Sunrise Medical Quickie Q100 R Configuration guide

000691020.UK
Powered Wheelchair
General Manual
Q100R Configured
Q200R Configured

2Q100R-Q200R Configured Rev. A
03
UK
Wheelchair Components
We at SUNRISE MEDICAL have been awarded the ISO 13485 certificate, which affirms the quality of our products at every stage,
from R & D to production. This products meet the requirements in accordance with EC guidelines. Options or accessories shown are
available at extra cost.
EN
Dealer signature and stamp

ENGLISH
Q100R-Q200R Configured Rev. A 3
WARNING!
DO NOT USE YOUR WHEELCHAIR UNTIL THIS
MANUAL HAS BEEN READ AND UNDERSTOOD.
User Information
Intended use power wheel chairs:
Power wheelchairs are exclusively for a user who is unable to
walk or has limited mobility, for their own personal use in- and
outdoor.
When an Attendant Control Module is fitted, the Power
Wheelchair may be operated by an assistant on behalf of the
user.
When a Dual Control Module is fitted the Power Wheelchair
may be operated by the user, or control may be switched to an
assistant to operate on behalf of the user.
The maximum weight limit (includes both the user and any
weight of accessories fitted to the wheelchair) is marked on
the serial number label, which is affixed to the chassis of the
chair.
In the chair packaging there is an additional chair serial
number this can be affixed to the front page of the owners
manual supplied with the wheelchair.
Warranty can only be taken on if the product is used under the
specified conditions and for the intended purposes.
The intended lifetime of the wheelchair is 5 years. Please DO
NOT use or fit any 3rd party components to the wheelchair
unless they are officially approved by Sunrise Medical.
Area of application
The variety of fitting variants as well as the modular design
mean that it can be used by those who cannot walk or have
limited mobility e.g. because of:
• Paralysis
• Loss of extremity (leg amputation)
• Extremity defect deformity
• Joint contractures/joint injuries
• Strokes and brain injuries
• Neurological disabilities (e.g. MS, Parkinson…)
• Illnesses such as heart and circulation deficiencies,
disturbance of equilibrium or cachexia as well as for elderly
people who still have the strength in the upper body.
• Persons who are mentally and physically able to control an
input device to operate the chair and its functions in a safe
way.
When considering provision, please also note the body size,
weight including the distribution of body weight, the user’s
physical and psychological constitution, the age of the user,
their living conditions and their environment.
If in doubt a health care professional should be involved to
ensure the user is not exposed to unacceptable risks.
Sunrise Medical is ISO 13485 certified, which ensures quality
at all stages of the development and production of this
wheelchair.
Sunrise Medical declares under its sole responsibility that this
product is in conformity with the requirements of the directive
93/42/EEC amended by 2007/47/EEC.”
Sunrise Medical declares that this product fulls the
performance requirements for a “Crash Test” to
ISO 7176-19:2008.
The Serial Number and other important informaon may be
found on a label situated on the right-hand side, main frame
of the product.
If you are visually impaired, this
document can be viewed in
PDF format at
www.SunriseMedical.co.uk
or alternavely is available on
request in large text.

ENGLISH
4Q100R-Q200R Configured Rev. A
BACK UPHOLSTERY
Q100R/Q200R Features
CONTROL LEVER
HEIGHT/WIDTH
ADJUSTABLE
ARMRESTS
STABILISING BAR
BATTERY BOX
DRIVE WHEEL
MOTORS
FOOTRESTS
CUSHION
HAND CONTROL
MODULE
JOYSTICK
Due to its modular design, simplicity and wide range of adjustments, the Quickie Q100R/Q200R is a
perfect choice for easy service, refurbishment and recycle requirements.
As a part of our ongoing product improvement iniave, Sunrise Medical reserves the right to change
specicaons and design without noce. Further, not all features and opons oered are compable
with all conguraons of the wheelchair.
All dimensions are approximate and may be subject to change..
CASTORS

ENGLISH
Q100R-Q200R Configured Rev. A 5
  
  
2.1 Introduction: .......................................................................... 6
2.2 Guarantee .............................................................................. 7
  
