Supermicro SC113MFAC2-605CB User manual

SC113M
CHASSIS SERIES
USER’S MANUAL
1.1
SC113MFAC2-605CB
SC113MTQ-563CB
SC113MTQ-330CB
SC113MFAC2-R606CB
SC113MTQ-600CB
SC113MTQ-R400CB

SC113M Chassis Manual
ii
Manual Revision 1.1
Release Date: April 5, 2017
The information in this User’s Manual has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document,
makes no commitment to update or to keep current the information in this manual, or to notify any
person or organization of the updates. Please Note: For the most up-to-date version of this
manual, please see our web site at www.supermicro.com.
Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product
described in this manual at any time and without notice. This product, including software and
documentation, is the property of Supermicro and/or its licensors, and is supplied only under a
license. Any use or reproduction of this product is not allowed, except as expressly permitted by
the terms of said license.
IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,
SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO
USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY
HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE
COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH
HARDWARE, SOFTWARE, OR DATA.
Any disputes arising between manufacturer and customer shall be governed by the laws of Santa
Clara County in the State of California, USA. The State of California, County of Santa Clara shall
be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for all
claims will not exceed the price paid for the hardware product.
California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate
warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate
Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”
WARNING: Handling of lead solder materials used in this
product may expose you to lead, a chemical known to
the State of California to cause birth defects and other
reproductive harm.
Unless you request and receive written permission from Super Micro Computer, Inc., you may not
copy any part of this document.
Information in this document is subject to change without notice. Other products and companies
referred to herein are trademarks or registered trademarks of their respective companies or mark
holders.
Copyright © 2017 by Super Micro Computer, Inc.
All rights reserved.
Printed in the United States of America

iii
Preface
Preface
This manual is written for professional system integrators and PC technicians. It
provides information for the installation and use of the SC113M chassis. Installation
and maintenance should be performed by experienced technicians only.
Supermicro’s SC113M 1U chassis packages outstanding high-end performance
into an astonishingly short 20” deep chassis, featuring advanced airow/thermal
design for space-limited applications. With its short depth, it efciently packages
eight hot-swappable 2.5” SAS/SATA hard drive bays into a compact 1U form factor.
This chassis features a 330W, 400W, 560W or 600W power supply.
This document lists compatible parts and congurations available when this docu-
ment was published. Always refer to our website for updates on supported parts
and congurations at www.supermicro.com

SC113M Chassis Manual
iv
Manual Organization
Chapter 1 Introduction
The introduction provides a checklist of the main components included with this
chassis and describes the main features of the SC113M chassis. This chapter also
includes contact information.
Chapter 2 Standardized Warning Statements for AC Systems
This chapter lists warnings, precautions, and system safety. You should thoroughly
familiarize yourself with this chapter for a general overview of safety precautions
that should be followed before installing and servicing this chassis.
Chapter 3 Chassis Components
Refer here for details on this chassis model, including the fans, bays, airow shields,
and other components.
Chapter 4 System Interface
This chapter provides details on the system interface, which includes the functions
and information provided by the control panel on the chassis, as well as other LEDs
located throughout the system.
Chapter 5 Chassis Setup and Maintenance
Refer to this chapter for detailed information on this chassis. Follow the procedures
given in this chapter when installing, removing, or reconguring your chassis.
Chapter 6 Rack Installation
Refer to this chapter for detailed information on chassis rack installation. You should
follow the procedures given in this chapter when installing, removing or reconguring
your chassis into a rack environment.

v
Preface
Appendix A Cables
This section references cables, which are compatible with your SC113M system.
Refer to our website for additional information on cabling at www.supermicro.com.
Appendix B Power Supply
This chapter lists supported power supply information for your SC113M system.
Refer to our website for additional details at www.supermicro.com.
Appendix C BPN-SAS-113TQ Backplane Specications
This chapter provides information on the BPN-SAS-113TQ backplane. For additional
information visit the Supermicro website at www.supermicro.com
Appendix D BPN-SAS3-113A-N2 Backplane Specications
Refer to this chapter for information on the BPN-SAS3-113A-N2 backplane. For
additional information visit the Supermicro website at www.supermicro.com

SC113M Chassis Manual
vi
Table of Contents
Chapter 1 Introduction
1-1 Overview ......................................................................................................... 1-1
1-2 Shipping List.................................................................................................... 1-1
1-3 Contacting Supermicro.................................................................................... 1-2
1-4 Returning Merchandise for Service................................................................. 1-3
Chapter 2 Standardized Warning Statements for AC Systems
2-1 About Standardized Warning Statements....................................................... 2-1
Warning Denition ........................................................................................... 2-1
Installation Instructions.................................................................................... 2-4
Circuit Breaker ................................................................................................ 2-5
Power Disconnection Warning ........................................................................ 2-6
Equipment Installation..................................................................................... 2-8
Restricted Area................................................................................................ 2-9
Battery Handling............................................................................................ 2-10
Redundant Power Supplies .......................................................................... 2-12
Backplane Voltage ........................................................................................ 2-13
Comply with Local and National Electrical Codes........................................ 2-14
Product Disposal........................................................................................... 2-15
Hot Swap Fan Warning................................................................................. 2-16
Power Cable and AC Adapter ...................................................................... 2-18
Chapter 3 System Interface
3-1 Overview ......................................................................................................... 3-1
3-2 Control Panel Button and LEDs...................................................................... 3-2
3-3 Drive Carrier LEDs.......................................................................................... 3-4
Chapter 4 Chassis Setup and Maintenance
4-1 Overview ......................................................................................................... 4-1
4-2 Removing Power From the Chassis ............................................................... 4-1
4-3 Removing the Chassis Cover ......................................................................... 4-2
4-4 Installing Hard Drives...................................................................................... 4-3
4-5 Installing the Motherboard .............................................................................. 4-5
Permanent and Optional Standoffs................................................................. 4-5
Installing the Motherboard .............................................................................. 4-6
Expansion Card Setup .................................................................................... 4-7
4-6 Removing the Backplane ................................................................................ 4-9
4-7 Backplane Installation ................................................................................... 4-10

