Supermicro M12SWA-TF User manual

M12SWA-TF
ENGLISH
繁體中文
简体中文
日本語
( 한국어
QUICK REFERENCE GUIDE
Revision 1.0b

M12SWA-TF QUICK REFERENCE GUIDE
Standardized Warning Statements
Motherboards
About Standardized Warning Statements
The following statements are industry standard warnings, provided to warn the user of situations where bodily injury
might occur. Should you have questions or experience di󰀩culty, contact Supermicro's Technical Support Department
for assistance. Only certied technicians should attempt to install or congure components.
Read this section in its entirety before installing or conguring components in the Supermicro chassis.
WARNING: This product can expose you to chemicals including
lead, known to the State of California to cause cancer and birth
defects or other reproductive harm. For more information, go
to www.P65Warnings.ca.gov.
!
Battery Handling
Warning!
There is a danger of explosion if the battery is replaced incorrectly. Replace the battery only with the same or an equiva-
lent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions.
警告
電池更換不當會有爆炸危險。請使用製造商建議之相同或功能相當的電池更換原有電池。請按照製造商的說明指示處理
廢棄舊電池。
警告
电池更换不当会有爆炸危险。请只使用同类电池或制造商推荐的功能相当的电池更换原有电池。请按制造商的说明处理
废旧电池。
電池の取り扱い
電池交換が正しく行われなかった場合、破裂の危険性があります。 交換する電池はメーカーが推奨する型、または同等のもの
を使用下さい。 使用済電池は製造元の指示に従って処分して下さい。
경고!
배터리가 올바르게 교체되지 않으면 폭발의 위험이 있습니다. 기존 배터리와 동일하거나 제조사에서 권장하는 동등한
종류의 배터리로만 교체해야 합니다. 제조사의 안내에 따라 사용된 배터리를 처리하여 주십시오.




Note: For complete product safety information, refer to http://www.supermicro.com/about/policies/safety_information.cfm.
Product Safety Information

M12SWA-TF QUICK REFERENCE GUIDE 限用物質含有情況標示聲明書
限
限
用
用
物
物
質
質
含
含
有
有
情
情
況
況
標
標
示
示
聲
聲
明
明
書
書
設備名稱：主機板 /
Motherboard
型號（型式）：M12SWA-TF
單元Ｕnit
限用物質及其化學符號
鉛Lead
(Pb) 汞Mercury (Hg) 鎘Cadmium (Cd)
六價鉻
Hexavalent
chromium
(Cr+6)
多溴聯苯
Polybrominated
biphenyls
(PBB)
多溴二苯醚
Polybrominated
diphenyl ethers
(PBDE)
主機板
(Motherboard)
－○○○○○
備考1.〝超出0.1 wt %〞及〝超出0.01 wt %〞係指限用物質之百分比含量超出百分比含量基準
值。
備考2.〝○〞係指該項限用物質之百分比含量未超出百分比含量基準值。
備考3.〝－〞係指該項限用物質為排除項目。
Equipment name
Type designation (Type)
Restricted substances and its chemical symbols
Declaration of the Presence Condition of the Restricted Substances Marking
Note 1
：
“Exceeding 0.1 wt %” and “exceeding 0.01 wt %” indicate that the percentage content of the restricted substance exceeds the
reference percentage value of presence condition.
Note 2
：
“○” indicates that the percentage content of the restricted substance does not exceed the percentage of reference value of presence.
Note 3
：
The “−” indicates that the restricted substance corresponds to the exemption.

M12SWA-TF QUICK REFERENCE GUIDE
NOTES

M12SWA-TF
Quick RefeRence Guide Rev. 1.0a
SUPERMICR R
BAR CODE
BAR CODE
M12SWA-TF
REV:1.00
DESIGNED IN USA
BIOS LICENSE
IPMI CODE
MAC CODE
SAS CODE
DIMME1~H1
FAN5
SATA0
JPW1
JTPM1
VGA
JWP1
JSPDIF_OUT
JPAC1
UID LED
J31
BMC LED
CPU SLOT1 PCIe 4.0 X16 CPU SLOT2 PCIe 4.0 X16 CPU SLOT3 PCIe 4.0 X16 CPU SLOT5 PCIe 4.0 X16 CPU SLOT6 PCIe 4.0 X16 CPU SLOT7 PCIe 4.0 X16
FANC FAN6 FAND
CPU
DIMMA1~D1
JPW4
FAN4 FAN3 JWD1 FANB FANA
JSTBY1
FAN1 FAN2
BT1
SATA1
JL1
COM2
JWP2
JSD1
COM1
JUSBLAN1
JPW2
M.2-0LED
M.2-1LED
M.2-2LED
M.2-3LED
JBT1
JF1
JPI2C1: PWR I2C
JOH1
USB 2/3
Motherboard Layout and Features
=mounting hole
I/O BACK PANEL
PCH_FAN
JAUDIO1
USB 6/7
USB 8/12
LAN 1
JPW3
JP5
JPL1
12V PUMP PWR1
JD1
SATA2 SATA3 USB 10/11 USB 9
USB 0/1
M.2 NVME
M.2 NVME
M.2 NVME
USB 4/5
U.2
JPL2
JPUSB1
LAN 2