3.1 Definitions of words used in this manual: ............................. 8
      
4.1 General Warnings: .............................................................. 10
4.2 Features and options:......................................................... 10
4.3 Preliminary checks:............................................................. 10
4.4 Emergency braking:............................................................ 10
4.5 Kerbs: .................................................................................. 10
4.6 Tyres: ................................................................................... 11
4.7 Freewheel device:............................................................... 11
4.8 Electromagnetic Compatibility........................................... 11
  
5.1 Transport of the wheelchair in a car .................................. 12
5.2 The wheelchair as a passenger seat................................... 14
5.3 Using the Dahl Docking System.......................................... 16
5.4 Special transport requirements ......................................... 19
5.5 Hoisting the wheelchair...................................................... 20
5.6 General transport warnings ............................................... 20
  
6.1 Maintenance....................................................................... 21
6.2 Sharp turns: ........................................................................ 22
6.3 Weight limit: ....................................................................... 22
6.4 Hot surfaces:....................................................................... 22
6.5 Road caution:...................................................................... 22
6.6 Adverse conditions: ............................................................ 22
6.7 Ramps:................................................................................. 22
6.8 Transfer to and from the chair: .......................................... 23
6.9 Anti tips:.............................................................................. 23
6.10 Use on a slope:.................................................................. 23
6.11 Gradients: ascents: ........................................................... 23
6.12 Gradients: descents: ........................................................ 23
6.13 Lap strap / seating positioning belt ................................. 24
6.14 Rear View Mirror: ............................................................. 25
      
7.1. Footrest: ............................................................................ 26
7.2. Armrest: ............................................................................ 26
7.3. Anti-tip wheels: ................................................................. 26
7.4. Kerb climber:...................................................................... 27
7.5. Batteries: ........................................................................... 27
7.6. Wheels: .............................................................................. 27
7.7 Crutch Holder:..................................................................... 28
7.8 Lights and indicators:.......................................................... 28
    
8.1 Preparing for stowed transportation: ............................... 29
8.2 Using the Power Recline Facility ....................................... 29
8.3 To use the wheelchair again:.............................................. 29
8.4 Mechanical Fixed Reclining back ....................................... 29
8.5 Centre of Gravity Adjustment ........................................... 30
8.6 Fixed Seat Tilt:..................................................................... 30
8.7 Freewheel device):.............................................................. 30
8.8. Tyre pressure: ................................................................... 30
8.9 Transfers: ........................................................................... 31
8.10 Slopes: .............................................................................. 31
8.11 Laterals ............................................................................. 32
8.12 Mounting a kerb or step:.................................................. 32
8.13 Dismounting the kerb:...................................................... 32
8.14 (Powered) seating options............................................... 33
  
9.1 Pre-set SEDEO LITE swing away legrests............................ 34
9.2 Pre-set UNI swing away legrest.......................................... 34
9.3 Pre-set swing away legrests ............................................... 35
9.4 Pre-set power center mount legrest................................. 36
  
10.1 Pre-set headrest .............................................................. 37
    
11.1 On/Off button:.................................................................. 38
11.2 Battery Level Indicator: .................................................... 38
11.3 Locking/unlocking the wheelchair: .................................. 38
11.4 Operating the control joystick: ........................................ 39
11.5 Maximum speed/profile indicator: .................................. 39
11.6 The horn button: .............................................................. 39
11.7 Speed/Profile decrease button: ....................................... 39
11.8 Speed/Profile increase button: ........................................ 39
11.9 VR2-L ................................................................................. 40
11.10 Charging and programming socket ............................... 41
11.11 VR2 dual control unit:..................................................... 41
11.12 Control button and indicator: ........................................ 41
11.13 Actuator button and LED:............................................... 41
11.14 Maximum speed button and indicator: ......................... 42
11.15 Troubleshooting The VR2 Hand Control: ....................... 42
11.16 Directional Tiller attendant control. .............................. 44
  
12.1 R-net controller ................................................................ 45
12.2 R-net attendant steering.................................................. 45
12.3 Gyro Module..................................................................... 45
12.4 Main Components ........................................................... 46
12.5 Display screen................................................................... 47
12.6 Driving the wheelchair ..................................................... 48
12.7 The electrical adjustment options .................................. 48
12.8 Lights................................................................................. 50
12.9 Troubleshooting............................................................... 50
12.10 Locking the controller.................................................... 50
    
