Sunrise Medical QUICKIE SALSA Manual

Directions for use
QUICKIE SALSA

Table of contents
1 Your Wheelchair 5
2 How to use this manual 6
2.1 Introduction .............................................................................. 6
2.2 Guarantee ................................................................................. 6
2.3 Warranty conditions.................................................................. 6
3 Label explanations / Word definitions 7
3.1 Definitions of words used in this manual................................. 7
3.2 Label explanations ............................................................. 7 + 8
4 General safety warning and user tips 9
4.1 General warnings .................................................................... 9
4.2 Features and options ............................................................... 9
4.3 Kerbs........................................................................................ 9
4.4 Routine service........................................................................ 9
4.5 Emergency freewheel.............................................................. 9
4.6 EMC - Radio transmitting devices. ........................................ 9
4.7 Emergency braking ................................................................. 9
4.8 Sharp turns .............................................................................. 9
4.9 Batteries................................................................................... 9
4.10 Tyres......................................................................................... 9
4.11 Weight limit ............................................................................. 9
4.12 Wheelchair motors ................................................................ 10
4.13 Hot surfaces ........................................................................... 10
4.14 Wheelchair range................................................................... 10
4.15 Road caution .......................................................................... 10
4.16 Adverse conditions ................................................................ 10
4.17 Ramps .................................................................................... 10
4.18 Transfer to and from the chair............................................... 10
4.19 Lift and tilt modules .............................................................. 10
4.20 Anti-tips................................................................................. 10
4.21 Use on a slope........................................................................ 10
4.22 Using a vehicle mounted passenger lift................................ 11
4.23 Creep mode............................................................................ 11
4.24 Stability of your wheelchair.................................................. 11
4.25 Wheels ................................................................................... 11
4.26 Rear view mirror ................................................................... 11
4.27 Crutch holder......................................................................... 11
4.28 Lights and indicators............................................................. 11
4.29 Swing away tray .................................................................... 11
4.30 Using a kerb climber ............................................................. 12
4.31 Lap belt .................................................................................. 13
4.32 VR2 Controller ..................................................................... 13
5 Preparing your wheelchair for use 14
5.1 Handling the wheelchair ......................................................... 14
5.2 Preparation for transportation or storage ............................... 14
5.3 Re-Assembling ....................................................................... 14
5.4 Emergency freewheel.............................................................. 14
5.5 Drive wheel suspension Salsa................................................. 14
5.6 Control joystick unit position.................................................. 14
5.7 Getting ready to drive ............................................................. 14
5.8 Armrests ............................................................................ 15- 17
5.9 Legrests............................................................................. 18 - 19
6 Seating 20
6.1 Firm seat board...................................................................... 20
6.2 Seat cushions......................................................................... 20
6.3 Removable seat covers .......................................................... 20
6.4 Standard backrest upholstery................................................ 20
6.5 JAY backrests........................................................................ 20
6.6 Seat Height Adjustment ........................................................ 20
6.7 Seat Width Adjustment ......................................................... 20
6.8 Seat Depth Adjustment ......................................................... 21
6.9 Backrest Angle Adjustment .................................................. 21
6.10 Back Height Adjustment ............................................... 21 - 23
6.11 Manual adjustable backrest (manual recline) ....................... 23
6.12 Manual setting of the seat angle on the SALSA................... 23
6.13 Headrest ................................................................................. 23
6.14 Powered Seating .................................................................... 24
7 The VR2 Hand Control series 25 - 27
7.1 VR2 ........................................................................................ 25
7.2 VR2-L .................................................................................... 26
7.3 VR2 Dual control unit........................................................... 26
8 Troubleshooting using the VR2 Hand Control 28
9 Controller Mounts 29
9.1 General warnings .................................................................. 29
9.2 Attendant control................................................................... 29
9.3 Parallel swing-away control.................................................. 29
10 Batteries and charging 30
10.1 Batteries ................................................................................. 30
10.2 Safety cut-outs....................................................................... 30
10.3 General battery information ................................................. 30
10.4 Maintenance free batteries.................................................... 30
10.5 Battery care ........................................................................... 30
10.6 Maintenance free battery care plan ...................................... 30
10.7 General charger information................................................. 30
10.8 Charger safety features ................................................. 30 - 31
10.9 Procedure for connecting the charger and charging ............ 31
10.10 Charger safety and caution notes .......................................... 31
10.11 The range of your vehicle ...................................................... 31
10.12 Common battery statements.................................................. 31
10.13 Battery warranty.................................................................... 31
11 Transportation 32
11.1 Transportation warnings: ...................................................... 32
11.2 Occupant restraint instructions............................................. 32
11.3 Crash testing on the SALSA ................................................. 33
11.4 The tie down label and placement......................................... 33
11.5 Securing the wheelchair into the vehicle.............................. 33
11.6 Salsa tie downs ...................................................................... 33
12 Maintenance and Cleaning 34
12.1 Tyre maintenance and pressures........................................... 34
12.2 Tyre wear ............................................................................... 34
12.3 Drive wheel tyre repair ......................................................... 34
12.4 Removing the castor wheel ................................................... 34
12.5 Cleaning your wheelchair ..................................................... 34
12.6 Inspection of the upholstery / seating .................................. 34
12.7 Cleaning seating .................................................................... 34
12.8 Cleaning controls .................................................................. 34
12.9 Lighting bulb exchange procedure ............................... 34 - 35
12.10 Electrical connections ........................................................... 35
12.11 How to connect the cables to the batteries............................ 35
12.12 Controller access ................................................................... 35
12.13 Storage ................................................................................... 35
12.14 Authorised Sunrise Medical service agents ......................... 35
12.15 Recommended maintenance routines........................... 35 - 36
12.16 Performance checks............................................................... 36
13 Specification sheets (EN 12184 & ISO 7176-15) 37
14 Service History 38
15 Disposal 38
16 SALSA Battery Wiring Diagram 39