vii
Preface
4-8 Installing the Air Shroud.................................................................................4-11
4-9 Checking the Airow ..................................................................................... 4-12
Completing the Installation............................................................................ 4-13
4-10 System Fans ................................................................................................. 4-14
4-11 Power Supply ............................................................................................... 4-16
Replacing a Fixed Power Supply.................................................................. 4-16
Replacing a Redundant Power Supply......................................................... 4-17
Chapter 5 Rack Installation
5-1 Overview ......................................................................................................... 5-1
5-2 Unpacking the System .................................................................................... 5-1
5-3 Preparing for Setup......................................................................................... 5-1
Choosing a Setup Location............................................................................. 5-1
Rack Precautions............................................................................................ 5-2
General Server Precautions............................................................................ 5-2
Rack Mounting Considerations ............................................................................
Ambient Operating Temperature .....................................................................
Reduced Airow ..............................................................................................
Mechanical Loading ........................................................................................
Circuit Overloading..........................................................................................
Reliable Ground ..............................................................................................
Rack Mounting Considerations ....................................................................... 5-3
Ambient Operating Temperature ................................................................ 5-3
Reduced Airow ......................................................................................... 5-3
Mechanical Loading ................................................................................... 5-3
Circuit Overloading..................................................................................... 5-3
Reliable Ground ......................................................................................... 5-3
Identifying the Sections of the Rack Rails...................................................... 5-4
Inner Rails....................................................................................................... 5-4
Locking Tabs ................................................................................................... 5-4
Outer Rails ...................................................................................................... 5-5
Appendix A SC113M Chassis Cables
Appendix B SC113M Power Supply Specications
Appendix C BPN-SAS-113TQ Backplane Specications
Appendix D BPN-SAS3-113A-N2 Backplane Specications

Chapter 1
Introduction
1-1 Overview
Supermicro’s SC113M 1U chassis featues 8 hot-swappable 2.5” SAS/SATA hard
drive bays. Only SAS or enterprise HDDs are recommended. The SC113M chassis.
includes a 330, 400, 560 or 600 Watt high-efciency power supply and one slim
DVD-ROM drive.
1-2 Shipping List
Chapter 1: Introduction
1-1
SC113M
Model HDD PCI Slots Power
Supply
SC113MFAC2-R606CB 8x 2.5" hot-swap
SAS/SATA 1x FH 600W (Redundant)
SC113MFAC2-605CB 8x 2.5" hot-swap
SAS/SATA 1x FH 600W
SC113MTQ-600CB 8x 2.5" hot-swap
SAS/SATA 1x FH 600W
SC113MTQ-563CB 8x 2.5" hot-swap
SAS/SATA 1x FH 560W
SC113MTQ-R400CB 8x 2.5" hot-swap
SAS/SATA 1x FH 400W (Redundant)
SC113MTQ-330CB 8x 2.5" hot-swap
SAS/SATA 1x FH 330W

SC113M Chassis Manual
1-2
1-3 Contacting Supermicro
Headquarters
Address: Super Micro Computer, Inc.
980 Rock Ave.
San Jose, CA 95131 U.S.A.
Tel: [phone]
Fax: [phone]
Email: [email protected] (General Information)
[email protected] (Technical Support)
Website: www.supermicro.com
Europe
Address: Super Micro Computer B.V.
Het Sterrenbeeld 28, 5215 ML
's-Hertogenbosch, The Netherlands
Tel: [phone]
Fax: [phone]
Email: [email protected] (General Information)
[email protected] (Technical Support)
[email protected] (Customer Support)
Website: www.supermicro.nl
Asia-Pacic
Address: Super Micro Computer, Inc.
3F, No. 150, Jian 1st Rd.
Zhonghe Dist., New Taipei City 235
Taiwan (R.O.C)
Tel: [phone]
Fax: [phone]
Email: [email protected]
Website: www.supermicro.com.tw

1-3
Chapter 1: Introduction
1-4 Returning Merchandise for Service
A receipt or copy of your invoice marked with the date of purchase is required be-
fore any warranty service will be rendered. You can obtain service by calling your
vendor for a Returned Merchandise Authorization (RMA) number. When returning to
the manufacturer, the RMA number should be prominently displayed on the outside
of the shipping carton, and mailed prepaid or hand-carried. Shipping and handling
charges will be applied for all orders that must be mailed when service is complete.
For faster service, RMA authorizations may be requested online (http://www.super-
micro.com/support/rma/).
Whenever possible, repack the chassis in the original Supermicro carton, using the
original packaging material. If these are no longer available, be sure to pack the
chassis securely, using packaging material to surround the chassis so that it does
not shift within the carton and become damaged during shipping.
This warranty only covers normal consumer use and does not cover damages in-
curred in shipping or from failure due to the alteration, misuse, abuse or improper
maintenance of products.
During the warranty period, contact your distributor rst for any product problems.