Package contents
• One Supermicro Motherboard
• Four SATA Cables
• One I/O Shield
• One Quick Reference Guide
• One GPU to CPU Power Cable
• M.2 Screw and Stand Kit
Connector Description
JD1 Front Panel External Speaker
J31 Front Panel Audio FP Header
BT1 Onboard Battery
COM1 COM1: COM Port (Back Panel)
CPU SLOT1~7 PCIe 4.0 x16 Slots
FAN1 ~ FAN6 CPU Fan Headers
FANA ~ FAND System Fan Headers
12V_PUMP_PWR1 12V 4-pin power connector for liquid cooling CPU pump
SATA0~3 Serial ATA (SATA 3.0) Ports (6Gb/second)
JSD1 SATA DOM Power Connector
JF1 Front Control Panel Header
JL1 Chassis Intrusion Header
JOH1 Overheat LED Header
JPI2C1 Power Supply SMBus I2C Header
JPW1 24-pin ATX Main Power Connector (Required)
JPW2~JPW4 +12V 8-pin CPU Power Connectors (Required)
JSTBY1 Standby Power Header (5V)
JTPM1 Trusted Platform Module (TPM)/Port 80 Header
JSPDIF Out SPDIF (Sony/Philips Digital Interface) Out Headers
USB0/1 USB 2.0 Front Panel Header
USB10/11 USB 3.2 (Gen. 1) Type A Front Panel Header
USB9 USB 3.2 (Gen. 2) Type C Front Panel Header
VGA VGA Port
Jumpers and Connectors
Jumpers
Jumper Description Default
JBT1 Clear CMOS (Onboard) Short Pads to Clear CMOS
JPAC1 HD Audio Enable/Disable Pins 1-2 (Enabled)
JPL1, JPL2 LAN1/LAN2 Enable/Disable Pins 1-2 (Enabled)
JPUSB1 USB6/7 Wake Up Pins 1-2 (Enabled)
JWD1 Watch Dog Time Control Pins 1-2 (Reset)
JP5 USB 12 Enable/Disable Pins 1-2 (Enabled)
Connectors
LED Description Color/State
M.2-0LED, M.2-1LED,
M.2-2LED, M.2-3LED M.2 LEDs for M.2-4/M.2-3/M.2-2/M.2-1 Blinking Green: Device Working
BMC LED BMC Heartbeat LED Blinking Green: BMC Normal
Power LED Onboard Power LED Solid Green: Power On
UID-LED Unit Identier (UID) LED Blue On: Unit Identied
LED Indicators
LED Indicators
Notes:
• It is recommended that you connect both 8-pin (JPW3) and 24-pin (JPW1) connectors to your power supply modules
before powering on the motherboard.
• For installing multiple GPU cards, both 8-pin connectors (JPW2 and JPW4) must be connected.

ContaCt InformatIon
• www.supermicro.com (Email: [email protected])
• Manuals: http://www.supermicro.com/support/manuals
• Drivers & Utilities: https://www.supermicro.com/wdl/
• Safety: http://www.supermicro.com/about/policies/safety_information.cfm
The M12SWA-TF motherboard supports AMD Ryzen™ Threadripper™ PRO 3000 Series Processors, with up to 64 cores. Memory supports up
to 8 DDDR4 ECC and non-ECC, buffered and unbuffered, UDIMM, RDIMM, and 3DS RDIMM sockets, with speeds of up to 3200MHz (1DPC).
Max capacity is up to 256GB (UDIMM) or 2TB (RDIMM) in 8 DDR4 DIMM slots. Populating these DIMM slots with a pair of memory modules
of the same type and size will result in interleaved memory, which will improve memory performance.
Notes:1) For memory optimization, use only DIMM modules that have been validated by Supermicro. For the latest memory updates,
please refer to our website at http://www.supermicro.com/products/motherboard.
2) Always connect the power cord last, and always remove it before adding, removing, or changing any hardware components.
3) Always connect the power cord to both 24-pin (JPW1) and 8-pin (JPW3) connectors before powering on the motherboard.
4) For installting multiple GPU cards, both 8-pin connectors (JPW2 and JPW4) must be connected.
CPU & Memory Support
Front Control Panel (JF1)
Power Button
UID LED
NIC1 Active LED
Reset Button
HDD LED
PWR LED
Reset
PWR
P3V3_STBY_UID SW
P3V3_STBY
Ground
19
X
Ground
X
P3V3_STBY
20
1 2
Ground
Power Fail LED
NIC2 Active LED
SW_NMI_N
P3V3
OH/Fan Fail LED
P3V3
Memory Population
Guidelines
• For optimal performance, it is recom-
mended that DDR4 DIMM modules of
the same size, type, and speed should
be installed.
• Mixed DIMM speeds can be installed.
However, all DIMMs will run at the speed
of the slowest DIMM.
• When installing memory modules, the
DIMM slots should be populated in the
following order: DIMMC1, DIMMD1,
DIMMG1, DIMMH1, DIMMA1, DIMME1,
DIMMB1, DIMMF1.
CPU
DIMMA1 DIMMB1 DIMMC1 DIMMD1
DIMMH1 DIMMG1 DIMMF1 DIMME1
DIMM Memory Installation
DIMM Population Guide
CPU# Channel
D1 C1 B1 A1 E1 F1 G1 H1
1 DIMM
CPU1 V
2 DIMMs
CPU1 V V
4 DIMMs
CPU1 V V V V
6 DIMMs
CPU1 V V V V V V
8 DIMMs
CPU1 V V V V V V V V