4 Quickie SALSA 060474
ENGLISH

Quickie SALSA 5
060474
ENGLISH
Armrest
Legrest
Controller
Cushion
Castor
Footplate
Drive wheel
Skirt Guard
Anti-tips
Backrest
Batteries

6 Quickie SALSA 060474
ENGLISH
1 Your Wheelchair
We at Sunrise Medical want you to get the best out of your Salsa
wheelchair. This Owner’s Manual will familiarise you with the chair
and its features. It contains hints on everyday usage and general care
in addition to information on the high quality standards which we
adhere to and details about the guarantee.
Your wheelchair should be delivered fully assembled for your use;
there are a wide range of components and adjustments available on
the Salsa. For further information about these you should contact your
Sunrise Medical authorised dealer.
Your wheelchair will reach you in excellent condition having been
individually inspected before leaving our factory. Following the
guidelines for maintenance and cleaning your wheelchair will
maintain its first class condition and give you complete satisfaction.
The Salsa has been designed for use by an individual on a daily basis.
It is suitable for both indoor and outdoor use (Class B). It is only
intended for use as a pavement vehicle, but may also be used when
crossing between pavements.
This vehicle has been designed for a single occupant of limited
mobility up to the weight of 140Kg (dependent on options chosen
for your chair) who has the cognitive, physical and visual ability to
control the vehicle safely on a maximum slope of 16% (9°). If you
are in any doubt as to the suitability of the power chair, contact your
local Sunrise Medical approved supplier for clarification, prior to
commencing use.
It is very important to read the relevant section of the owner’s manual
when making any minor adjustments. Contact your local Sunrise
Medical authorised dealer for more complex adjustments.
If you have any queries about the use, maintenance or safety of your
wheelchair, please contact your local Sunrise Medical authorised
dealer. If you do not know of an authorised dealer in your area or have
any other questions please write or telephone:
Sunrise Medical LTD.
Sunrise Business Park
High Street, Wollaston
West Midlands DY8 4PS
England
Phone: [phone]
Fax: [phone]
Sunrise Medical is ISO 9001 certified, which ensures quality at all
stages of the development and production of this wheelchair.
This product is manufactured to comply with Medical Device
Directive 93/42/EEC.
How to use this manual2
2.1 Introduction
Please keep a note of your local authorised dealer address and
telephone number in the space below.
In the event of a breakdown, contact them and try to give all relevant
details so they can help you quickly.
The wheelchairs shown and described in this manual may not be
exactly the same in every detail as your own model. However, all
instructions are still entirely relevant, irrespective of detail differences.
The manufacturer reserves the right to alter without notice any
weights, measurements or other technical data shown in this manual.
All figures, measurements and capacities shown in this manual are
approximate and do not constitute specifications.
2.2 Guarantee
The guarantee form is included in the Sunrise Pack. Please fill in the
relevant details and return to us to register your entitlement.
THIS IN NO WAY AFFECTS YOUR STATUTORY RIGHTS.
2.3 Warranty conditions
1) The repair or replacement will be carried out by an authorised
Sunrise Medical dealer/service agent.
2) To apply the warranty conditions, should your wheelchair require
attention under these arrangements, notify the designated Sunrise
Medical service agent immediately giving full information about the
nature of the difficulty. Should you be operating the wheelchair away
from the locality of the designated Sunrise Medical service agent,
work under the “Warranty Conditions” will be carried out by any
other service agent designated by the manufacturer.
3) Should any part of the wheelchair require repair or replacement, as
a result of a specific manufacturing or material defect, within twenty
four months from the date on which the possession of the wheelchair
was transferred to the original purchaser, and subject to it remaining
within that ownership, the part or parts will be repaired or replaced
completely free of charge if returned to the authorised service agent.
4) Any repaired or replaced part will benefit from these arrangements
for the balance of the warranty period applicable to the wheelchair.
5) Parts replaced after the original warranty has expired are covered
for a further twelve months.
6) Items of a consumable nature will not generally be covered during
the normal warranty period, unless such items have clearly suffered
undue wear as a direct result of an original manufacturing defect.
These items include amongst others upholstery, tyres, inner tubes and
similar parts. On powered products this will also include batteries,
motor brushes etc
7) The above warranty conditions apply to all wheelchair parts for
models purchased at full retail price.
8) Under normal circumstances, no responsibility will be accepted
where the wheelchair has required repair or replacement as a direct
result of:
a) The wheelchair or part not having been maintained or serviced
in accordance with the manufacturer’s recommendations, as stated
in the Owner’s Manual and/or Service Manual. Or failing to use
only the specified original equipment parts.
b) The wheelchair or part having been damaged by neglect, accident
or improper use.
c) The wheelchair or part having been altered from the
manufacturer’s specifications, or repairs having been attempted
prior to the service agent being notified.
Dealer signature and stamp
*
(

Quickie SALSA 7
060474
ENGLISH
Label explanations / Word definitions3
3.1 Denitions of words used in this manual
Word Definition
Warning Advice to the user of a potential risk
of injury if the advice is not followed
Note General advice or best practice
3.2 Label explanations
Labels and their descriptions
Warning - Do Not Touch - HOT Lever position for the freewheel mechanism.
Down – IN DRIVE Up - IN FREEWHEEL
WARNING – Do Not Touch - Static may damage equipment
Attached to Joystick
WARNING – Do not drive your wheelchair on a slope with the
backrest reclined and/or the seat lifted
WARNING – Danger of finger entrapment WARNING – Maximum user weight for the chair is 140Kg
Indicates battery charge point
Location of 70Amp circuit breaker
140 Kg
MAX