13.1. Battery & Charger Specification: .................................... 51
13.2 Electrical fuses: ................................................................ 51
13.3 Batteries: .......................................................................... 51
13.4 General battery information:........................................... 53
13.5 Maintenance-free batteries:............................................ 53
13.6 Battery care: ..................................................................... 53
13.7 Maintenance-free battery care plan:............................... 53
13.8 General charger information: .......................................... 54
13.9 Charger Specification: ..................................................... 54
13.10 Charger safety features:................................................. 54
13.11 Procedure for connecting the charger and charging: ... 54
13.12 Charger safety and caution notes:................................. 54
13.13 The range of your vehicle:.............................................. 55
13.14 Common battery statements:........................................ 55
     
14.1 Adjustment of the footrest: ............................................ 56
14.2 Inner Or Outer Width Adjustment of the footrests:......... 56
14.3 Adjustment of the armrests: ............................................ 56
14.4 Seat width adjustment: ................................................... 56
14.5 Seat Centre of Gravity Adjustment: ................................ 56
14.6 Seat depth adjustments: ................................................. 57
14.7 Control Adjustment: ........................................................ 57
14.8 Dual/Attendant control (Where fitted)............................ 57
14.9 Parallel swing-away control:............................................. 57
14.10 Programming: ................................................................ 58
     
15.1 Cleaning General: ............................................................. 58
15.2 Cleaning seating: .............................................................. 58
15.3 Cleaning control system:.................................................. 58
15.4 Speciality controls: ........................................................... 58
  
16.1 Storage temperature & humidity: ................................... 59
16.2 Special shipping requirements: ....................................... 59
16.3 Medium to long term storage: ........................................ 59
      
  
   
    
20.1 Re-use .............................................................................. 63

ENGLISH
6Q100R-Q200R Configured Rev. A
1.0 Your Wheelchair:
We at Sunrise Medical want you to get the best out of your
Q100R/Q200R wheelchair. This Owner’s Manual will familiarise
you with the chair and its features. It contains hints on everyday
usage and general care in addition to information on the high
quality standards which we adhere to and details about the
guarantee.
Your wheelchair will be delivered ready for quick assembly
– refer to the quick start guide on the inside cover of this user
manual. There are a wide range of components and adjustments
available on the Q100R/Q200R. For further information about
these you should contact your Sunrise Medical authorised
dealer.
Your wheelchair will reach you in excellent condition having
been personally inspected before leaving our factory. Following
the guidelines for maintenance and cleaning your wheelchair
will maintain its first class condition and give you complete
satisfaction.
The Q100R/Q200R has been designed for use by an individual
on a daily basis. It is suitable for both indoor and outdoor use
(Class B). It is only intended for use as a pavement vehicle, but
may also be used when crossing between pavements.
This vehicle has been designed for a single occupant of
limited mobility up to the weight of Q100R 125Kg and Q200R
136Kg (dependant on options chosen for your chair) who has
the cognitive, physical and visual ability to control the vehicle
safely on a maximum slope – see section 18.0 Specification
Sheet section for maximum slope details. If you are in any
doubt as to the suitability of the power chair, contact your local
Sunrise Medical approved supplier for clarification, prior to
commencing use.
It is very important to read the relevant section of the owner’s
manual when making any minor adjustments. Consult the
Technical Manual or your local Sunrise Medical authorised
dealer for more complex adjustments.
If you have any queries about the use, maintenance or safety
of your wheelchair, please contact your local approved Sunrise
Medical service agent. If you do not know of an approved
dealer in your area or have any other questions please write or
telephone:
Sunrise Medical
Thorns Road
Brierley Hill
West Midlands
DY5 2LD

 
 
www.SunriseMedical.co.uk
2.0 How to use this manual:

Please keep a note of your local service agent’s address and
telephone number in the space below.
In the event of a breakdown, contact them and try to give all
relevant details so they can help you quickly.
The wheelchairs shown and described in this manual may not be
exactly the same in every detail as your own model. However,
all instructions are still entirely relevant, irrespective of detail
differences.
NOTE: The manufacturer reserves the right to alter without
notice any weights, measurements or other technical data
shown in this manual. All figures, measurements and capacities
shown in this manual are approximate and do not constitute
specifications.

ENGLISH
Q100R-Q200R Configured Rev. A 7
2.2 Guarantee
THIS GUARANTEE DOES NOT AFFECT YOUR LEGAL RIGHTS IN ANY WAY.
Sunrise Medical* provides a guarantee, as set out in the warranty conditions, for products to its customers covering the following.