MNL-2336-QRG-100
© 2021 Supermicro Computer Inc. All rights reserved. Reproduction of this document whether in part or in whole is strictly prohibited without Supermicro's written consent. All Trademarks are property of their respective entities. All information provided is deemed accurate at the time of printing; however, it is not guaranteed.
Notes
• Graphics shown in this quick reference guide are for illustration purposes only. Your compo-
nents may or may not look exactly the same as the drawings shown in this guide.
• Refer to Chapter 2 of the User Manual for detailed information on jumpers, connectors, LED
indicators, memory support and CPU/motherboard installation instructions.
Screw #3
CPU Installation
Back Panel I/O Connectors
PHM Installation
1
1Lower the heatsink down till it rests
securely over the four screw holes on the
socket frame of the CPU Package.
Screw #1
Screw #2
Screw #3
Carrier Frame/
CPU Package
External Cap
1
1Unscrew the screws
holding down Force Frame
in the sequence of 3-2-1.
1
2Remove the External Cap. 1 3Slide the Carrier Frame/
CPU Package downwards to the
bottom.
1
2As illustrated, tighten the four
screws down on the heatsink in a
diagonal pattern till it is secured.
Screw #1
Screw #2
Screw #4
A. COM1 F. USB6: USB3.2 Gen2
(Type A, 10Gb/s)
K. USB 2: USB3.2 Gen2
(Type A, 10Gb/s) P. Line In
B. VGA Port G. USB7: USB3.2 Gen2
(Type A, 10Gb)
L. USB 3: USB3.2 Gen2
(Type A, 10Gb/s) Q. Line Out
C. 1Gb LAN Port (i210) H. 10Gb LAN Port (AQC113C) M. Center/LFE Out R. Mic In
D. USB12: USB3.2 Gen1
(Type A, 5Gb/s)
I. USB 4: USB3.2 Gen1
(Type A, 5Gb/s) N. Surround Out S. UID Switch
E. USB8: USB3.2 Gen2x2
(Type C, 20Gb/s)
J. USB5: USB3.2 Gen1
(Type A, 5Gb/s) O. S/PDIF Out
M12SWA-TF
AC
LD
E
F
G
H
I
J
K
M
N
O
P
Q
R
SB

美超微電腦股份有限公司
X12SWA-TF 快速參考指南版本 1.0a
SUPERMICR R
BAR CODE
BAR CODE
M12SWA-TF
REV:1.00
DESIGNED IN USA
BIOS LICENSE
IPMI CODE
MAC CODE
SAS CODE
DIMME1~H1
FAN5
SATA0
JPW1
JTPM1
VGA
JWP1
JSPDIF_OUT
JPAC1
UID LED
J31
BMC LED
CPU SLOT1 PCIe 4.0 X16 CPU SLOT2 PCIe 4.0 X16 CPU SLOT3 PCIe 4.0 X16 CPU SLOT5 PCIe 4.0 X16 CPU SLOT6 PCIe 4.0 X16 CPU SLOT7 PCIe 4.0 X16
FANC FAN6 FAND
CPU
DIMMA1~D1
JPW4
FAN4 FAN3 JWD1 FANB FANA
JSTBY1
FAN1 FAN2
BT1
SATA1
JL1
COM2
JWP2
JSD1
COM1
JUSBLAN1
JPW2
M.2-0LED
M.2-1LED
M.2-2LED
M.2-3LED
JBT1
JF1
JPI2C1: PWR I2C
JOH1
USB 2/3
主機板元件配置圖
= 裝機孔
I/O 後擋板
PCH_FAN
JAUDIO1
USB 6/7
USB 8/12
LAN 1
JPW3
JP5
JPL1
12V PUMP PWR1
JD1
SATA2 SATA3 USB 10/11 USB 9
USB 0/1
M.2 NVME
M.2 NVME
M.2 NVME
USB 4/5
U.2
JPL2
JPUSB1
LAN 2