8 Quickie SALSA 060474
ENGLISH
Labels and their descriptions
Battery Label – Warning Instructions and Circuit Diagram
Back Rest Recline Seat Lift
Seat Tilt in Space
Do not disengage free wheel whilst on a slope Ensure drive is engaged before starting off.
Left Leg Rest
Right Leg Rest
Both Leg Rests

Quickie SALSA 9
060474
ENGLISH
4 General safety warning and user tips
4.1 General warnings
• Always ensure that your wheelchair is switched off before
attempting to mount or dismount.
• Always ensure that you are able to operate all controls from a
comfortable position. Paying attention to your posture is essential
to ensure your continued comfort and well being.
• Alwaysmakesurethatyoucanbeseenclearly,especiallyifyou
intend using your wheelchair in poor light.
• Thiswheelchairhasbeenbuilttomatchtheneedsofaparticular
user. If used by another user then it may need to be adjusted and
reprogrammed.
• Donotletchildrenorothersuseyourwheelchair.
4.2 Features and options
Some of the options shown in this manual may not be available
in your country and may also restrict the overall physical limits
of the standard product (e.g. max. speed, user weight limit,
etc.). Those limitations are marked on the order form, in the technical
manual and in this owner’s manual. For further information please
consult your Sunrise Medical authorised dealer.
4.3 Kerbs
Never descend a kerb Forwards with a RWD chair. Please read
carefully the section 4.30. on kerb climbing in this manual
before attempting to mount and dismount any kerbs in your
wheelchair.
Do not attempt to climb or descend a series of steps. It is unsafe to do
so and could cause personal injury or damage the chair. The Salsa has
only been designed to climb a single step or kerb.
4.4 Routine service
The recommended service interval is one year. (See service
history table in section 14).
4.5 Emergency freewheel
Please remember that you have no braking facility when the
freewheel levers are moved from the normal drive position
to the freewheel position (Fig. 1 and Fig. 2). Always ensure
an attendant is with you when bringing the chair into the freewheel
mode.
The wheelchair must never be left with one or both levers in the
freewheel position. For an enhanced description of this facility and its
limitations to use please see later section at 5.4.
4.6 EMC - Radio transmitting devices.
When operating two-way radio, walkie-talkies, C.B., amateur
radio, public mobile radio and other powerful transmitting devices the
wheelchair should be brought to a halt and turned off.
The operation of cordless, mobile telephones and cell phones including
hands-free devices is permitted but if abnormal operation of the
wheelchair is encountered then the chair must be brought immediately
to a halt and turned off.
Note: the electrical systems of the wheelchair may disturb the
performance of alarm systems in retail shops.
4.7 Emergency braking
There are three ways to stop your wheelchair:
1. Simplest and safest way to stop the wheelchair is to release the
joystick (see Hand Control section 7). This will bring the chair
to a halt in a controlled manner.
2. Pulling back the joystick will brake the chair abruptly with a fast stop
3. Switching the control system off whilst the chair is in motion will
also bring the chair to a halt. This third method is only to be used in an
emergency situation as the stopping action is very abrupt.
4.8 Sharp turns
Full speed turns should not be attempted. If you need to turn
sharply you must reduce your speed with the joystick or speed
setting. This is particularly important when travelling across or
down a slope. Disregarding this advice could lead to your wheelchair
tipping over.
4.9 Batteries
Your wheelchair is supplied as standard from Sunrise Medical
with maintenance-free batteries. These only require regular
charging. Before charging, please read section 10 in this
manual.
Do not, under any circumstances, tamper with the batteries. If in any
doubt contact your local Sunrise Medical authorised dealer.
Note: Before using your vehicle for the very first time, please charge
your batteries for a period of 24 hours.
Avoid contact with acid on damaged sealed type batteries or wet
batteries. Battery acid can cause burns to the skin as well as damage to
floors, furniture and your wheelchair. If it comes into contact with the
skin or clothing, wash immediately with soap and water. If it comes
into contact with the eye, immediately flood the eye with running cold
water for at least 10 minutes and seek medical attention immediately.
Acid can be neutralised with baking soda and water. Take care to
keep batteries upright at all times, especially when transporting your
wheelchair.
Battery and charger type:
24V (2x12V) / 60 Ah/20h. Maintenance free
Dimensions: 197 x 165 x 197 mm.
Connector: 3 pins “Neutrik” type
4.10 Tyres
Your wheelchair tyres can wear depending on use. Check them
regularly in accordance with the service instructions in this
manual, especially the pressure of the tyres.
NEVER inflate the tyres using a garage forecourt airline, always use
the pump provided.
4.11 Weight limit
• The user plus items carried should never exceed a total
weight of 140Kg
• Neverusethischairforweighttrainingifthetotalweight(user
plus additional weights) exceeds a total weight of 140Kg
• Exceedingtheweightlimitislikelytodamagetheseat,frameor
fasteners and may cause severe injury to you or others from chair
failure
• Exceedingtheweightlimitwillvoidthewarranty.
Fig. 1 Fig. 2