1. Should a part or parts of the product require repair or replacement as a result of a manufacturing and/or material fault within 24
months, then the aected part or parts will be repaired or replaced free of charge. The warranty will only cover manufacturing
defects
2. To enforce the warranty, please contact Sunrise Medical Customer Service with the exact details of the nature of the diculty.
Should you be using the product outside the area covered by the Sunrise Medical customer service agent, repairs or replacement
will be carried out by another agency as designated by the manufacturer The product must be repaired by a Sunrise Medical
designated Customer Service agent, (dealer).
3. For parts, which have been repaired or exchanged within the scope of this warranty, we provide a warranty in accordance with
these warranty condions for the remaining warranty period for the product in accordance with point 1.
4. For original spare parts which have been ed at the customer’s expense, these will have a 12 months guarantee, (following the
ng), in accordance with these warranty condions.
5. Claims from this warranty shall not arise, if a repair or replacement of a product or a part is required for the following reasons:
a. Normal wear and tear, which include but is not limited to the following parts where ed; baeries, armrest pads, upholstery,
tyres, brakes shoes, ferrules, etc.
b. Any overloading of the product, please check the EC label for maximum user weight.
c. The product or part has not been maintained or serviced in accordance with the manufacturer’s recommendaons as shown
in the user instrucons and/or the service instrucons.
d. Accessories have been used which are not specied as original accessories.
e. The product or part having been damaged by neglect, accident or improper use.
f. Changes/modicaons have been made to the product or parts, which deviate from the manufacturer’s specicaons.
g. Repairs have been carried out, before our Customer Service has been informed of the circumstances.
6. This guarantee is subject to the law of the country in which the product was purchased from Sunrise Medical*
7. Life expectancy
We esmate a life expectancy of ve years for this product, provided that:
• It is used in strict accordance with the intended use as set out in this document.
• All maintenance and service requirements are met.
The esmated life expectancy can be exceeded if the product is carefully used and properly maintained, provided that technical
and scienc advances do not result in technical limitaons.
The life expectancy can also be considerably reduced by extreme or incorrect usage.
The fact that we esmate a life expectancy for this product does not constute an addional warranty.
* Means the Sunrise Medical facility from which the product was purchased.

i. For goods provided by Sunrise medical Pty Ltd in Australia, our goods come with a guarantee by Sunrise Medical that cannot be
excluded under Australian Consumer Law.
ii. You are entled to a replacement or refund for a major failure and for compensaon for any foreseeable loss or damage.
iii. You are also entled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not
amount to a major failure.
iv. The benets to you given by this warranty are in addion to your other rights and remedies under a law in relaon to the goods
to which the warranty relates.

ENGLISH
8Q100R-Q200R Configured Rev. A
3.0 Label Explanation / Word definitions:

Word Definition
DANGER!
Advice to the user of Potential Risk of
serious injury or death if the advice is
not followed
WARNING!
Advice to the user of a potential risk of
injury if the advice is not followed
CAUTION!
Advice to user that potential damage
to equipment may occur if the advice
is not followed
NOTE: General advice or best practice
RWD Rear Wheel Drive
Reference To Additional
Documentation

ENGLISH
Q100R-Q200R Configured Rev. A 9
WARNING!
RED
BLACK
RED
RED
Controller connector
YELLOW
Baery connector
Baery wiring schemac
BLACK BLACK
Baery connector

CIRCUIT DIAGRAM

BRAKE RELEASE
DRIVE
FREEWHEEL



ENGLISH
10 Q100R-Q200R Configured Rev. A
4.0 Safety:
If you follow the instructions given in this manual, you will
enjoy many trouble-free years of use:
WARNING!
• This vehicle is not designed for use on the road except for
crossing from one kerb to another.
• Load data always refers to one single person as operator.
• The wheelchair is authorised for use by one person or
one seated person and their attendant if using a Dual or
Attendant control unit.
WARNINGS!

• Always ensure that your wheelchair is switched off before
attempting to mount or dismount.
• Always ensure that you are able to operate all controls from
a comfortable position. Paying attention to your posture is
essential to ensure your continued comfort and well being.
• Always make sure that you can be seen clearly, especially if
you intend using your wheelchair in poor light.
• This wheelchair has been built to match the needs of a
particular user. If used by another user then it may need to
be adjusted and reprogrammed.
• Do not let children or others use your wheelchair.
• Do not lift or hoist the wheelchair by any detachable parts
such as leg rests, arm rests etc.
CAUTION!

