with the SunnyFit app,
please contact SunnyFit support at [e-mail], or use the in-app “Contact Us” form
to request support (“Me” tab -> “Contact Us”).

14
EXPLODED DIAGRAM

15
PARTS LIST
No. Description Spec. Qty. No. Description Spec. Qty.
1 Front Stabilizer 1 44 Main Frame 1
2 Washer Φ8*Φ16*1.5 6 45 Sensor Wire 1
3
Bolt
M8*55
2
45A
Sensor Wire A
1
4L/R End Cap (Left / Right) 2 45B Sensor Wire B 1
5 Nut M8 5 46 Washer Φ24*Φ12*2 1
6 Screw ST4.2*25*Φ10.5 4 47 Knob M12 1
7 Handlebar 1 48 Bolt M12*160 4
8 Foam Grip Φ26*3*215 2 49L/R Pedal L/R 2
9 End Cap Φ28*15 2 50 Pedal Strap 2
10 Left Belt Cover 1 51 Magnet Φ15*7 1
11 Screw ST4.2*19*Φ8 11 52 Spring Washer Φ8 8
12 Screw ST4.2*16*Φ8 6 53 Wheel Φ40*92 3
13 Computer 1 54 Casing Pipe for Idler Wheel Φ13*Φ8*78 3
13A Computer Wire A 1 55 Bearing 608Z 6
13B Computer Wire B 1 56 Rubber Pad 1
14 Tension Control Knob 1 57 Right Belt Cover 1
15 Washer D5 1 58 Bolt Φ10*96 1
16 Screw M5 1 59 Screw M6*16 1
17 Nut M10*1*H8*S15 4 60 Pull Pin Φ8*100*105 1
18 Nut M10*1*H5*S17 4 61 Bolt M8*10 2
19 Cover for Mesh Belt Wheel Φ149*14 1 62 Sliding Rail 1
20 Outer PC Board 1 63 Screw M6*16 4
21 Volute Spring 1 64 Washer Φ6*Φ12*1 8
22 Axle for Mesh Belt Wheel 1 65 Limit Mat Φ33*Φ8*13 4
23 Bearing 6000-ZZ 4 66 Limit Axle Φ12*80 2
24 PC Board 1 67 Computer Support 1
25 Bolt M5*45*Φ4.8 1 68 End Cap J80*40*18 1
26 Mesh Belt Wheel Φ145 1 69 Rear Support 1
27 Belt Wheel Φ104 1 70 End Cap 2
28 Bolt M6*55*S10 3 71 Seat DDPU986 1
29 Circlip d10 3 72 Screw M8*20 4
30 Bolt M6*55*15*S10 1 73 Bolt M8*125*15*S14 3
31
Wave Washer
Φ13.5*Φ10.2*0.4
1
74
U Shape Bracket
2
32 Spacer Φ10*Φ6.1*40 1 75 Left Seat Supporting Board 1
33 Mesh Belt Pulley Φ45*35 1 76 Right Seat Supporting Board 1
34 Screw M8*20*S6 4 77 Spacer d8*Φ15*4 6
35 Washer d8*Φ20*1.5 10 78 Spanner S17,19 1
36 Handlebar Seat 1 79 Allen Wrench S5 1
37 Screw M5*10*Φ10 7 80 Allen Wrench S6 1
38 Mesh Belt t1.5*22*2270 1 81 Spanner S10,13,14,15 1
39 Belt 6PJ250 1 82 Screw M5*15 2
40 Inertial Wheel Φ176 1 83 Screw ST4.2*15 2
41 Adjusting Bolt 4 84 Tablet Fixing Plate 1
42 Adjusting U Seat 30*10*1.5 4 85 Tablet Holder 1
43 Nut M6*H6*S10 8 86 Bolt M8*60 2
Version 1.0

16