10 Quickie SALSA 060474
ENGLISH
Note: Ensure controller is switched off during transfers to avoid
unintentional movement.
4.19 Lift and tilt modules
Please be aware that the lift and tilt modules present a trap
hazard. Make sure that when operating the tilt and lift it is free
from all clothing, hands, feet and other extremities to prevent
injur y.
Do not drive on ramps or slopes with the seat tilted, reclined or raised.
Before attempting to climb or descend a slope, return to an upright
position
4.20 Anti-tips
Make sure that anti-tips are not damaged or worn before using
your chair.
Attendants must be aware of the location of the anti-tips to
prevent feet being trapped underneath causing injury
Attendants - Do not stand on the anti-tips, this could cause the
wheelchair to become unstable.
4.21 Use on a slope
Your wheelchair has been designed and tested to allow its use
on slopes or gradients of up to 9° (16%). However, you have the
option of adjusting your seating position with either a lift, tilt or
recline or a combination of these options, then in certain circumstances
your wheelchair could become unstable. Before attempting to climb or
descend a slope or a kerb, caution should be taken when using weight
shift options (e.g. powered tilt or recline) of the seat and/or your
body for a counter balance weight. To improve stability lean forward
when driving uphill, with the seat and back in an upright position.
Alternatively sit in an upright position when travelling in a forward,
downhill direction or tilt and/or recline the seat backwards.
We strongly recommend that you return the seat and back to an
upright lowered position before attempting to climb or descend
a slope. Failure to do this may cause the wheelchair to become
unstable.
If you are in any doubt about the capabilities of your wheelchair on
a slope then do not attempt to drive up or down the slope/kerb; try to
find an alternative route.
4.21.1 Gradients: ascents
When going uphill, keep the chair moving. Steer by moving
the joystick from side to side. If you have stopped on a hill, you
should start slowly. If necessary lean forward to prevent the
tendency for the front wheels to lift.
4.21.2 Gradients: descents
On descents, it is important not to let the wheelchair accelerate
beyond its normal level of ground speed. In fact, it is safer to
proceed slowly down steep descents (below the speed of 5kph)
and stop, if any anxiety arises regarding directional control. If the
chair picks up speed, centre the control to slow it or to stop all forward
movement, then restart slowly and do not allow the speed to increase.
The solid state controller has the benefit of a logic system that will
help compensate when driving along a camber or up a hill. This is an
added safety feature on your wheelchair. In addition of course, you
may control the wheelchair speed by using the speed control.
4.12 Wheelchair motors
After prolonged use, the motors will produce heat, which is
radiated through the motors’ outer casing. Do not touch the
motors’ outer casing for at least 30 minutes after using the
wheelchair, to allow it to cool. (Fig. 3)
4.13 Hot surfaces
Not only the motors can get hot during the operation of the chair,
but also the upholstery material and armrests when standing in
the sun.
4.14 Wheelchair range
The range of your wheelchair can be affected by many factors
such as user weight, terrain, ambient temperature, use of
powered options and battery condition. The stated range in the
sales literature should be seen as the theoretical maximum (ISO 7176;
Part 4) and may not be attained by every user (also see section 11.12.
in this manual).
We recommend that every user initially limit their journey to half
the stated range, until they have confidence in the actual range their
wheelchair can attain. If your battery indicator is showing a low
charge then do not attempt a long journey unless you are confident in
reaching your destination and also returning to your home without the
risk of being left stranded.
4.15 Road caution
Please show the utmost consideration for the other traffic on
the road. Remember that the last thing a car or lorry driver
expects to see is a wheelchair backing off the kerb into the
road. If in any doubt, do not risk crossing the road until you are certain
that it is safe. Always cross the road as quickly as possible; there may
be other traffic.
4.16 Adverse conditions
Please be aware that when driving your wheelchair in adverse
conditions, e.g. on wet grass, mud, ice, snow or other slippery
surfaces, you may experience a reduction in the grip and
traction of your wheelchair. We recommend you take extra precautions
in these conditions, particularly on hills and slopes; your wheelchair
could become unstable or skid causing possible injury. Extreme
variances in temperature may trigger the self protect mechanism in
the control system. If this occurs the control system will temporarily
shut down to prevent damage to the electronics or the chair.
4.17 Ramps
When using a ramp, please ensure that it is capable of taking
the combined weight of the power chair and yourself. If a ramp
is being used to load a chair into a vehicle, please ensure the
ramp is properly secured to the vehicle. Always approach the ramp
head-on and exercise caution.
Note: Please ensure your ramp is suitable for the product you are
transporting.
4.18 Transfer to and from the chair
Sunrise Medical recommend that you consult your healthcare
professional for assistance in developing your personal front or
side transfer technique to best suit your needs and avoid any
personal injury.
Fig. 3