Some of the options shown in this manual may not be available
in your country and may also restrict the overall physical limits
of the standard product (e.g. max. speed, user weight limit,
etc.). Those limitations are marked on the order form, in the
technical manual and in this owner’s manual.
For further information please consult your Sunrise Medical
authorised dealer.
WARNING!
CHOKING HAZARD – This mobility aid uses small parts which
under certain circumstances may present a choking hazard to
young children.
DANGER!
4.3 Preliminary checks:
• You should not try to manoeuvre at full speed.
• If you have to make a sudden turn, slow down first using the
joystick or the speed control knob.
• This is very important if you are going down a hill.
• Lack of attention to this point may result in your overturning
the wheelchair.
• Always check that the wheelchair is switched off before
trying to get in or out.
• Always check that you can operate all the controls from a
comfortable seated position. It is essential to pay attention
to posture in order to assure comfort and well-being.
• Always check that the freewheel device is switched off
before setting the chair in motion.
• Always check that you can be seen clearly, especially if you
are using the wheelchair in conditions of low visibility.
WARNING!

If power is cut by means of the ON/OFF button, braking will
be immediate and total. This method of stopping is not
recommended except for emergencies, since the stop will be
extremely sudden.

• Always cross the road as rapidly as possible, since other
vehicles may appear.
• Do not attempt to climb or to descend from, a kerb of more
than 100 mm. height.
• Do not attempt to ascend high kerbs, steep slopes or cambers
due to the risk of falling out of the chair or tipping over.
• Do not attempt to ascend any kerb in the vicinity of a drain
cover, uneven surfaces, or gravel covering.
• Do not attempt to descend a kerb of more than 50 mm in
forward position.
• Do not attempt to climb or descend any kerb at an oblique
angle. Approach only at an angle of 90° with at least 500mm
run-up.


ENGLISH
Q100R-Q200R Configured Rev. A 11

The tyres of a wheelchair suffer wear depending on how much
the chair is used. Check them regularly, especially for inflation
pressure, according to the service instructions in this manual.
WARNING!
Where fitted NEVER inflate pneumatic tyres with the air hose
of a service station.
WARNING!

Also see Fig.3.1
• Only use this function to push the chair manually from one
spot to another.
• Keep in mind that while the freewheel system is in operation,
the chair is without a braking system.
• Disengaging the motor causes an error message to appear in
the control, which is indicated when the LED display flashes
rapidly.
• For safety reasons the wheelchair can no longer be moved
using the joystick.
• Do not operate the freewheel device whilst seated in the
wheelchair.
• The freewheel device should only be operated by a person
who has the strength and agility to be able to fully manoeuvre
the wheelchair safely, during freewheel.


WARNING!
• This wheelchair may affect the operation of devices in its
environment that emit electromagnetic fields (e.g. alarm
systems of shops, automatic doors, etc).
• The driving performance of the wheelchair can be effected
by electromagnetic fields (e.g. those emitted by portable
telephones, electricity generators or high power sources).

ENGLISH
12 Q100R-Q200R Configured Rev. A
5.0 Transportation
5.1 Transport of the wheelchair in a car

DANGER!
• Confirm that the vehicle is suitably equipped to transport a
passenger in a wheelchair, and ensure the method of access/
egress is suitable for your wheelchair type. The vehicle should
have the floor strength to take the combined weight of the
occupant, the wheelchair and accessories.
• Use a ramp (or lifting device) suitable for the entire weight of
the wheelchair (including user) for entering the vehicle.
• The wheelchair should be secured in a forward facing
direction. This wheelchair is approved for use in cars and
meets the requirements for forward facing transport and
head on collisions. The wheelchair has not been tested for
other positions in a vehicle (Fig. 5.1).
CAUTION!
• Sufficient space should be available around the wheelchair
to enable clear access to attach, tighten and release the
wheelchair and occupant tie down restraints and safety belts.
• Ease of access to, and manoeuvrability in, motor vehicles
can be significantly affected by wheelchair size and turning
radius; smaller wheelchairs and/ or wheelchairs with a shorter
turning radius will generally provide greater ease of vehicle
access and manoeuvrability to a forward-facing position.