Quickie SALSA 11
060474
ENGLISH
4.22 Using a vehicle mounted passenger lift
Wheelchair lifts are used in vans, buses and buildings to help
you move from one level to another. Ensure that the user and
all carers fully understand the lift manufacturer’s instructions
for using the passenger lift.
Never exceed the lift manufacturer’s recommended safe working load
and load distribution guidance.
Always turn off all power when you are on the lift. If you fail to do so,
you may touch the joystick by accident and cause your chair to drive
off the platform. Be aware that a rollstop at the end of the platform
may not prevent this.
Always position the user securely in the chair to help avoid falls while
on the lift.
Always ensure the chair is in drive mode when using passenger lift
(wheels locked not in freewheel mode).
4.23 Creep mode
Please ensure your backrest recline angle relative to floor
level, which is a combination of the back recline itself and
the tilt angle, does not exceed 12° to drive the chair safely.
If your backrest to level floor angle exceeds this limit the chair will
automatically convert into “creep mode” which will allow you a
maximum of 10% of the speed programmed in the profile.
WARNING - If you have a manual recline backrest on your
wheelchair, please be aware that there will be no feedback system to
the controller that tells it that the seat is in a reclined position. If you
recline your backrest and attempt to drive, it will not go into ‘creep
mode’, it will instead drive at full speed. This is especially dangerous
when attempting to drive up a slope.
4.24 Stability of your wheelchair
Please follow the user instructions in this manual regarding the
use of seat lift and tilt modules and the use of your chair on a
slope, other variables can affect your chair stability, including:
- Movement of the user
- Effects of the addition of accessories or other equipment
- Inappropriate adjustments or modifications to the wheelchair
In some cases these issues are further compounded by the effects of
the local environment such as:
- Hills
- Slopes
- Ramps
- Sloping pavements
- Dropped kerbs
Furthermore different body proportions of a wheelchair user affect
stability for example:
- Lower limb wasting or amputation
- Increased upper torso mass
- Upper torso height
- Obesity
4.25 Wheels
Always use the pump that is supplied with the chair,
Never use a forecourt pump.
Inspect all tyres regularly for signs of wear.
Do not drive over anything that could cause punctures in the tyres.
Ensure that there are no objects in your path that could possibly
become lodged in your chair mechanism or in the spokes of the rear
wheels. This could cause the chair to come to a sudden stop.
Riding over drains or grids could cause the wheelchair castors or
wheels to become lodged, causing the chair to come to a sudden stop.
Always maintain the correct pressure for the tyre. These are listed in
section 12 of this manual.
Pneumatic Tyres with OKO uid.
The OKO fluid is only meant as a temporary repair to the tyre. It must
be replaced or repaired as soon as possible.
The OKO fluid is classified as non hazardous but may cause irritation
to the skin with prolonged contact.
4.26 Rear view mirror
To avoid injury to people around you please be aware that the
mirror protudes outside the space envelope of the chair and
could cause injury to someone when driving past.
The mirror must be used on the 10KPH model on UK roads.
Always make sure that when using the mirror that it is clean and
unbroken so that it does not impair your visibility.
4.27 Crutch holder
Make sure that the crutch is securely fastened to the crutch
holder.
Make sure that the crutch is not interfering with the mechanisms of the
chair.
Make sure that the crutch does not protrude from the chair.
Do not attempt to remove the crutch whilst the chair is in motion.
Always come to a complete stop and turn off the power to the controls
before attempting to remove the crutch. This will avoid accidentally
operating the chair.
4.28 Lights and indicators
Ensure that the lights and indicators are functioning correctly
and lens are clean before going outdoors at night.
Lights assembly can become very hot - Care must be taken if
removing them for repair.
4.29 Swing away tray
The maximum weight allowed for the tray is 2.5kg.
Do not overload the tray, this could cause the tray to break or
could cause the chair to become unstable.
Do not leave lit cigarettes or other heat sources on the tray as this
could cause the tray to deform and mark.
Ensure that all extremities and clothing are free when positioning the
tray for use.
First Aid measures for OKO fluid
Skin - Wash skin with plenty of water
Eyes - Immediately flood the eye with plenty of water for at least
5 minutes holding the eye open.
Ingestion - Drink lots of water - Seek medical attention
immediately.

12 Quickie SALSA 060474
ENGLISH
4.30 Using a kerb climber
4.30.1 Mounting a kerb or step (Fig 6)
Always approach a kerb at 90° (Fig 4 & Fig 5)
• Approachthekerb(step) head
on driving forwards slowly and
steadily and always at a 90°
angle.
• As the kerb climber or castor
makes contact with the kerb
(step), the wheelchair should
be moving slowly. Small kerbs
can be climbed from a standstill.
• Applysufficientpowertothemotorstoliftthefrontofthechair
up onto the kerb (step) and then apply slightly more power and
speed so that the drive wheels climb the kerb (step) smoothly and
without hesitation. As far as possible, keep the joystick in the
straight forward position.
• In accordance to the ground clearance, the maximum obstacle
height possible to climb is 5 cm (10 cm with kerb climber)
WARNING : The approach speed and process can vary depending on
your wheelchair performance and castor wheel choice.
4.30.2 Dismounting the kerb (Fig. 9)
• Reversethechairslowlyandcarefullyuntilbothrearwheelsare
on the edge of the kerb, again in a 90° position to the kerb.
• Reverseasslowlyaspossibleoffthekerbwiththerearwheels.
You will feel more secure if you can lean forward, but if you
can’t, don’t worry, the wheelchair is extremely stable. As long as
you stay within its limitation, you will be quite safe.
• Thefrontofthechairwillnaturallyfollowdownthekerbasyou
continue to drive slowly backwards.
4.30.3 Kerb climber tting and removal procedure
(RWD base only)
• Locatethekerbclimberbarinto
the left hand location bracket
and push it into the right hand
receiver bracket (Fig. 7 & Fig
8).
• Hold the kerb climber with
your left hand in the receiver
bracket.
• Aligntheholesofthereceiver
bracket and the kerb climber
tube and plug in the locking
pin from the top.
• Reverse the procedure to
remove the kerb climber.
Warnings
1. Please show the utmost consideration for the other traffic on the
road. Remember that the last thing a car or lorry driver expects to see
is a wheelchair backing off the kerb into the road. If in any doubt, do
not risk crossing the road until you are certain that it is safe.
2. Always cross the road as quickly as possible; there may be other
traffic.
3. Do not attempt to go up or down more than a 10 cm (4”) high kerb
(Salsa only with kerb climber fitted).
4. Do not attempt to use the kerb climber on a series of steps.
5. Do not attempt kerbs if on steep slopes or cambers.
6. Do not attempt any kerbs in the vicinity of drain covers, uneven or
gritty road surfaces.
7. Do not attempt to dismount a kerb any higher than 5 cm (2”) in the
forwards direction.
8. Do not mount or dismount kerbs at an angle other than straight on
(90 degrees) to the edge of the kerb.
9. Prior to climbing ensure your legrests will clear the kerb.
10. Take care of the anti-tips which might interfere with the kerb or the
ground when mounting or dismounting a kerb.
WARNING - This wheelchair is designed to be repaired and
assembled by a Sunrise Medical authorised dealer and not the
end user. The end user has to disassemble and assemble the chair
only for transportation (see section 5.2).
Fig. 4 Fig. 5
Fig. 8
Fig. 7
Fig. 6 Fig. 9

Quickie SALSA 13
060474
ENGLISH
4.31 Lap belt
The lap belt kit. (Fig. 10).
Fastening the lap strap.
Insert the 3 prong male buckle into
the female buckle until a click is
heard (Fig. 11)
To fit the lap strap.
Place the strap loosely across the
seat with the buckle closed.. (Fig.
12)
Pass the other ends of the strap
through the gap between the
backrest posts and the backrest
upholstery as shown. (Fig. 13)
Ensure that the adjusters & buckles
can be accessed & the strap is not
twisted. Fit the eyelet over the
rearmost bolt. Fit the plain washer,
sprung washer & nut. Tighten with
a 13.0mm spanner. Repeat for the
other side. (Fig 14)
Ensure that the lap strap is tight
enough to provide comfortable
support. A simple measure is to
keep a hands thickness between the
body and lap strap. For safety, check
the tension on the lap strap at least
once day. (Fig 15)
Generally, the lap belt should be
fixed so that the straps sit at an angle
of approximately 45° (Fig. 16), and when
correctly adjusted should not allow the user
to slip down in the seat.
Warning - Always make sure that the lap
strap is correctly secured and adjusted prior
to use.
A loose strap could cause the user to slip
down and cause serious injury.
Check lap strap and securing components at regular intervals for any
signs of fray or damage. Replace if necessary
When servicing, check for correct operation of the release buckle and
for any signs of wear on the material or plastic brackets
4.32 VR2 Controller (Fig. 17)
Avoid knocking your control system and especially the joystick. Be
careful not to strike obstacles with the control system or joystick when
you drive. Never drop the control system.
When transporting your wheelchair, make sure that the control system
is well protected. Avoid damage to cables.
To improve the reliability of the control system keep exposure to
extreme conditions to a minimum.
Do not expose your control system or its components to damp for
prolonged periods. If your control system becomes contaminated with
food or drink clean it off as soon as possible.
Controller precautions for use
In the event of the wheelchair moving in an unexpected way RELEASE
THE JOYSTICK. This action will stop the wheelchair under any
circumstances
Do not operate the control system if the wheelchair behaves erratically
or shows abnormal signs of heating, sparks or smoke. Turn the control
system off at once and consult your Sunrise Medical Authorised
Dealer.
Fig. 10
Fig. 11
Fig. 12
Fig. 13
Fig. 16
Battery Level Indicator
On/Off Button
Horn
Speed Indicator
Speed Buttons
Joystick
Fig. 14
Fig. 15
Fig. 17

14 Quickie SALSA 060474
ENGLISH
5 Preparing your wheelchair for use
5.1 Handling the wheelchair
Note: To dismantle the chair for transport or storage no tools are
required.
List of components when dismantled (components below are related to
the maximum detachable parts and dependent on the type of seating
system chosen):
1 pair of armrests
1 pair of legrests,
1 backrest (Std. Rehab/comfort seat only)
1 drive unit with seat frame
5.2 Preparation for transportation or storage
First remove the legrests
if swing away legrests are
attached. Leave the armrests in
the fold down position. (Fig.18)
disconnect the Hand Control,
(Fig. 19), if necessary. Release
and lift off the backrest at the
frame. Now you can store the
chassis part. By releasing the
freewheel mechanism on the
left and right side of the chassis
you can move the drive unit as
close as possible to the place you
want to store it.
You can also drive the base with
the joystick up or down a ramp into
and out of a car for transportation.
Make sure, when the chair is stored
or left in the car or anywhere else,
the controller is switched off and
the freewheel mechanisms
are engaged.
If there is a need to lift the drive unit the big side frame tubes should
be used. Caution should be taken if the chair is in freewheel.
To remove the control pod.
To remove the control pod you have to access the motor controller through
the plastic cover between the castor wheels and remove the square remote
control connector.
Place the control pod & arm in a safe place until required.
To reconnect the hand control just use the process in reverse.
5.3 Re-Assembling
Replace the backrest into the receivers and tighten the lever screws
carefully. If required reconnect the remote controller. Attach the
hangers. Make sure your freewheel mechanisms are engaged. Now
you are ready to drive the chair.
WARNING - Never lift the wheelchair by the armrests or the leg rests,
since they are detachable and harm could be done to the user or to the
wheelchair.
5.4 Emergency freewheel
By pulling the release levers on both
sides of the base into the up position
(Fig. 20+21) the brakes are released
from the motors.
This may only be used in an
emergency, or if you need to
manually push your wheelchair. It is
not intended for permanent use or to
push the wheelchair up/down a slope
with the user sitting in it.
Note: The chair’s automatic braking
system will not work unless the brake
release levers are in the “drive” or
down position.
WARNING - Motor surfaces can be hot after use. Be careful not to
touch the motor casing when disengaging the freewheel.
WARNING - Never attempt to disengage the freewheel mechanism
whilst sitting on a slope.
5.5 Drive wheel suspension Salsa
The SALSA has an effective and
adjustable drive wheel suspension
system as a standard feature. To
match your requirements on drive
comfort, the tension of the springs
at the damper can be adjusted.
Turning the aluminium ring on the
bottom of the spring downwards
will soften your ride, adjusting
the aluminium ring in a higher
position will harden it. This option
is to be used to match the different
user weights to the suspension
system. (Fig. 22). We recommend the suspension adjustments are
done equally on the left and right side of the chair.
5.6 Control joystick unit position
Make sure that the control system is mounted securely and that the
joystick position is correct. The hand or limb you use to operate the
joystick should be supported for example by the arm pad.
Do not use the joystick as the sole support for your hand or limb -
wheelchair movements and bumps could upset your control.
The remote is mounted on a sliding mechanism which enables
the control to be moved forwards and backwards. When the most
comfortable position has been selected, secure the slider by tightening
the locking screw. Ensure the locking screw is fully tightened prior to
use and especially when transporting your wheelchair.
5.7 Getting ready to drive
• Operate the on/off switch. The battery gauge will blink then
remain on after a second
• Checkthatthemaximumspeedissettoalevelwhichsuitsyou.
• Pushthejoysticktocontrolthespeedanddirectionofthewheel-
chair
Fig. 20
Fig. 21
Fig. 18
Fig. 19
Fig. 22