This wheelchair has been successfully crash tested in accordance
to: ISO 7176-19:2008, using a representing restraint system.
• Secured with a 4-point strap restraint system (2 in the front, 2
in the back, Fig.5.2), that conforms to:
i. ISO 10542 (internaonal) or
ii. SAE J2249 (USA).
NOTE: Wheelchair secured with a 4-point strap restraint system;
suitable for the total weight of the wheelchair (including any
options) in accordance with the WTORS1) manufacturers
instruction.
Terminology explained:
1) WTORS: Wheelchair Tie-down Occupant Restraint System

AFront Tie Down Points.
BRear Tie Down Points.
CDirection of Travel.

A A
BB
C

ENGLISH
Q100R-Q200R Configured Rev. A 13
DANGER!
• The wheelchair can only be secured by using the tie-down
points on the wheelchair’s frame (Fig. 5.2 - 5.8).
• The tie-down points (2 in the front, 2 in the back) are
indicated by the tie-down symbol (Fig. 5.5). Fit the front
straps first, then the rear. Tension the straps to secure the
wheelchair. The wheelchair may not be secured onto any
accessories (wishbones, armrests, anti-tip brackets etc.).
• No changes or replacements must be made to the anchorage
points/car fastenings on the wheelchair, or to constructional
elements or parts of the frame without consulting the
manufacturer.
• When the wheelchair is transported in a vehicle without
occupant and no restraint system is available then the
wheelchair should be properly stored and secured in the
cargo area during travel.
A
C

C

B
AFront Tie Down Points.
BRear Tie Down Points.
CDirection of Travel.



ENGLISH
14 Q100R-Q200R Configured Rev. A

DANGER!
• Use a 3-point occupant restraint system to secure the
occupant.
• Both pelvic and upper torso restraint belts must be used
to restrain the occupant (Fig. 5.9 - overleaf) to reduce
the possibility of head and chest impacts with the vehicle
components.
• Restraints should be mounted to the appropriate vehicle pillar
and should not be held away from the body by wheelchair
components such as armrest or wheels (Fig. 5.10).
• Use a suitable positioned headrest when being transported
in a wheelchair.
• Postural supports (lap straps, lap belts) should not be used
or relied on for occupant restraint in a moving vehicle unless
they are labelled as meeting the requirements specified in
ISO 7176-19:2008 or SAE J2249.

A wheelchair secured in a vehicle will not provide the
equivalent level of safety and security as a vehicle seating
system. Sunrise Medical recommends that the user transfers
to the vehicle seating and uses the vehicle-installed restraint
system wherever possible. Sunrise Medical recognizes that it is
not always practical for the user to be transferred and in these
circumstances, where the user must be transported whilst in
the wheelchair, the following advice must be followed:
DANGER!
• The safety of the user during transportation depends upon
the diligence of the person securing the tie down restraints
and they should have received appropriate instructions and/
or training in their use.
• Wherever possible remove and stow safely away from the
wheelchair all auxiliary equipment, e.g. : crutches, loose
cushions, tray tables, etc.
i. Removed and secured separately in the vehicle, or
ii. Secured to the wheelchair, but with energy-absorbing
padding placed between the table and the user.
• Articulating/elevating leg rest should not be used in the
elevated position when the wheelchair and user are being
transported.
• If applicable: Reclining backrests should be returned to an
upright position.
• If applicable: Seat elevators should be in the lowest position.
• If applicable: The manual brakes must be firmly applied.

ENGLISH
Q100R-Q200R Configured Rev. A 15
30°
75
°
55°
100 mm

DANGER!
• The pelvic restraint belt must be worn low across the front
of the pelvis so that the angle of the pelvic belt is within the
preferred zone of 30° to 75° to the horizontal.
• A steeper (greater) angle within the preferred zone is desirable
i.e. closer to, but never exceeding 75° degrees (Fig. 5.10).
i. The upper torso restraint belt must t over the shoulder
and across the chest as illustrated (Fig. 5.9). Restraint belts
must be adjusted as ghtly as possible consistent with
user comfort.
• Restraint belt webbing must not be twisted when in use.
• Care should be taken when applying the occupant restraint to
position the seatbelt buckle so that the release button will not
be contacted by wheelchair components during a crash.

When the user being transported is a child, less than 22 kg
mass and the vehicle involved has less than eight (8) seated
passengers it is recommended that they be transferred to an
UNCE Regulation 44 compliant child restraint system (CRS).
This type of restraint system provides a more effective occupant
restraint system than the conventional 3 point occupant
restraint system and some CRS systems also include additional
postural supports to assist in maintaining the position of the
child when seated.
Parents or care providers may consider the option, in some
circumstances, for their child is to remain in their wheelchair
whilst in transport due to the level of posture control and
comfort provided by the set up in the wheelchair.
We would recommend in such circumstances that a risk
assessment be carried out by your healthcare professional and
relevant competent persons.



ENGLISH
16 Q100R-Q200R Configured Rev. A




1 mm
Optional,
max 3 mm
8mm
2 mm

CAUTION!
The installation should be performed or supervised by a
technician. Read all instructions carefully before proceeding
with the installation.
To install Docking Plate use Dahl Adaption Kit #503259
1. Fit the 8 mm spacer onto the lock plate (Fig. 5.11).
3. Put the five screws through the lock plate, the mandatory
8 mm spacer and the selected optional spacers (gray in
picture) (Fig. 5.13).
WARNING!
Do not use any other screws than those supplied from Dahl
engineering (Part #502800 which is Quality 14.9 with Torx
Key Size 27). Standard screws will not be strong enough in the
event of a collision.
4. Mount the five screws together with the spacer/spacers
and the lock plate on the underside of the chassis box
(Fig. 5.14).
2. Use more spacers to achieve desired thickness with
regards to, for instance, user weight and tire pressure.
Additional spacers can be mounted under the locking
station (Fig. 5.12). To align the height of the lock plate
under wheelchair with the docking station fit spacers
between the docking station and the vehicle floor to raise
the docking station.
Mandatory

ENGLISH
Q100R-Q200R Configured Rev. A 17
x5
x5




5. Mark where to cut the screws. (Fig. 5.15).
6. Remove the screws together with the spacer/spacers (Fig. 5.16).
7. Cut the screw where the mark is (Fig. 5.17).
It is very important that the fitter checks that the length of the
bolts are correct. If bolts are too short to reach through all the
threads - they will not have the strength to carry the loads
required. If bolts are too long the batteries or other wheel chair
components can be damaged. If necessary replace with longer
bolts, or shorten them.
8. Apply Loctite 222 (or an equivalent product) onto the screw
(Fig. 5.18).

ENGLISH
18 Q100R-Q200R Configured Rev. A
9. Attach the five screws together with the plastic spacer/
spacers (to prevent the batteries from coming into contact
with the nuts) and the lock plate on the underside of the
chassis box. Tightening torque: 16-18 Nm/13.3 lb.ft (Fig.
5.19).
Please refer to Section 6.6 of this manual for reverse the
procedure to replace batteries.
C
A
F
F
B
D E


10. Perform final check by connecting the wheelchair to the
docking station. Check that it is securely locked and make
sure that all release methods work as intended (Fig. 5.20).
A warning tone will sound if the lock plate is not properly
engaged.
(A) Release button.
(B) Manual operating lever.
(C) Emergency release.
(D) Red LED.
(E) Green LED.
(F) Lock Plate.
(G) Lock Pin.

Make sure that the leg rests are not colliding with the ramp or
the docking station when entering the vehicle.
1. Maneuver the wheelchair slowly and in a uniform direction
over the docking station. The lock plate under the wheelchair
helps to guide the wheelchair into place in the docking
station. When the lock plate is fully engaged in the docking
station, a spring-action locking pin automatically secures the
lock plate.
2. The docking station is equipped with a control switch that
indicates whether the lock plate is correctly secured in the
docking station. As soon as the lock plate comes into contact
with the locking pin, a warning tone will sound (a high-pitched
howl), and the red diode/lamp (LED) in the control panel will
light up until the lock plate is either fully engaged or else the
wheelchair is removed from the docking station.
3. As an indication that the wheelchair is properly secured, the
warning tone will cease, the red diode in the control panel
will go out and the green diode lamp (LED) will light up.
4. Do not forget to buckle up for driving.