Quickie SALSA 15
060474
ENGLISH
5.8 Armrests
5.8.1 Armrests-removing and replacing (Fig. 23)
The armrests on both sides of the
wheelchair can be flipped up to allow side
transfer.
For side transfer flip the armrest all the
way up until it goes into its mechanical
stop. This frees your space for side
transfer.
To bring the armrests back into their position flip it all the way down
until it sits on its mechanical stop. Guide it in its downward movement
and do not let it fall on its own.
5.8.2 Armrest Height Adjustment (Fig. 24 - 39)
The following section outlines armrest height adjustment. In the case
of either fine or gross adjustment, it is a two-part process:
PART I: Adjust the armrest height through rotation
(Numbers 1-8 in the following pages).
PART II: Adjust armpad angle.
(Numbers 9-13 in the following pages).
PART 1: ARMREST HEIGHT ADJUSTMENT
1. Basic fine adjustment (up to one inch) of the armrest height can
be achieved using the 5mm fine height adjustment screw (B). To fine
tune the armrest’s height:
• Firstloosenthe6mmrotationboltsonbotharmrests(A).
• Turn the adjustment screws (B) counter-clockwise to raise the
armrest or clockwise to lower.
• Retightenbothrotationbolts(A).
(Use 20 N/m or 177 in/lb of torque.)
Refer to armpad realignment if desired armrest height is achieved.
NOTE– The fine-tune adjustment screws provide up to one inch
of armrest height adjustment. For more than one inch of height
adjustment, continue to Number 2. Each armrest can also be
adjusted independently for individuals who require an asymmetrical
configuration.
NOTE– The factory preset is 10” from the seat pan to the top of the
armpads.
2. To achieve more than one inch of adjustment, remove the 6mm
armrest rotation bolts on both sides of the ASAP seat.
3. Remove both armrest assemblies.
4. Remove both sets of 4mm armrest adjustment ring bolts.
5. Rotate the armrest height adjustment rings to match the desired
height designated in the Configuration Chart.
Fig. 23
Fig. 24
Fig. 25
Fig. 26
Fig. 27
Fig. 28
Fig. 29
Fig. 30

16 Quickie SALSA 060474
ENGLISH
6. Replace both sets of armrest adjustment ring bolts according to
the configuration chart.
(Use 10 N/m or 88.5in/lb of torque.)
7. Replace both armrest assemblies.
8. Replace the armrest pivot bolts on both sides of the seat.
Do not tighten completely.
PART II: ARMPAD ANGLE ADJUSTMENT
9. Loosen the 4mm armpad angle pivot bolts (A) on both armrests.
Remove the 4mm angle index bolts (B) on both armrests.
10. Use the 5mm fine height adjustment screw (C) to finish fine
tuning the height. Turn counter-clockwise to increase height or
clockwise to lower.
11. Tilt both armpads down (or up in the case of a lowered armrest)
until the armpads are in the preferred angle. Check to see if the height
is correct. (Refer to Number 10 for further height adjustment.)
12. Retighten both armrest pivot bolts. (Use 20 N/m or 177 in/lb of
torque.)
Fig. 31
Fig. 32
Fig. 33
Fig. 34
Fig. 35
Fig. 36
Fig. 37
Fig. 38

Quickie SALSA 17
060474
ENGLISH
13. Retighten both armpad angle pivot bolts (A). Replace both armpad
angle index bolts (B). (Use 10 N/m or 88.5 in/lb of torque for both sets
of bolts.)
5.8.3 Armpad Position Adjustment (Fig. 40 - 44)
1. Fine armpad position adjustments (one to two inches) are possible
by loosening the 4mm armpad adjustment bolts (E) and sliding the
armpad forward or backward as required.
Access to the rear adjustment bolt may require pivoting the armpad.
NOTE– If more than one to two inches of adjustment is required, refer
to chart below and continue to Number 3.
2. Retighten both adjustment bolts (E).
(Use 10 N/m or 88.5 in/lb of torque.)
3. For larger adjustments, remove both sets of armpad adjustment
bolts.
4. Slide both armpads to the next set of attachment holes (refer to
the chart). Retighten both sets of armpad adjustment bolts. (Use 10
N/m or 88.5 in/lb of torque.)
Fig. 39
Fig. 40
Fig. 41
Fig. 42
Fig. 43
Fig. 44