1. When the vehicle has been brought to a halt, remove the
safety belt.
2. To unlock commence by driving the wheelchair forward to
release pressure on the lock pin and then press the red
release button in the control panel. The locking pin will be
triggered/released for approx. 5 seconds, after which the
locking pin is automatically locked/activated again. Do not
attempt to reverse out of the docking station until the red LED
on the control module, which indicates the unlock position,
has been illuminated.
WARNING! Attempting to reverse the wheelchair before the
red LED has been illuminated will result in blocking the
docking stations lock mechanism, which makes it impossible
to reverse. If this happens repeat above unlocking procedure.
3. Move the wheelchair away from the docking station within
this 5-second period.
Manual release in case of electrical failure
1. In the event of electrical failure, a manual emergency release
is located at the front edge of the docking station. Move
wheelchair forward to release pressure on the lock pin and
push the red release arm to one side and hold it there while
the wheelchair reverses out of the docking station.
2. A cable-activated manual operating lever can also be fitted
(accessory). The red release arm must pushed to one side
and should be held there whilst the wheelchair moves away.
3. If the described manual release procedures fails, an
emergency release tool made from red plastic comes with
each docking station.
Move wheelchair forward to release pressure on the lock pin
and place the emergency release tool in the gap between the
locking plate and the docking station. Push the release tool
forward until the locking pin will has been forced down - after
which the wheelchair can be reversed out of the docking station.



VarioDock™ system.

ENGLISH
Q100R-Q200R Configured Rev. A 19

• Remove seat belt fixings (13mm socket/6mm allen key)
• Make note of quick release pin location
• Remove quick-release pin
• Assemble seat belt screw and washer to Dahl cover
• Assemble seat belt to screw, seat belt should be located in
cut out
• Push fit cover onto backrest pivot screw
• Assemble quick release pin into correct recline hole
• Assemble nut to seat belt screw and tighten to 5-6Nm.
NOTE!
Necessary covers when using Dahl Docking Station. Not
supplied by Dahl.




Before you travel, please contact the train operator. They will be
able to supply details of any special requirements/instructions.
We advise you to check the following:
• Is there a suitable and intended “wheelchair” area in the
train for wheelchair users (with adequate turning space to
manoeuvre)?
• Is there a suitable or designated area on the platform for
wheelchair users (with adequate turning space to manoeuvre)?
• Is there suitable boarding access available to allow you to
access the railway carriage and the intended “wheelchair”
area?
• Is the boarding access suitable for the combined mass of the
wheelchair and the occupant?
• Make sure the slope of the boarding access is not greater than
the dynamic safe slope. (See Section 16)
• Any obstacles or thresholds should not exceed the max kerb
climbing capability of your wheelchair. (See Section 16)
Most train operators will provide assistance provided that
arrangements have been made in advance. We suggest you
have you Owner’s Manual ready when planning your journey
and contacted them.

ENGLISH
20 Q100R-Q200R Configured Rev. A

Parts of the wheelchair that can easily be detached should be
removed when transporting the wheelchair. Store these parts
securely. E.g.:
A. Remove the leg rests
B. Remove the armrests
C. Fold down the backrest
• Ensure that any detachable parts are secured with your
mobility aid or separately packed and labelled so they do not
get lost during loading and unloading.
• The wheelchair may be transported by road, rail, sea or air.
• Before you travel, please contact the appropriate carrier. The
travel operator will be able to supply details of any special
requirements/instructions.
• For information about dimensions and weight of the
wheelchair, see (Section 16).
• For information about the batteries in your wheelchair see
(Section 6).
• Ensure that any detachable parts are secured with your
mobility aid or separately packed and labelled so they do not
get lost during loading and unloading.
• Take this user manual with you. The carrier will need to refer
to the following sections:
i. Pushing the wheelchair.
ii. How to lock/unlock the controller.
iii. How to disconnect the baeries.
iv. How to disconnect the drive.
• Transporting the chair.
• Medium to long term storage, follow the instructions.

The most forward seat depth holes provide a reference
balance position for 2 point lifting systems (individual chair
configuration and options may require alternative position).


WARNING!
• No changes or replacements must be made to the anchorage
points/car fastenings on the wheelchair, or to constructional
elements or parts of the frame without consulting Sunrise
Medical.
• The wheelchair should be inspected by a Sunrise Medical
authorised dealer/service agent, before reuse following
involvement in any type of vehicle collision.