18 Quickie SALSA 060474
ENGLISH
5.9 Legrests
WARNING - Be aware of your environment to make sure you do not
injure your legs when legrests are extended.
WARNING - Always ensure that the legrests or footplates do not come
into contact with the castors before driving the wheelchair.
WARNING - Legrests are not to be used for lifting or carrying the
wheelchair with an occupant.
5.9.1 Fitting legrest
Offer the legrest assembly at right angles to the frame (Fig. 45), locate
the stem into the legrest and swing the assembly forward to lock in
position. To swing away the footrest, depress the retaining catch and
turn the footrest out. This can now be lifted out if required, (Fig. 46).
5.9.2 Footplates
The footplates may be flipped up to aid entry and exit from the chair.
WARNING - Do not use the footplates to stand on as the full weight
of your body may cause the chair to tip forwards. This could result in
injury and could damage the footrests.
5.9.3 Adjusting the footrest length
To adjust the footrest length remove the screw assembly on the footrest
stem as shown in (Fig. 47), adjust the length to suit. Ensure the bolts
are firmly located and tightened prior to use.
Note: The internal footrest stem may require cutting down in length to
allow the footplate position to be raised.
5.9.4 Hanger depth adjustment (Fig. 48 - 50)
1. Remove both sets of 5mm hanger depth adjustment bolts.
2. Slide both hanger receivers to the desired location. See bolt
pattern seat depth position settings (B)
3. Replace both sets of depth adjustment bolts. (Use 20 N/m or 177
in/lb of torque.)
Fig. 45 Fig. 46
Screws
Fig. 47
Fig. 48
Fig. 49
Fig. 50

Quickie SALSA 19
060474
ENGLISH
5.9.5 Manual Articulating / Elevating Legrest (ALR/
ELR)
To elevate:
Pull the legrest upwards and stop at the desired height. The legrest
will automatically lock in the chosen position.
To lower:
Push the release lever slowly forward. The legrest will lower the
angle. As soon as you release the lever, the legrest will be locked in
the current position.
WARNING - Keep hands clear of the adjustment mechanism between
the frame and the movable parts of the legrest while elevating or
lowering the legrest.
5.9.6 Powered Elevating or Articulating Legrest (Fig.
51)
Note: Both legrests can be operated simultaneously.
VR2 Control:
The actuator buttons can operate any factory approved actuator.
Operation is dependent on what options are fitted to your wheelchair.
To operate the legrests, seat tilt, seat lift or back rest recline.
• Pushone ofthe actuatorbuttons thathas theseat icononitto
select actuator mode
• Operatethejoystickleftor righttoselecttheactuatorrequired
(actuator 1 or actuator 2). Selection is indicated via the lighting of
the red LED adjacent to the desired actuator button.
• Operatethejoystickintheforwardorrearwarddirectiontomove
the leg rest/seat lift/tilt or recline up or down.
• Releasethejoystickwhenthedesiredangleisreached.
• Toreturntodrivemodepresstheactuatorbuttonagain.(Fig52)
Once the legrest is fully lifted or in its lowest position do not hold the
joystick in its operating position as this could damage the actuator.
Quickie Direct Actuator Control Box:
The direct actuator switches can operate any factory approved actuator.
Operation is dependent on what options are fitted to your wheelchair.
To operate the legrest, seat tilt, seat lift or backrest recline;
• Pushthetoggleswitchfortherelevantactuatorforwarduntilyou
reach the required angle/height.
• Releasethetoggleswitchandtheactuatorwillstop.
When the actuator reaches its maximum/minimum position do not
hold the toggle switch in its operating position as this could damage
the actuator. (Fig. 53)
Fig. 52
Fig. 53
Fig. 51

20 Quickie SALSA 060474
ENGLISH
Fig. 5.16
6 Seating
6.1 Firm seat board
The firm seat board is designed to allow pressure relief cushions such
as Jay to be used.
6.2 Seat cushions
Seat cushions supplied by Sunrise Medical will have Velcro® strips
that correspond to patches on the seat. You must ensure these are
aligned prior to using the wheelchair. Other cushions used should also
have Velcro® strips in a similar position to ensure the cushion does
not slip off the seat. The seat cushions, supplied by Sunrise Medical
all have removable covers.
6.3 Removable seat covers
The seat covers are all fully removable using zips or Velcro®. Once
brackets are removed seat covers can be removed. The zip for the
backrest is located on the underside of the cushion.
6.4 Standard backrest upholstery
Salsa is supplied with optima backrest upholstery, which can be
adjusted in tension to the individual’s requirements.
6.5 JAY backrests
The standard backrest assembly will allow the fitting of a JAY
backrest, which is available as an optional extra.
6.6 Seat height adjustment
To change the seat height loosen
the two bolts and remove the front
posts of the seat module Interface
(Fig. 54 & 55) on the bottom frame
with a 5mm allen key. The bolts can
be accessed through taking off the
front control module cover.
Take the safety clips off the flat rear
pins and pull the bolts out. Loosen
the two clamping bolts at the rear
flat posts.
Make sure the top frame does not
trap your fingers. Hold the top
frame securely in the up position.
Adjust the seat height by choosing
your required hole position of the
Module Interface and replace the bolts and the pins. Tighten them
securely and make sure that the safety clips are refitted
6.7 Seat width adjustment (Fig. 56 - 59)
1. Remove the 5mm width adjustment bolts (A) and the 4mm towel
bar adjustment bolt (B) .
2. Move the left side seat rail, armrest and backrest assembly to the
desired position. See seat width position settings (C)
3. Move the right side seat rail , armrest and backrest assembly to
the desired position. Replicate position settings used for the left side
4. Replace the width adjustment bolts (A) and the towel bar
adjustment bolt (B). (Use 10 N/m or 88.5 in/lb of torque for A and B.)
Fig. 54
Fig. 55
Fig. 56
Fig. 57
Fig. 58
Fig. 59